Operator's Manual
Table Of Contents
- 1. REGULATORY AND SAFETY INFORMATION
- 2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ
- 3. CLASS I, DIVISION 2 OPTION
- 4. INTRODUCTION
- 5. BASIC OPERATION
- 5.1 RADIO CONTROLS
- 5.2 BEFORE FIRST USE
- 5.3 POWER ON AND SET VOLUME
- 5.4 VIDA ID
- 5.5 RADIO DISPLAYS
- 5.6 MANDOWN
- 5.7 STATUS MESSSAGES
- 5.8 PREDEFINED MENU LAYOUTS
- 5.9 MENU
- 5.10 ALERT TONES
- 5.11 SELECT ZONE/SYSTEM
- 5.12 SELECT GROUP/CHANNEL AND BANK
- 5.13 LOCK/UNLOCK KEYPAD
- 5.14 GROUP CALLS
- 5.15 INDIVIDUAL CALLS
- 5.16 USER PROFILES
- 5.17 NOISE CANCELLATION
- 5.18 PTT OPTIONS
- 5.19 VOICE ANNUNCIATION
- 5.20 ENABLE/DISABLE ENCRYPTION
- 5.21 TRANSMIT ENABLE/DISABLE
- 5.22 CHANNEL GUARD (ANALOG CONVENTIONAL ONLY)
- 5.23 USE TALKAROUND TO BYPASS REPEATER (ANALOG AND P25 CONVENTIONAL ONLY)
- 5.24 TYPE 99 OPERATION
- 5.25 CALL ALERT (PAGE)
- 5.26 TELEPHONE INTERCONNECT
- 5.27 DTMF
- 5.28 AUDIO PLAYBACK
- 5.29 START SCAN
- 5.30 STOP SCAN
- 5.31 MONITOR AND SQUELCH TYPES (CONVENTIONAL ONLY)
- 5.32 NUISANCE DELETE
- 5.33 FAILSOFT
- 5.34 EMERGENCY OPERATION
- 5.35 MDC-1200 (ANALOG CONVENTIONAL ONLY)
- 5.36 BEON OPERATION
- 5.37 STEALTH MODE
- 6. ADVANCED OPERATIONS
- 6.1 VIEW/CHANGE PERSONALITIES
- 6.2 SITUATIONAL AWARENESS (SA) – P25 CONVENTIONAL ONLY
- 6.3 USER-DEFINED ZONES/SYSTEMS
- 6.4 CH INFO MENU
- 6.5 AUDIO SETTINGS
- 6.6 DISPLAY SETTINGS
- 6.7 GPS SETTINGS
- 6.8 POSITION INFO
- 6.9 WI-FI
- 6.10 BLUETOOTH
- 6.11 CLOCK SETTINGS
- 6.12 BATTERY INFO
- 6.13 SELECT LANGUAGE
- 6.14 SET UP SCAN
- 6.14.1 Default, Priority 1, and Priority 2 Channels
- 6.14.2 Trunked/Conventional Scanning
- 6.14.3 Vote Scan (Analog and P25 Conventional Only)
- 6.14.4 Edit Scan List
- 6.14.5 Set or Remove Priority 1 and Priority 2 Channels
- 6.14.6 Custom Scan Lists
- 6.14.7 Wide Area System Scan (P25 Trunked and EDACS)
- 6.14.8 Site Lock
- 6.15 RADIO STATUS
- 6.16 RADIO MESSAGE
- 6.17 RADIO TEXTLINK
- 6.18 FAULTS/ALERTS
- 6.19 TONE ENCODE
- 6.20 ENCRYPTION
- 6.21 P25 CONVENTIONAL FALLBACK
- 6.22 EMERGENCY CHECK-IN TIMER
- 7. PROGRAMMING
- 8. REFERENCE
- 9. GLOSSARY
- 10. BASIC TROUBLESHOOTING
- 11. TECHNICAL ASSISTANCE
- 12. WARRANTY
14221-1800-2050
77
6.10.3 Reconnecting to Covert Bluetooth Microphone 12082-0684-01
When powering down, the radio and the microphone should be turned off one at a time, allowing
the first device to completely shut down before turning off the second device.
Power Up Sequence:
1. Power up the XL radio. Wait for power up to complete.
2. Power up covert microphone 12082-0684-01.
3. Wait for Bluetooth connection as indicated by the LED. When connected, the LED is on and
blue.
4. If the microphone LED indicates Idle or does not connect, press and release the PTT button.
6.10.4 Pair with the SCOTT EPIC 3 Radio Direct Interface (RDI) Voice Amplifier
The RDI Voice Amplifier enhances SCBA voice intelligibility when connected to the XL-400P
Portable via Bluetooth.
To turn the amplifier on and place into pairing mode:
1. Press and hold the power button until the LED changes from green to red. This happens in
about four (4) seconds.
2. Release the power button.
3. The LED starts blinking indicating the amp is in pairing mode.
4. Ensure the LED is the same color blinking on and off indicating pairing mode. The amp will
timeout of pairing mode quickly and the blinking will stop. If this happens before successful
pairing, power off and restart from Step 1.
5. If the LED is blinking between light red and dark red, then the amp is in programming mode.
If you try to pair with the amplifier in this mode, it will identify itself as an RI version. Turn off
power and restart from step 1.
6.11 CLOCK SETTINGS
To view/change clock settings:
1. Press the Menu/Select button to access the main menu.
2. Press the left or right navigation buttons to display the UTILITY menu.
3. Press the up or down navigation buttons to highlight CLOCK SETTINGS and press the
Menu/Select button.