REPORT NO : HCT-F04-1004 FCC ID : O5XHP-500B DATE : OCTOBER 18, 2004 ATTACHMENT E-2. - USER’S MANUAL(2) HYUNDAI CALIBRATION & CERTIFICATION TECHNOLOGIES CO., LTD. SAN 136-1, AMI-RI , BUBAL-EUP, ICHEON-SI,KYOUNKI-DO, 467-701,KOREA TEL : +82 31 639 8518 FAX : +82 31 639 8525 www.hctec.co.
Monitor Installation 3 1. Shown as left, carefully place the monitor screen side down on a cushioned surface that will protect the monitor and screen from damage. 2. Insert the monitor brackets on the monitor shown as left. Install the 4 bolts securely, in the back of the monitor in the holes provided. Be sure the bracket hooks are at the top side of the monitor. (for 42" PDP) 4 1.
Monitor Installation Wall Mount Accessories ANCHOR 8EA SCREW 8EA BOLT 6EA M8 x 30L BOLT 6EA M4 x 6L OWNER'S MANUAL 19
Monitor Installation Table Stand Installation (optional) < The Monitor can be installed on the desk as shown above. > • Table Stand mount minimum allowable clearances for adequate ventilation. 1.18inch 4inch 4inch 4inch 2.
Monitor Installation Installation (Separate Type) OWNER'S MANUAL 21
Monitor Installation Installation (United Type) 22 OWNER'S MANUAL
Monitor Installation Speaker Installation (optional) 42" Speaker Installation (Optional) • Be sure monitor power is turned off before making any connections. Place the speakers in the position you want. Install the speaker wires on the monitor and speaker. Be sure to connect the positive "+" wire to the "+" input and the negative "-" wire to the "-" input. Connect left monitor input to left speaker and right monitor input to right speaker.
Monitor Installation Speaker Accessories 4-Iron Plates (Mount speakers to monitor) 8-4 x 8 Short Bolts (Attach iron plates to monitor) 24 OWNER'S MANUAL 8-4 x 16 Long Bolts (Attach iron plates to speakers) 2-Speaker Wires
Monitor Installation 50" Speaker Installation (Optional) • Match red to red, black to black of speaker / TV • Be sure monitor power is turned off before making any connections. Place the speakers in the position you want. Install the speaker wires on the monitor and speaker. Be sure to connect the positive "+" wire to the "+" input and the negative "-" wire to the "-" input. Connect left monitor input to left speaker and right monitor input to right speaker.
Monitor Installation Speaker Accessories 4-Iron Plates (Mount speakers to monitor) 8-4 x 8 Short Bolts (Attach iron plates to monitor) 26 OWNER'S MANUAL 8-4 x 16 Long Bolts (Attach iron plates to speakers) 2-Speaker Wires
Watching TV To watch TV 1 Connect the TV antenna cable to the TV input jack. Press INPUT button on the remote control and select TV on OSD. 2 Use CH+, CH- button or numeric button to change TV channel for your channel selection. 3 Press Pre.CH button on the remote control to tune the previous channel. 4 Also, you can tune to cable service provided channels using the cable box. For further information regarding cable TV service, contact cable TV service provider(s).
Watching VCR How to connect With S-Video Connect a S-Video cable to the S-Video jacks of the VCR and the PDP. Connect L (White), R (Red) sound cable (composite) to the sound jacks of the VCR and the PDP. With AV input Connect a composite cable to the AV video jacks of the VCR and the PDP. Connect L (White), R (Red) sound cable (composite) to the sound jacks of the VCR and the PDP. To watch VCR 1 Press INPUT button on the remote control and select Video Sources.
Watching DVD How to connect • Connect the three separate component video cables to the DVD player's Y, Pb and Pr jacks and to the Component jacks on the PDP. • Connect the audio cable to the DVD player's audio L (White) and R (Red) jacks and to the L and R audio jacks beside the Component jacks on the PDP. How to use 1 Turn on the DVD player. 2 Press INPUT button on the remote control of the PDP and select Component1 or Component2.
Watching Set Top Box How to connect Connect Set Top Box video inputs to SCART, COMPONENT, PC or DVI jacks on the PDP. Audio inputs to Audio sockets beside the L (White) and R (Red) audio jacks which you connect video inputs. How to use 1 Turn on the Set Top Box. 2 Press INPUT button on the remote control of the PDP and select Component1, Component2, PC or DVI.
Connecting The PC (D-Sub and DVI) Connecting a PC to the PDP • There are two connectors to connect the PDP and PC: D-Sub and DVI. • D-Sub Connect a PC (15pin) video cable between the Video Output port on the PC and the PC port on the PDP. • DVI Connect a DVI-D cable between the DVI Output port on the PC and the DVI port on the PDP. Pin Configuration 15Pin Signal Cable (based on protruded pin) To watch the PC screen 1 Turn on the PDP and press INPUT button to select the PC MODE.
Displayable Monitor Specification Resolution 640 x 350 640 x 400 640 x 480 800 x 600 Horizontal Frequency (KHz) Vertical Frequency (Hz) 31.468 70.09 37.861 85.08 31.469 70.08 37.927 85.03 31.469 59.94 35.000 66.66 37.861 72.80 37.500 75.00 43.269 85.00 45.913 90.03 53.011 100.04 64.062 120.000 35.156 56.25 37.879 60.31 48.077 72.18 46.875 75.00 53.674 85.06 56.000 90.00 64.016 100.00 832 x 624 49.725 74.55 852 x 480 31.468 60.05 48.363 60.00 56.476 70.
Basic Operation Turning PDP TV On / Off Press the Power button on the remote control. The PDP will turn on and you will be ready to use its features. You can also use the Power button on the front panel. Select Source Press INPUT button on the remote control. Then you can see the source list menu shown as below. Source Change 1 TV 2 AV 1 3 AV 2 4 S-VIDEO /AV 3 Select the source to watch with CH+/CH- button on the remote control and press the Menu/Set button.
OSD Menu Structure • OSD (On Screen Display) allows users to control or adjust various features and settings in accordance with his/her preferences. • Press the Menu/Set button on the remote control to see the main OSD menu. EXAMPLE of OSD Menu Pictute Mode Standard Temparature Normal Video NR Screen Format 1 OFF 16 : 9 Main Menu Press Menu/Set button on the remote control to enter the main OSD menu. First, select Main menu item you need with CH+/CH- key.
CHANNEL (TV) Channel Type Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e., an antenna, a standard cable system, an HRC, or an IRC). 1 Press Menu/set button to display the main OSD menu. 2 Select the TV main menu item. 3 Press Menu/Set to enter the sub menu. 4 Select Channel Type and press VOL+ button to enter the ¥ parts. Then the cursor moves into the ¥ parts.
CHANNEL (TV) Auto Scan 1 Press Menu/set button to display the main OSD menu. 2 Select the TV Main menu. Auto Scan 3 Press Menu/Set to enter the sub menu. Fine Tune 4 Select Auto Scan with CH+/CH- button and press Menu/Set button on the remote control. Then the tuning bar will appear and scanning will start. Auto Scan Channel Type CH UHF ¥ CATV ¥ CATV 5 16 • Only scanned channels can be stored as Favorite channels.
CHANNEL (TV) Set the favorite channel You can store of your favorite channels for each available input source (such as TV or CATV). Then, when you press the FAVORITE button on the remote control, the PDP display only the favorite channels you previously stored, allowing you to quickly and easily find frequently wanted channels. 1 Press Menu/set button to display the main OSD menu. 2 Select the TV main menu. Auto Scan 3 Press Menu/Set to enter the TV sub menu.
CHANNEL (TV) Digest In the Digest function, you can watch 9 programs at the same time. (This function works only in TV mode) 1 Press the Digest button on the Remote Control. 2 By pressing the channel number, the selected channel becomes main window. 3 You can make off the Digest Function by pressing Digest button again. Only memorized channels can be displayed in the Digest Function. 15 windows are available for 50" and 63" Plasma TV.
PICTURE Mode Your PDP has 3 automatic factory preset picture settings (“Standard”, “Vivid” and “Mild”). You can choose Standard, Vivid or Mild by pressing “Picture” button on the remote control (or by making a selection from the menu). Or you can select USER which automictically recalls your personalized picture setting. 1 Press Menu/set button to display the main OSD menu. 2 Select the picture main menu. 3 Press Menu/Set to enter the sub menu. 4 Select Mode and press Menu/Set to enter the sub menu.
PICTURE Picture Mode is to set CH+ or adjust Picture Adjust, Mode, Video Noise Reduction, Screen Format and Burn Protection. Adjust USER Mode You can change the Contrast, Brightness, Color, and Sharpness according to personal preference in USER mode. 1 Select the item to adjust with CH-, CH+ button. 2 Press Menu/Set button. 3 Adjust the item with VOL-, VOL+ button. 4 To cancel all adjust, select Recall and press Menu/Set button.
PICTURE Contrast Adjust brightness difference between bright part of the screen and dark part. Distinct Vague Dark Bright Decrease Increase Less sharp Sharp Brightness Adjust brightness of the screen. Color Adjust deep and light color of the screen. Sharpness Adjust vividness of the screen.
PICTURE Temperature Your PDP has 5 screen temperatures (color settings): Mode Temparature Normal ¥ OFF 1 Press Menu/set button to display the main OSD menu. Video NR 2 Select the picture main menu. Screen Format 3 Press Menu/Set to enter the picture menu. 4 Select Temperature and press Menu/Set to enter the under menu. Then the Picture-Temperature under menu appear. 5 Select the Temperature mode with CH-/CH+ button and press Menu/Set button. 6 Press BACK button to return.
PICTURE Video NR This function automatically filters out and reduces the image noise and improves picture quality where receiving weak signals. 1 Press Menu/Set button to display the main OSD menu. 2 Select the picture main menu item. Temparature Normal 3 Press Menu/Set to enter the sub menu. Video NR ¥ OFF 4 Select Video NR and press VOL+ button to enter the ¥ parts. Then the cursor moves into the ¥ parts. 5 Turn on or off Video NR function with CH+/CHbutton and press BACK button.
PICTURE Screen Format Your PDP has four Screen Formats: 16:9, PANORAMA, ZOOM1, ZOOM2, 4:3. (For more detail description for these modes, refer to the next page.) 1 Press Menu/Set button to display the main OSD menu. 2 Select the picture main menu. Temparature 3 Press Menu/Set to enter the picture menu. Video NR 4 Select Screen Format and press Menu/Set to enter the under menu. Then the Screen Format under menu appear. 5 Select the screen format you want and press Menu/Set button.
PICTURE Screen Format Description 16 : 9 16:9 video: No change. 4:3 video: Expands 4:3 video signal horizontally to fit the 16 : 9 screen. Panorama 16:9 video: No change. 4:3 video: Expands 4:3 video horizontally to fit the 16 : 9 screen and to minimize distortion, sides are expanded more than center. Zoom 1 Expands 16 : 9 mode screen vertically. Zoom 2 Expands zoom 1 mode screen vertically. 4:3 16:9 video: The image is suppressed. 4:3 video: No expansion. There are gray areas besides the image.
PICTURE ( PC ) In PC mode, you can adjust the H,V-Position, Native Mode, Native H-Size and Phase. Also you can adjust them automatically. Geometry You can change H, V-Position, Native Mode, Native H-Size and Phase in PC mode like usual PC monitors. You can also adjust them automatically. (Auto adjust function.) 1 Press Menu/set button to display the main OSD menu. 2 Select the picture main menu with CH+, CH- button. Temperature 3 Press Menu/Set to enter the sub menu.
PICTURE ( PC ) H-POSITION V-POSITION PHASE Mismatch Match OWNER'S MANUAL 47
SOUND In SOUND Menu, you can adjust balance, MTS ( Multi-Track Sound), AVC (Auto Volume Control) and select the equalizer settings. Balance This control allows you to adjust the balance of the left and right speaker output. 1 Press Menu/set button to display the main OSD menu. 2 Select the SOUND main menu. 3 Press Menu/Set to enter the sub menu. 4 Select Balance and press Menu/Set button. 5 Ajust the balance with VOL-, VOL+ button and press Menu/Set button.
SOUND Sound Mode Your PDP has four automatic sound settings ("Standard", "Movie", "Music" and "News") that are preset at the factory. You can activate either Standard, Movie, Music or News by pressing "SOUND" on the remote control (or by making a selection from the menu) or you can select "Custom" which automatically recalls your personalized sound settings. 1 Press Menu/set button to display the main OSD menu. 2 Select the SOUND main menu. 3 Press Menu/Set button to enter the sub menu.
SOUND User Adjust You can use the OSD menu to change the Treble, Bass, Balance and DRC according to your preference. 1 Equalizer menu appear when you select USER mode. 2 Select a gain bar with VOL+, VOL- button on the remote control and adjust it with CH+/CH- button. 3 Press BACK or BACK button on the remote control to exit Equalizer. The result will be saved automatically. Select USER mode (Previous page) Equalizer 0.1 0.5 1.5 5.0 10.0kHz MTS Select sound signal format from the input source.
SET UP Source in PIP Change the source of the PIP window. 1 Select Source and press Menu/Set to enter the sub menu. Then the PIP sub menu appear. 2 The available sources will be displayed. Select the source and press Menu/Set button. Size ¥ SMALL Source Picture Swap Position TV AV 1 This picture is an example. The displayed sources may be different depending on the main input source.
SET UP In SET UP menu, you can adjust the transparency of the OSD menu and set PIP and others. Translucent Adjust the transparency of the OSD menu. There are 8 step from OFF to 7. 1 Press Menu/set button to display the main OSD menu. 2 Select the SET UP main menu with CH+/CHbutton on the remote control. 3 Press Menu/Set to enter the sub menu. 4 Select Translucent and press VOL+ button to enter the ¥ parts. Then the cursor moves into the ¥ parts.
SET UP PIP (Picture In Picture) You can watch two channels or sources at the same time. And set up PIP size and position. 1 Press Menu/set button to display the main OSD menu. 2 Select the SET UP main menu with CH+/CH- button on the remote control. 3 Press Menu/Set to enter the sub menu. 4 Select PIP and press Menu/Set to enter the sub menu. Then the PIP sub menu appear.
SET UP Position in PIP Change the position of the PIP window. 1 2 Select Position with CH+/CH- button on the remote control and press Menu/Set to enter the sub menu. Then the PIP sub menu appear. In Sub Menu, there are four positions. Select the position with CH+/CH- button on the remote control and press BACK button.
SET UP Advanced You can se up ID, Burn Protect, Burn Clear, Blue Back, Language and Child Lock in Advanced Menu. 1 Press Menu/set button to display the main OSD menu. 2 Select the SET UP main menu with CH+ / CHbutton on the remote control. 3 Press Menu/Set to enter the sub menu. 4 Select Advanced and press Menu/Set to enter the Advanced menu. Then the Advanced sub menu appear.
SET UP Burn Protect in Advanced PDP may be damaged from displaying a static image long time (over 30 minute). It is called as image sticking, and Burn protect function moves image regularly to relieve image sticking. You can set the moving range of the Burn Protection function ( How much the image will move. ). Burn Protection function moves image 1 pixel per 2 minute, and after moving the set range, image starts to go back to the original position.
SET UP Language in Advanced Set the language to use in OSD. Supported languages are English, French, German, Spanish, Italian. 1 2 Select Language and press VOL+ button to enter the ¥ parts. Then the cursor moves into the ¥ parts. Choose the Language with CH+ / CH- button and press BACK button. Set ID ¥ 99 Burn Protect ¥ ON Burn Clear ¥ OFF Blue Back ¥ OFF Language ¥ ENGLISH Child Lock ¥ OFF Child Lock in Advanced Lock the OSD panel of the PDP monitor.
SET UP V-Chip (TV parental Guidelines) Parental restrictions can be set up using either of two methods: The TV guidelines or the MPAA rating. 1 Press Menu/set button to display the main OSD menu. 2 Select the SET UP main menu with CH+/CHbutton on the remote control. 3 Press Menu/Set to enter the sub menu. 4 After enter the password, the V-Chip sub menu appear.
SET UP TV Blocking in V-Chip You can set up Restrictions Using the "TV Parental Guidelines" of FCC. 1 2 3 Select TV Blocking with CH+/CH- button on the remote control and press Menu/Set to enter the sub menu. Then the TV Blocking sub menu appear. You can independently lock the TV ratings. The locked TV (FCC) ratings are indicated by the symbol .
SET UP Change Password in V-Chip 1 2 Select Change Password with CH+/CH- button on the remote control and press Menu/Set to enter the sub menu. Then the Pass Word change sub menu appear. Enter the new password with numeric buttons on the remote control. TV Blocking Movie Blocking Change Password V-Chip Bocking ¥ OFF Pass Word ____ V-Chip Blocking in V-Chip 60 1 Select V-Chip Blocking with CH+/CH- buttons on the remote control. 2 Enter to the ¥ part by pressing VOL+ button.
TIME In the TIME menu, you can set the current time and auto power on / off. Time Set Set the current time. 1 Press Menu/set button to display the main OSD menu. 2 Time Set AM 03:29 Select the TIME main menu. On Time AM 05:11 ON 3 Press Menu/Set to enter the sub menu. On Channel ¥ 99 On Volume ¥ 100 4 Select Time Set by pressing VOL+ button. Off Time 5 Move the cursor by pressing VOL-, VOL+ button and adjust time by CH+, CH- button.
TIME On Channel Set the channel when PDP power turn on automatically. • Available only when the Time is set and On Time is ON. 1 Press Menu/set button to display the main OSD menu. 2 Select the TIME main menu with CH+/CH- button on the remote control. Time Set AM 03:29 On Time AM 05:11 ON On Channel ¥ 99 ¥ 100 3 Press Menu/Set to enter the sub menu. On Volume 4 Select On Channel. Off Time 5 Enter to the ¥ part with VOL+ button. Then the cursor moves into the ¥ parts.
TIME Off Time This PDP can be set to turn off automatically at specific times that you choose. Before using the timer, you must set the PDP's clock as described previously. 1 Press Menu/set button to display the main OSD menu. 2 Select the TIME main menu with CH+/CH- button on the remote control. 3 Press Menu/Set to enter the sub menu. 4 Select Off Time with CH+/CH- button on the remote control and press VOL+ button.
Viewing the Picture-in-Picture Move key : Move the position of PIP window. Left Up Right Up (Start) Left Down Right Down Swap key : Swap the sources of the main screen and PIP window. MODE KEY : Change the PIP window mode. OFF ➔ SMALL ➔ LARGE ➔ TWIN LARGE SMALL TWIN Source key : Change the source of the PIP window. The available sources are shown as below.
Specification – 40 Inch LCD (1) Function and Display Specification Display Size 40-Inch 15 : 9 Diagonal Screen Display Mode Variable 4 Modes (4:3 Mode/ 16:9 X 3 Modes) Pixel Format 1280x768 Physical Pixel Contrast Ratio 600:1 Brightness 450 cd/㎡ Resolution (RGB) 1280 X 768 / 50,60Hz PIP Advanced multi-windows viewing PIP(picture in picture) with four selectable window positions on Video mode Input compatible Multiple input compatible Video Advanced motion digital / Motion-Adaptive De-interlac
Specification – 40 Inch LCD (2) Power Consumption Input Power AC 100 ~ 240V 50/60Hz Power consumption 300 Watt Connectivity TV1,2 Input RF/CATV (PAL/SECAM) Scat1,2 Input SCART X 2Port (SCART1 (HALF), SCART2 (FULL)) Composite Input/Output RCA X 2Port (AV INPUT, AV OUTPUT) Component1,2 Input RCA X 2Port (Y, Pb/Cb, Pr/Cr : 480i, 480p, 576i, 576p, 720p, 1080i) S-Video Input Mini Din 4Pin X 1Port PC Input Mini D-Sub 15Pin X 1Port / HDTV Input(480i, 480p, 576i, 576p, 720P, 1080i) DVI Input Mini D
Specification 42" Plasma TV Display Panel Function and Display Specification Display Size 42-Inch 16 : 9 Diagonal Screen Display Mode Variable 4 Modes (4:3 Mode / 16:9 X 3 Modes) Pixel Format 852 X 480 Physical Pixel Contrast Ratio 3000 : 1 Brightness 1000 cd/m 2 Resolution (RGB) 1280 X 1024 / 60Hz PIP Advanced multi-windows viewing PIP(picture in picture) with four selectable window positions on Video mode.
Specification 50" Plasma TV Display Panel Function and Display Specification Display Size 50-Inch 16 : 9 Diagonal Screen Display Mode Variable 4 Modes (4:3 Mode / 16:9 X 3 Modes) Panel Pixel Format 1366 X 768 Physical Pixel Contrast Ratio 900:1 Brightness 800 cd/m 2 Max Resolution (RGB) 1280 X 1024 / 60Hz PIP Advanced multi-windows viewing PIP(picture in picture) with four selectable window positions on Video mode.
Specification 63" Plasma TV Display Panel Function and Display Specification Display Size 63-Inch 16 : 9 Diagonal Screen Display Mode Variable 4 Modes (4:3 Mode / 16:9 X 3 Modes) Panel Pixel Format 1366 X 768 Physical Pixel Contrast Ratio 1000:1 Brightness 800 cd/m 2 Max Resolution (RGB) 1280 X 1024 / 60Hz PIP Advanced multi-windows viewing PIP(picture in picture) with four selectable window positions on Video mode.
Troubleshooting Before you call a service technician, please scan this list of problems and possible solutions. It may save you time and money. Problem No picture & No sound Quick Action for Possible Solution • Check whether the Monitor is turned on. • Power cord inserted into wall outlet? • Plug another product's power cord into the wall outlet where the Monitor's power cord was plugged in. Picture OK & No sound • Press the VOLUME() button. • Check the audio input signal.
Warranty Card 1-Year Limited Warranty Warranty Service is only available in the country of original purchase. This is an impor tant document. Attach your bill of sale to this card and keep it in a safe place. Your bill of sale is your warranty. Our warranty remains in effect for one year from the date of the first consumer purchase.
Memo 70 OWNER'S MANUAL
