Operator's Manual
Table Of Contents
- 1. REGULATORY AND SAFETY INFORMATION
- 2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ
- 3. CLASS I, DIVISION 2 OPTION
- 4. INTRODUCTION
- 5. BASIC OPERATION
- 5.1 RADIO CONTROLS
- 5.2 BEFORE FIRST USE
- 5.3 POWER ON AND SET VOLUME
- 5.4 VIDA ID
- 5.5 RADIO DISPLAYS
- 5.6 MANDOWN
- 5.7 STATUS MESSSAGES
- 5.8 PREDEFINED MENU LAYOUTS
- 5.9 MENU
- 5.10 ALERT TONES
- 5.11 SELECT ZONE/SYSTEM
- 5.12 SELECT GROUP/CHANNEL AND BANK
- 5.13 LOCK/UNLOCK KEYPAD
- 5.14 GROUP CALLS
- 5.15 INDIVIDUAL CALLS
- 5.16 USER PROFILES
- 5.17 NOISE CANCELLATION
- 5.18 PTT OPTIONS
- 5.19 VOICE ANNUNCIATION
- 5.20 ENABLE/DISABLE ENCRYPTION
- 5.21 TRANSMIT ENABLE/DISABLE
- 5.22 CHANNEL GUARD (ANALOG CONVENTIONAL ONLY)
- 5.23 USE TALKAROUND TO BYPASS REPEATER (ANALOG AND P25 CONVENTIONAL ONLY)
- 5.24 TYPE 99 OPERATION
- 5.25 CALL ALERT (PAGE)
- 5.26 TELEPHONE INTERCONNECT
- 5.27 DTMF
- 5.28 AUDIO PLAYBACK
- 5.29 START SCAN
- 5.30 STOP SCAN
- 5.31 MONITOR AND SQUELCH TYPES (CONVENTIONAL ONLY)
- 5.32 NUISANCE DELETE
- 5.33 FAILSOFT
- 5.34 EMERGENCY OPERATION
- 5.35 MDC-1200 (ANALOG CONVENTIONAL ONLY)
- 5.36 BEON OPERATION
- 5.37 STEALTH MODE
- 6. ADVANCED OPERATIONS
- 6.1 VIEW/CHANGE PERSONALITIES
- 6.2 SITUATIONAL AWARENESS (SA) – P25 CONVENTIONAL ONLY
- 6.3 USER-DEFINED ZONES/SYSTEMS
- 6.4 CH INFO MENU
- 6.5 AUDIO SETTINGS
- 6.6 DISPLAY SETTINGS
- 6.7 GPS SETTINGS
- 6.8 POSITION INFO
- 6.9 WI-FI
- 6.10 BLUETOOTH
- 6.11 CLOCK SETTINGS
- 6.12 BATTERY INFO
- 6.13 SELECT LANGUAGE
- 6.14 SET UP SCAN
- 6.14.1 Default, Priority 1, and Priority 2 Channels
- 6.14.2 Trunked/Conventional Scanning
- 6.14.3 Vote Scan (Analog and P25 Conventional Only)
- 6.14.4 Edit Scan List
- 6.14.5 Set or Remove Priority 1 and Priority 2 Channels
- 6.14.6 Custom Scan Lists
- 6.14.7 Wide Area System Scan (P25 Trunked and EDACS)
- 6.14.8 Site Lock
- 6.15 RADIO STATUS
- 6.16 RADIO MESSAGE
- 6.17 RADIO TEXTLINK
- 6.18 FAULTS/ALERTS
- 6.19 TONE ENCODE
- 6.20 ENCRYPTION
- 6.21 P25 CONVENTIONAL FALLBACK
- 6.22 EMERGENCY CHECK-IN TIMER
- 7. PROGRAMMING
- 8. REFERENCE
- 9. GLOSSARY
- 10. BASIC TROUBLESHOOTING
- 11. TECHNICAL ASSISTANCE
- 12. WARRANTY
14221-1800-2050
46
5.17.1 Enable Noise Cancellation
To enable Noise Cancellation:
1. Press the Menu/Select button to access the menu.
2. Press the left or right navigation buttons until the UTILITY menu is displayed.
3. Press the up or down navigation buttons to highlight AUDIO SETTINGS and press the
Menu/Select button.
4. Press the up or down navigation buttons to highlight NOISE CANCELLATION. Toggle Noise
Cancellation ENABLED/DISABLED using the Menu/Select button.
Refer to Section 6.5 for more information on the Audio Settings menu.
5.17.2 Using Noise Cancellation
When using the noise cancellation feature, observe the following:
• Verify NOISE CANCELLATION is enabled (see Section 5.17.1).
• Talk within two (2) inches of the primary microphone (see Figure 5-5).
• Ensure the primary and secondary microphones are not covered. See Section 5.17.4 for more
information on the primary and secondary microphones.
• Speak clearly, loudly, and with authority.
• In very noisy environments, it is o.k. to yell into the radio. The radio can handle loud input
levels.
Figure 5-5: Using Noise Cancellation