User Manual

6 - English
NOTE: Runningatlowspeedsunderconstantusagemay
causethedrilltobecomeoverheated.Ifthisoccurs,cool
thedrillbyrunningitwithoutaloadandatfullspeed.
DIRECTION OF ROTATION SELECTOR
(FORWARD/REVERSE/CENTER LOCK)
See Figure 2, page 10 (HPDD01).
See Figure 2, page 11 (HPID01)
Set the direction of rotation selector in the OFF (center
lock)positiontolocktheswitchtriggerandhelpprevent
accidentalstartingwhennotinuse.
Positionthedirectionofrotationselectortotheleftofthe
switchtriggerforforwarddrilling.Positiontheselectorto
therightoftheswitchtriggertoreversethedirection.
NOTE: Thedrillwillnotrununlessthedirectionofrotation
selectorispushedfullytotheleftorright.
NOTICE:
To prevent gear damage, always allow the chuck to
cometoacompletestopbeforechangingthedirection
of rotation.
WARNING:
Battery tools are always in operating condition. Lock
the switch when not in use or carrying at your side,
wheninstallingorremovingthebatterypack,andwhen
installingorremovingbits.
INSTALLING/REMOVING BATTERY PACK
See Figure 1, page 10 (HPDD01).
See Figure 1, page 11 (HPID01).
Tolocktheswitchtrigger,placethedirectionofrotation
selectorinthecenterposition.
Insertthebatterypackintotheproductasshown.
Makesurethelatchonthebatterypacksnapsintoplace
andthebattery pack issecuredin the productbefore
beginningoperation.
Depress the latch and pull to release and remove the
batterypack.
For complete charging instructions, see the operator’s
manualsforyourbatterypackandcharger.
VARIABLE SPEED SWITCH TRIGGER
See Figure 2, page 10 (HPDD01).
See Figure 2, page 11 (HPID01).
Thevariablespeedswitchtriggerdelivershigherspeedwith
increasedtriggerpressureandlowerspeedwithdecreased
triggerpressure.
ToturnthedrillON,depresstheswitchtrigger.Toturnit
OFF,releasetheswitchtriggerandallowthechucktocome
toacompletestop.
TheLEDlight,locatedonthefootofthetool,willturnon
whentheswitchtriggerisdepressed.
NOTE: Awhistlingorringingnoisecomingfromtheswitch
duringuseisanormalpartoftheswitchfunction.
OPERATION
HPDD01 DRILL/DRIVER
INSTALLING/REMOVING BITS
See Figures 3 - 4, page 10.
Thearrowsonthekeylesschuckindicatewhichdirection
torotatethechucksleevetotightenorreleasethedrillbit.
Donotuseawrenchtotightenorloosenthechuckjaws.
To install bits, locktheswitchtrigger.
Openorclosethechuckjawsuntiltheopeningisslightly
largerthanthebitsizeyouintendtouse.
Raisethefrontofthedrillslightlyandinsertthedrillbit.
WARNING:
Makesuretoinsertthedrillbitstraightintothechuck
jaws.Do notinsert the drillbit intothe chuckjaws at
anangle,thentighten.Thiscouldcausethedrillbitto
be thrown from the drill, resulting in possible serious
personalinjuryordamagetothechuck.
Rotatethechucksleevetocloseandtightenthechuck
jaws.
WARNING:
Donotholdthechucksleevewithonehandandusethe
powerofthedrilltotightenthechuckjawsonthedrill
bit.Thechucksleeve couldslipinyour hand,oryour
handcouldslipandcomeincontactwiththerotating
drillbit.Thiscouldcauseanaccidentresultinginserious
personalinjury.
To remove bits, lock the switch trigger and openthe
chuckjaws.
Thebitprovidedwiththedrillcanbeplacedinthestorage
area,locatedonthebaseofthedrill.
TWO-SPEED GEAR TRAIN
See Figure 5, page 10.
Select lowspeed(1)forapplicationssuchasdrillingin
metal,andforapplicationsrequiringhighertorque,such
asdrivinglargescrews.
Selecthigh speed(2)forfastdrillingordrivingapplications,
suchasdrillinginwoodormasonry.
HPDD01 DRILL/DRIVER / HPID01 IMPACT DRIVER