Operator's Manual
Table Of Contents
- 1. REGULATORY AND SAFETY INFORMATION
- 2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ
- 3. CLASS I, DIVISION 2 OPTION
- 4. INTRODUCTION
- 5. BASIC OPERATION
- 5.1 RADIO CONTROLS
- 5.2 BEFORE FIRST USE
- 5.3 POWER ON AND SET VOLUME
- 5.4 VIDA ID
- 5.5 RADIO DISPLAYS
- 5.6 MANDOWN
- 5.7 STATUS MESSSAGES
- 5.8 PREDEFINED MENU LAYOUTS
- 5.9 MENU
- 5.10 ALERT TONES
- 5.11 SELECT ZONE/SYSTEM
- 5.12 SELECT GROUP/CHANNEL AND BANK
- 5.13 LOCK/UNLOCK KEYPAD
- 5.14 GROUP CALLS
- 5.15 INDIVIDUAL CALLS
- 5.16 USER PROFILES
- 5.17 NOISE CANCELLATION
- 5.18 PTT OPTIONS
- 5.19 VOICE ANNUNCIATION
- 5.20 ENABLE/DISABLE ENCRYPTION
- 5.21 TRANSMIT ENABLE/DISABLE
- 5.22 CHANNEL GUARD (ANALOG CONVENTIONAL ONLY)
- 5.23 USE TALKAROUND TO BYPASS REPEATER (ANALOG AND P25 CONVENTIONAL ONLY)
- 5.24 TYPE 99 OPERATION
- 5.25 CALL ALERT (PAGE)
- 5.26 TELEPHONE INTERCONNECT
- 5.27 DTMF
- 5.28 AUDIO PLAYBACK
- 5.29 START SCAN
- 5.30 STOP SCAN
- 5.31 MONITOR AND SQUELCH TYPES (CONVENTIONAL ONLY)
- 5.32 NUISANCE DELETE
- 5.33 FAILSOFT
- 5.34 EMERGENCY OPERATION
- 5.35 MDC-1200 (ANALOG CONVENTIONAL ONLY)
- 5.36 BEON OPERATION
- 5.37 STEALTH MODE
- 6. ADVANCED OPERATIONS
- 6.1 VIEW/CHANGE PERSONALITIES
- 6.2 SITUATIONAL AWARENESS (SA) – P25 CONVENTIONAL ONLY
- 6.3 USER-DEFINED ZONES/SYSTEMS
- 6.4 CH INFO MENU
- 6.5 AUDIO SETTINGS
- 6.6 DISPLAY SETTINGS
- 6.7 GPS SETTINGS
- 6.8 POSITION INFO
- 6.9 WI-FI
- 6.10 BLUETOOTH
- 6.11 CLOCK SETTINGS
- 6.12 BATTERY INFO
- 6.13 SELECT LANGUAGE
- 6.14 SET UP SCAN
- 6.14.1 Default, Priority 1, and Priority 2 Channels
- 6.14.2 Trunked/Conventional Scanning
- 6.14.3 Vote Scan (Analog and P25 Conventional Only)
- 6.14.4 Edit Scan List
- 6.14.5 Set or Remove Priority 1 and Priority 2 Channels
- 6.14.6 Custom Scan Lists
- 6.14.7 Wide Area System Scan (P25 Trunked and EDACS)
- 6.14.8 Site Lock
- 6.15 RADIO STATUS
- 6.16 RADIO MESSAGE
- 6.17 RADIO TEXTLINK
- 6.18 FAULTS/ALERTS
- 6.19 TONE ENCODE
- 6.20 ENCRYPTION
- 6.21 P25 CONVENTIONAL FALLBACK
- 6.22 EMERGENCY CHECK-IN TIMER
- 7. PROGRAMMING
- 8. REFERENCE
- 9. GLOSSARY
- 10. BASIC TROUBLESHOOTING
- 11. TECHNICAL ASSISTANCE
- 12. WARRANTY
14221-1800-2050
82
6.14.5 Set or Remove Priority 1 and Priority 2 Channels
Priority channels are scanned more often than non-priority channels. Note that P1 and P2 can
only be set if configured as “Keypad” and the scan list is not set to “Fixed” using RPM2.
To set or remove priority 1 and priority 2 channels:
1. Press the Menu/Select button.
2. Press the left or right navigation buttons to display the SCAN menu.
3. Press the up or down navigation buttons to highlight SCAN LISTS and press the Menu/Select
button.
4. Press the up or down navigation buttons to highlight the desired scan list and press the
Menu/Select button.
5. Press the up or down navigation buttons to highlight the desired channel/group.
6. Select OPTIONS.
7. Press the up or down navigation buttons to highlight SET PRI1 or SET PRI2 and press the
Menu/Select button. A Priority 1 channel appears with a P1; a Priority 2 channel appears with
a P2.
8. Select REMOVE PRI to remove priority.