Operator's Manual
Table Of Contents
- 1. REGULATORY AND SAFETY INFORMATION
- 2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ
- 3. CLASS I, DIVISION 2 OPTION
- 4. INTRODUCTION
- 5. BASIC OPERATION
- 5.1 RADIO CONTROLS
- 5.2 BEFORE FIRST USE
- 5.3 POWER ON AND SET VOLUME
- 5.4 VIDA ID
- 5.5 RADIO DISPLAYS
- 5.6 MANDOWN
- 5.7 STATUS MESSSAGES
- 5.8 PREDEFINED MENU LAYOUTS
- 5.9 MENU
- 5.10 ALERT TONES
- 5.11 SELECT ZONE/SYSTEM
- 5.12 SELECT GROUP/CHANNEL AND BANK
- 5.13 LOCK/UNLOCK KEYPAD
- 5.14 GROUP CALLS
- 5.15 INDIVIDUAL CALLS
- 5.16 USER PROFILES
- 5.17 NOISE CANCELLATION
- 5.18 PTT OPTIONS
- 5.19 VOICE ANNUNCIATION
- 5.20 ENABLE/DISABLE ENCRYPTION
- 5.21 TRANSMIT ENABLE/DISABLE
- 5.22 CHANNEL GUARD (ANALOG CONVENTIONAL ONLY)
- 5.23 USE TALKAROUND TO BYPASS REPEATER (ANALOG AND P25 CONVENTIONAL ONLY)
- 5.24 TYPE 99 OPERATION
- 5.25 CALL ALERT (PAGE)
- 5.26 TELEPHONE INTERCONNECT
- 5.27 DTMF
- 5.28 AUDIO PLAYBACK
- 5.29 START SCAN
- 5.30 STOP SCAN
- 5.31 MONITOR AND SQUELCH TYPES (CONVENTIONAL ONLY)
- 5.32 NUISANCE DELETE
- 5.33 FAILSOFT
- 5.34 EMERGENCY OPERATION
- 5.35 MDC-1200 (ANALOG CONVENTIONAL ONLY)
- 5.36 BEON OPERATION
- 5.37 STEALTH MODE
- 6. ADVANCED OPERATIONS
- 6.1 VIEW/CHANGE PERSONALITIES
- 6.2 SITUATIONAL AWARENESS (SA) – P25 CONVENTIONAL ONLY
- 6.3 USER-DEFINED ZONES/SYSTEMS
- 6.4 CH INFO MENU
- 6.5 AUDIO SETTINGS
- 6.6 DISPLAY SETTINGS
- 6.7 GPS SETTINGS
- 6.8 POSITION INFO
- 6.9 WI-FI
- 6.10 BLUETOOTH
- 6.11 CLOCK SETTINGS
- 6.12 BATTERY INFO
- 6.13 SELECT LANGUAGE
- 6.14 SET UP SCAN
- 6.14.1 Default, Priority 1, and Priority 2 Channels
- 6.14.2 Trunked/Conventional Scanning
- 6.14.3 Vote Scan (Analog and P25 Conventional Only)
- 6.14.4 Edit Scan List
- 6.14.5 Set or Remove Priority 1 and Priority 2 Channels
- 6.14.6 Custom Scan Lists
- 6.14.7 Wide Area System Scan (P25 Trunked and EDACS)
- 6.14.8 Site Lock
- 6.15 RADIO STATUS
- 6.16 RADIO MESSAGE
- 6.17 RADIO TEXTLINK
- 6.18 FAULTS/ALERTS
- 6.19 TONE ENCODE
- 6.20 ENCRYPTION
- 6.21 P25 CONVENTIONAL FALLBACK
- 6.22 EMERGENCY CHECK-IN TIMER
- 7. PROGRAMMING
- 8. REFERENCE
- 9. GLOSSARY
- 10. BASIC TROUBLESHOOTING
- 11. TECHNICAL ASSISTANCE
- 12. WARRANTY
14221-1800-2050
44
3. The radio rings and indicates a missed call if you do not respond. The ring sounds until you
press PTT, view the missed call menu using the up navigation button, change
channel/group/system, or power cycle the radio.
4. The radio can store up to ten (10) missed call entries. Select one of these entries to call the
unit back or press the DISMISS soft key to clear the entry.
5.16 USER PROFILES
XL Series radios support User Profiles (also referred to as “My Profile”). A User Profile is a
grouping of preset configurations that allow the user to change radio operation based on current
activity/scenario. For example, the radio can be programmed with profiles named Noisy, Fire, etc.,
and the radio user can switch profiles on the radio depending on the environment they are
entering. User Profile selection persists across system/group changes and power cycles. Up to
10 profiles can be programmed to the radio. When you activate a new personality, the selected
Profile changes to None.
A "Covert" Profile is installed on the radio by default. This profile cannot be modified or deleted.
The following attributes apply when the Covert profile is active:
• The speaker is enabled.
• All tones are disabled.
• Keypad tones are disabled.
• Voice Annunciation is disabled.
• The front display backlight is disabled.
• The top backlight is turned off.
• The indicator LED is disabled.
• All other attributes remain at their current value.
The radio keypad sequence LEFT-RIGHT-UP-DOWN can be used to exit Covert Mode.