Operator's Manual
Table Of Contents
- 1. REGULATORY AND SAFETY INFORMATION
- 2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ
- 3. CLASS I, DIVISION 2 OPTION
- 4. INTRODUCTION
- 5. BASIC OPERATION
- 5.1 RADIO CONTROLS
- 5.2 BEFORE FIRST USE
- 5.3 POWER ON AND SET VOLUME
- 5.4 VIDA ID
- 5.5 RADIO DISPLAYS
- 5.6 MANDOWN
- 5.7 STATUS MESSSAGES
- 5.8 PREDEFINED MENU LAYOUTS
- 5.9 MENU
- 5.10 ALERT TONES
- 5.11 SELECT ZONE/SYSTEM
- 5.12 SELECT GROUP/CHANNEL AND BANK
- 5.13 LOCK/UNLOCK KEYPAD
- 5.14 GROUP CALLS
- 5.15 INDIVIDUAL CALLS
- 5.16 USER PROFILES
- 5.17 NOISE CANCELLATION
- 5.18 PTT OPTIONS
- 5.19 VOICE ANNUNCIATION
- 5.20 ENABLE/DISABLE ENCRYPTION
- 5.21 TRANSMIT ENABLE/DISABLE
- 5.22 CHANNEL GUARD (ANALOG CONVENTIONAL ONLY)
- 5.23 USE TALKAROUND TO BYPASS REPEATER (ANALOG AND P25 CONVENTIONAL ONLY)
- 5.24 TYPE 99 OPERATION
- 5.25 CALL ALERT (PAGE)
- 5.26 TELEPHONE INTERCONNECT
- 5.27 DTMF
- 5.28 AUDIO PLAYBACK
- 5.29 START SCAN
- 5.30 STOP SCAN
- 5.31 MONITOR AND SQUELCH TYPES (CONVENTIONAL ONLY)
- 5.32 NUISANCE DELETE
- 5.33 FAILSOFT
- 5.34 EMERGENCY OPERATION
- 5.35 MDC-1200 (ANALOG CONVENTIONAL ONLY)
- 5.36 BEON OPERATION
- 5.37 STEALTH MODE
- 6. ADVANCED OPERATIONS
- 6.1 VIEW/CHANGE PERSONALITIES
- 6.2 SITUATIONAL AWARENESS (SA) – P25 CONVENTIONAL ONLY
- 6.3 USER-DEFINED ZONES/SYSTEMS
- 6.4 CH INFO MENU
- 6.5 AUDIO SETTINGS
- 6.6 DISPLAY SETTINGS
- 6.7 GPS SETTINGS
- 6.8 POSITION INFO
- 6.9 WI-FI
- 6.10 BLUETOOTH
- 6.11 CLOCK SETTINGS
- 6.12 BATTERY INFO
- 6.13 SELECT LANGUAGE
- 6.14 SET UP SCAN
- 6.14.1 Default, Priority 1, and Priority 2 Channels
- 6.14.2 Trunked/Conventional Scanning
- 6.14.3 Vote Scan (Analog and P25 Conventional Only)
- 6.14.4 Edit Scan List
- 6.14.5 Set or Remove Priority 1 and Priority 2 Channels
- 6.14.6 Custom Scan Lists
- 6.14.7 Wide Area System Scan (P25 Trunked and EDACS)
- 6.14.8 Site Lock
- 6.15 RADIO STATUS
- 6.16 RADIO MESSAGE
- 6.17 RADIO TEXTLINK
- 6.18 FAULTS/ALERTS
- 6.19 TONE ENCODE
- 6.20 ENCRYPTION
- 6.21 P25 CONVENTIONAL FALLBACK
- 6.22 EMERGENCY CHECK-IN TIMER
- 7. PROGRAMMING
- 8. REFERENCE
- 9. GLOSSARY
- 10. BASIC TROUBLESHOOTING
- 11. TECHNICAL ASSISTANCE
- 12. WARRANTY
14221-1800-2050
116
10.2 OTAR ERRORS/INFORMATION
WORKAROUNDS:
1. Zeroize.
2. Load proper KEK from the L3Harris Key Loader or Motorola KVL.
IF RADIO INDICATES:
1. INVALID KEYSTORE ZEROIZE NEEDED - This occurs if the radio’s keys were loaded by the
L3Harris Key Loader followed by an attempt to load UKEKs with the Key Loader or keys with
the Motorola KVL.
- Fix by performing workaround 1, followed by 2.
2. NO UKEK – Displayed during a zeroize performed from the radio or a zeroize initiated from
the KMF.
- Fix by performing workaround 2.
3. Zeroize Complete – KMF has zeroized the radio.
- Fix by performing workaround 2.
4. Disabled OTAR Icon (red slash) – OTAR is disabled while in scan, talkaround, emergency,
and monitor.
- Fix by disabling these features. Icon will be corrected (no red slash).
5. Gray OTAR Icon (no red slash) – OTAR has not registered with tower (Conventional or
Trunked system).
- Fix by verifying proper frequencies.
- If the radio is turned to the OTAR channel out of range of a conventional tower, and then
comes in range after 3 minutes, fix by issuing an OTAR. Rekey, leaving and re-enter the
OTAR channel.
6. Green OTAR Icon – OTAR is registered, all is well.
- If update fails, verify you are in range of the tower and the KEK is correct.
7. Blue OTAR Icon – OTAR is attempting to rekey.
- If rekey fails, verify you are in range of the tower and the KEK is correct.