Operator's Manual
Table Of Contents
- 1. REGULATORY AND SAFETY INFORMATION
- 1.1 SAFETY SYMBOL CONVENTIONS
- 1.2 RF ENERGY EXPOSURE AWARENESS AND CONTROL INFORMATION FOR FCC OCCUPATIONAL USE REQUIREMENTS
- 1.3 COMPLIANCE WITH RF EXPOSURE STANDARDS
- 1.4 REGULATORY APPROVALS
- 1.5 OCCUPATIONAL SAFETY GUIDELINES AND SAFETY TRAINING INFORMATION
- 1.6 COMMON HAZARDS
- 1.7 SAFE DRIVING RECOMMENDATIONS
- 1.8 OPERATING RULES AND REGULATIONS
- 1.9 OPERATING TIPS
- 2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ
- 3. INTRODUCTION
- 4. BASIC OPERATION
- 4.1 RADIO CONTROLS
- 4.2 before first use
- 4.3 POWER ON AND SET VOLUME
- 4.4 vida® ID
- 4.5 RADIO DISPLAYS
- 4.6 STATUS MESsages
- 4.7 PREDEFINED MENU LAYOUTS
- 4.8 MENU
- 4.9 ALERT TONES
- 4.10 SELECT ZONE/SYSTEM
- 4.11 SELECT GROUP/CHANNEL
- 4.12 GROUP CALLS
- 4.13 INDIVIDUAL CALLS
- 4.14 USER PROFILES
- 4.15 NOISE CANCELLATION
- 4.16 VOICE ANNUNCIATION
- 4.17 ENABLE/DISABLE ENCRYPTION
- 4.18 CHANNEL GUARD (ANALOG CONVENTIONAL ONLY)
- 4.19 USE TALKAROUND TO BYPASS REPEATER (ANALOG AND P25 CONVENTIONAL ONLY)
- 4.20 CALL ALERT (PAGE)
- 4.21 TELEPHONE INTERCONNECT
- 4.22 DTMF
- 4.23 AUDIO PLAYBACK
- 4.24 START SCAN
- 4.25 STOP SCAN
- 4.26 MONITOR AND SQUELCH TYPES (CONVENTIONAL ONLY)
- 4.27 NUISANCE DELETE
- 4.28 Failsoft (P25 Trunked)
- 4.29 EMERGENCY OPERATION
- 4.30 MDC-1200 (ANALOG CONVENTIONAL ONLY)
- 5. ADVANCED OPERATIONS
- 5.1 VIEW/CHANGE PERSONALITIES
- 5.2 SITUATIONAL AWARENESS (SA) – P25 CONVENTIONAL ONLY
- 5.3 User Defined Zones
- 5.4 Mixed System Zone
- 5.5 CH INFO MENU
- 5.6 AUDIO SETTINGS
- 5.7 DISPLAY SETTINGS
- 5.8 GPS SETTINGS
- 5.9 POSITION INFO
- 5.10 BLUETOOTH
- 5.11 CLOCK SETTINGS
- 5.12 SELECT LANGUAGE
- 5.13 SET UP SCAN
- 5.14 RADIO STATUS
- 5.15 RADIO MESSAGE
- 5.16 RADIO TEXTLINK
- 5.17 FAULTS/ALERTS
- 5.18 TONE ENCODE
- 5.19 ENCRYPTION
- 5.20 p25 conventional fallback
- 5.21 stealth mode
- 6. PROGRAMMING
- 7. REFERENCE
- 8. GLOSSARY
- 9. BASIC TROUBLESHOOTING
- 10. TECHNICAL ASSISTANCE
- 11. WARRANTY
14221-1850-2000, Rev. A
108
9.2 OTAR ERRORS/INFORMATION
WORKAROUNDS:
1. Zeroize.
2. Load proper KEK from the Harris Key Loader or Motorola KVL.
IF RADIO INDICATES:
1. INVALID KEYSTORE ZEROIZE NEEDED - This occurs if the radio’s keys were loaded by the Harris
Key Loader followed by an attempt to load UKEKs with the Key Loader or keys with the Motorola
KVL.
- Fix by performing workaround 1, followed by 2.
2. NO UKEK – Displayed during a zeroize performed from the radio or a zeroize initiated from the KMF.
- Fix by performing workaround 2.
3. Zeroize Complete – KMF has zeroized the radio.
- Fix by performing workaround 2.
4. Disabled OTAR Icon (red slash) – OTAR is disabled while in scan, talkaround, emergency, and
monitor.
- Fix by disabling these features. Icon will be corrected (no red slash).
5. Gray OTAR Icon (no red slash) – OTAR has not registered with tower (Conventional or Trunked
system).
- Fix by verifying proper frequencies.
- If the radio is turned to the OTAR channel out of range of a conventional tower, and then comes in
range after 3 minutes, fix by issuing an OTAR. Rekey, leave and re-enter the OTAR channel.
6. Green OTAR Icon – OTAR is registered, all is well.
- If update fails, verify you are in range of the tower and the KEK is correct.
7. Blue OTAR Icon – OTAR is attempting to rekey.
- If rekey fails, verify you are in range of the tower and the KEK is correct.