Operator's Manual
Table Of Contents
- 1. REGULATORY AND SAFETY INFORMATION
- 1.1 SAFETY SYMBOL CONVENTIONS
- 1.2 RF ENERGY EXPOSURE AWARENESS AND CONTROL INFORMATION FOR FCC OCCUPATIONAL USE REQUIREMENTS
- 1.3 COMPLIANCE WITH RF EXPOSURE STANDARDS
- 1.4 REGULATORY APPROVALS
- 1.5 OCCUPATIONAL SAFETY GUIDELINES AND SAFETY TRAINING INFORMATION
- 1.6 COMMON HAZARDS
- 1.7 SAFE DRIVING RECOMMENDATIONS
- 1.8 OPERATING RULES AND REGULATIONS
- 1.9 OPERATING TIPS
- 2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ
- 3. INTRODUCTION
- 4. BASIC OPERATION
- 4.1 RADIO CONTROLS
- 4.2 before first use
- 4.3 POWER ON AND SET VOLUME
- 4.4 vida® ID
- 4.5 RADIO DISPLAYS
- 4.6 STATUS MESsages
- 4.7 PREDEFINED MENU LAYOUTS
- 4.8 MENU
- 4.9 ALERT TONES
- 4.10 SELECT ZONE/SYSTEM
- 4.11 SELECT GROUP/CHANNEL
- 4.12 GROUP CALLS
- 4.13 INDIVIDUAL CALLS
- 4.14 USER PROFILES
- 4.15 NOISE CANCELLATION
- 4.16 VOICE ANNUNCIATION
- 4.17 ENABLE/DISABLE ENCRYPTION
- 4.18 CHANNEL GUARD (ANALOG CONVENTIONAL ONLY)
- 4.19 USE TALKAROUND TO BYPASS REPEATER (ANALOG AND P25 CONVENTIONAL ONLY)
- 4.20 CALL ALERT (PAGE)
- 4.21 TELEPHONE INTERCONNECT
- 4.22 DTMF
- 4.23 AUDIO PLAYBACK
- 4.24 START SCAN
- 4.25 STOP SCAN
- 4.26 MONITOR AND SQUELCH TYPES (CONVENTIONAL ONLY)
- 4.27 NUISANCE DELETE
- 4.28 Failsoft (P25 Trunked)
- 4.29 EMERGENCY OPERATION
- 4.30 MDC-1200 (ANALOG CONVENTIONAL ONLY)
- 5. ADVANCED OPERATIONS
- 5.1 VIEW/CHANGE PERSONALITIES
- 5.2 SITUATIONAL AWARENESS (SA) – P25 CONVENTIONAL ONLY
- 5.3 User Defined Zones
- 5.4 Mixed System Zone
- 5.5 CH INFO MENU
- 5.6 AUDIO SETTINGS
- 5.7 DISPLAY SETTINGS
- 5.8 GPS SETTINGS
- 5.9 POSITION INFO
- 5.10 BLUETOOTH
- 5.11 CLOCK SETTINGS
- 5.12 SELECT LANGUAGE
- 5.13 SET UP SCAN
- 5.14 RADIO STATUS
- 5.15 RADIO MESSAGE
- 5.16 RADIO TEXTLINK
- 5.17 FAULTS/ALERTS
- 5.18 TONE ENCODE
- 5.19 ENCRYPTION
- 5.20 p25 conventional fallback
- 5.21 stealth mode
- 6. PROGRAMMING
- 7. REFERENCE
- 8. GLOSSARY
- 9. BASIC TROUBLESHOOTING
- 10. TECHNICAL ASSISTANCE
- 11. WARRANTY
14221-1850-2000, Rev. A
49
applies to both Analog and P25 Conventional systems. It optionally allows the radio to also play the same
tone when it receives a call while operating in simplex or talkaround. If configured, the radio plays the
tone at the selected volume level.
The tone will not play on systems configured with MDC.
Talkaround Indication can be specified for each individual Analog and P25 Conventional system configured
in the personality. The following options can be selected, and apply only when the radio is on a simplex
channel or when talkaround has been enabled by the user:
• Disabled: (This is the default option.) When this option is selected, the radio plays the standard grant
tone when a call is placed. The radio does not play a tone when a call is received.
• Transmit Only: When this option is selected, the radio plays a different “talkaround” grant tone when
a call is placed. The radio does not play a tone when a call is received.
• Transmit and Receive: When this option is selected, the radio plays a different “talkaround” grant tone
when a call is placed, and at the beginning of a received call.
In the radio personality, the “Alert Tone” parameter needs to be enabled for each channel
on the Conventional Frequency Set. The “Ready to Talk Tone” parameter must also be
enabled for the Talk Around Indication tone to be played when the radio is keyed.
4.20 CALL ALERT (PAGE)
4.20.1 Send Alert
To send an alert:
1. Press the Menu button.
2. Navigate to the CALL menu.
3. Scroll up or down to highlight CALL ALERT and press the Group/Channel Select Knob.
4. Highlight the desired unit in the list and press the Group/Channel Select Knob, or select KEYPAD to
enter the Unit ID.
5. Press PTT to send the page.
NOTE
NOTE