Operator's Manual
Table Of Contents
- 1. REGULATORY AND SAFETY INFORMATION
- 1.1 SAFETY SYMBOL CONVENTIONS
- 1.2 RF ENERGY EXPOSURE AWARENESS AND CONTROL INFORMATION FOR FCC OCCUPATIONAL USE REQUIREMENTS
- 1.3 COMPLIANCE WITH RF EXPOSURE STANDARDS
- 1.4 REGULATORY APPROVALS
- 1.5 OCCUPATIONAL SAFETY GUIDELINES AND SAFETY TRAINING INFORMATION
- 1.6 COMMON HAZARDS
- 1.7 SAFE DRIVING RECOMMENDATIONS
- 1.8 OPERATING RULES AND REGULATIONS
- 1.9 OPERATING TIPS
- 2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ
- 3. INTRODUCTION
- 4. BASIC OPERATION
- 4.1 RADIO CONTROLS
- 4.2 before first use
- 4.3 POWER ON AND SET VOLUME
- 4.4 vida® ID
- 4.5 RADIO DISPLAYS
- 4.6 STATUS MESsages
- 4.7 PREDEFINED MENU LAYOUTS
- 4.8 MENU
- 4.9 ALERT TONES
- 4.10 SELECT ZONE/SYSTEM
- 4.11 SELECT GROUP/CHANNEL
- 4.12 GROUP CALLS
- 4.13 INDIVIDUAL CALLS
- 4.14 USER PROFILES
- 4.15 NOISE CANCELLATION
- 4.16 VOICE ANNUNCIATION
- 4.17 ENABLE/DISABLE ENCRYPTION
- 4.18 CHANNEL GUARD (ANALOG CONVENTIONAL ONLY)
- 4.19 USE TALKAROUND TO BYPASS REPEATER (ANALOG AND P25 CONVENTIONAL ONLY)
- 4.20 CALL ALERT (PAGE)
- 4.21 TELEPHONE INTERCONNECT
- 4.22 DTMF
- 4.23 AUDIO PLAYBACK
- 4.24 START SCAN
- 4.25 STOP SCAN
- 4.26 MONITOR AND SQUELCH TYPES (CONVENTIONAL ONLY)
- 4.27 NUISANCE DELETE
- 4.28 Failsoft (P25 Trunked)
- 4.29 EMERGENCY OPERATION
- 4.30 MDC-1200 (ANALOG CONVENTIONAL ONLY)
- 5. ADVANCED OPERATIONS
- 5.1 VIEW/CHANGE PERSONALITIES
- 5.2 SITUATIONAL AWARENESS (SA) – P25 CONVENTIONAL ONLY
- 5.3 User Defined Zones
- 5.4 Mixed System Zone
- 5.5 CH INFO MENU
- 5.6 AUDIO SETTINGS
- 5.7 DISPLAY SETTINGS
- 5.8 GPS SETTINGS
- 5.9 POSITION INFO
- 5.10 BLUETOOTH
- 5.11 CLOCK SETTINGS
- 5.12 SELECT LANGUAGE
- 5.13 SET UP SCAN
- 5.14 RADIO STATUS
- 5.15 RADIO MESSAGE
- 5.16 RADIO TEXTLINK
- 5.17 FAULTS/ALERTS
- 5.18 TONE ENCODE
- 5.19 ENCRYPTION
- 5.20 p25 conventional fallback
- 5.21 stealth mode
- 6. PROGRAMMING
- 7. REFERENCE
- 8. GLOSSARY
- 9. BASIC TROUBLESHOOTING
- 10. TECHNICAL ASSISTANCE
- 11. WARRANTY
14221-1850-2000, Rev. A
38
4.10 SELECT ZONE/SYSTEM
A System is a group of channels or talkgroups that share a common set of parameters as programmed using
RPM2. For example, a Trunking system defines the parameters needed to communicate on an infrastructure
by agency or geographical region, such as WACN, System ID, Talkgroups, etc. A conventional system
defines the channel set used and any specific signaling attributes. Systems are designated by the XX icon
in the Zone/System menu.
A Zone is an OPTIONAL container that can hold channels or talkgroups from a variety of systems. In other
words, each member of a Zone belongs to an underlying system. Zones are always listed first in the
Zone/System menu and are designated by the icon. A button on the control head or KMM can be
programmed to scroll through available zones/systems (see Section 6.4).
If enabled via radio programming, systems are not displayed in the ZONE menu, only
zones are displayed.
Or
To select a zone/system via the menu:
1. Press the Menu button.
2. Navigate to the ZONE menu. The currently selected zone/system will be highlighted. A personality
can have up to 512 systems and up to 250 Zones.
3. Scroll up or down to highlight the desired zone/system. The up and down buttons may be held to scroll
repetitively, and the menu will wrap to allow quick access to a zone/system,
4. Press the VIEW ZONE soft key to view channels in the zone/system or select the desired zone/system
using the Group/Channel Select Knob.
NOTE