Datasheet

ManualsBrandsHARTING ManualsConnectorsMultipole socket , H 15-p DIN 41612

5 V

5 mA

Technical characteristics Type H

Current carrying capacity

The current carrying capacity is limited by maximum temperature of

materials for inserts and contacts including terminals. The current

capacity curve is valid for continuous, non interrupted current loaded

contacts of connectors when simultaneous power on all contacts is

given, without exceeding the maximum temperature.

Control and test procedures according to DIN IEC 60 512

Number of contacts 15

14 + 1 leading contact

(position z 32)

13 + 2 leading contacts

(position z 4 und z 32)

Working current 15 A max.

see current carrying capacity chart

Clearance ≥ 4.5 mm*

Creepage ≥ 8.0 mm*

Working voltage

The working voltage also depends

according to the safety

the clearance and creepage

regulations of the equipment

dimensions

of the pcb itself and

Explanations see chapter 00

the associated wiring

Connectors should not be

mated under voltage

Test voltage U

r.m.s.

3.1 kV*

Contact resistance ≤ 8 mΩ

Insulation resistance ≥ 10

Ω

Temperature range – 55 °C … + 125 °C

The higher temperature limit

includes the local ambient and

heating effects of the contacts

under load

Electrical termination

Male connector Connector with faston

6.3 x 2.5 (faston blade

width x wire gauge)

according to DIN 46 245

and DIN 46 247

Solder pins for pcb

connections Ø 1.6 ± 0.1 mm

DIN EN 60 097

Female connector Connector for faston

6.3 x 2.5 (faston blade

width x wire gauge)

according to DIN 46 245

and DIN 46 247

Solder pins for pcb

connections Ø 1.6 ± 0.1 mm

DIN EN 60 097

Cage clamp terminal

0.14-1.5 mm²

Insertion and withdrawal force

≤ 90 N

Materials

Mouldings Thermoplastic resin,

glass-fibre filled, UL 94-V0

Contacts Copper alloy

Contact surface Hard silver plated,

gold plated on request

terminal ends of female

connectors tinned

Mating conditions see chapter 00

Coding systems see page 03.26

Working current

Ambient temperature

* only valid for type H with 15 contacts

Types

power to 15 A

Low currents and voltages

Type H standard contacts have a silver plated surface. This pre-

cious metal has excellent conductive properties. In the course of a

contact’s lifetime, the silver surface generates a black oxide layer

due to its affinity to sulphur. This layer is smooth and very thin and

is partly interrupted when the contacts are mated and unmated,

thus guaranteeing very low contact resistances. In the case of very

low currents or voltages small changes to the transmitted signal

may be encountered. This is illustrated below where an artifically

aged contact representing a twenty year life is compared with a

new contact.

In systems where such a change to the transmitted signal could

lead to faulty functions and also in extremely aggressive environ-

ments, HARTING recommend the use of gold plated contacts.

Below is a table derived from actual experiences.

Recommendation

Gold

Silver

Summary of content (8 pages)

PAGE 1
Technical characteristics Number of contacts Working current 15 14 + 1 leading contact (position z 32) 13 + 2 leading contacts (position z 4 und z 32) 3 15 A max. Type H Current carrying capacity The current carrying capacity is limited by maximum temperature of materials for inserts and contacts including terminals.
PAGE 2
DIN 41 612 · Type H Number of contacts 15 Male connectors Number of contacts Drawing Dimensions in mm Performance level 1 Male connector* for faston 6.3 x 2.5 1 leading contact (position z 32) Part No.
PAGE 3
DIN 41 612 · Type H Number of contacts 15 Female connectors Identification Number of contacts Drawing Dimensions in mm Performance level 1 Female connector for faston 6.3 x 2.5 Types power to 15 A Part No. Cannot be used in a shell housing 15 09 06 215 2811 Contact arrangement View from termination side Contact arrangement View from termination side Performance level 1 Female connector for faston 6.3 x 2.
PAGE 4
DIN 41 612 · Type H Number of contacts 15 Female connectors Number of contacts Part No. Drawing Dimensions in mm Performance level 1 Female connector* with solder pins “low profile“ 2.7 mm 15 09 06 215 28121) 4,7 mm 15 09 06 215 28211) 09 06 215 28922) 5.5 mm 15 09 06 215 28902) 7,7 mm 15 28311) 09 06 215 09 06 215 28912) 10,7 mm 15 09 06 215 28411) Types power to 15 A Identification a 2.7 4,7 5.
PAGE 5
DIN 41 612 · Type H Number of contacts 15 Female connectors Identification Number of contacts Drawing Dimensions in mm Perfomance level 1 Female connector with cage clamp Types power to 15 A Part No. May be used in a shell housing 15 09 06 015 2813 Contact arrangement View from termination side Slot for screw driver Shell housing see chapter 20 Panel cut out Termination instructions 03 . 14 Screw driver width: Stripping length: Wire gauge: 2.5 x 0.4 mm 4 - 7 mm 0.14 - 1.
PAGE 6
Technical characteristics ELECTRONIC SECTION Number of contacts Current carrying capacity 21, 24 2.54 x 5.08 5.08 The current carrying capacity is limited by maximum temperature of materials for inserts and contacts including terminals. The current capacity curve is valid for continuous, non interrupted current loaded contacts of connectors when simultaneous power on all contacts is given, without exceeding the maximum temperature. 6 A max.
PAGE 7
DIN 41 612 · complementary type MH Number of contacts 24 + 7 F + H Male connectors Identification Part No. Number of contacts Performance levels according to DIN 41 612. Explanation chapter 00 3 2 1 09 06 031 2921 Types power to 15 A Male connector for faston 6.3 x 2.
PAGE 8
DIN 41 612 · complementary type MH Number of contacts 24 + 7 F + H Female connectors Identification Number of contacts Part No. Performance levels according to DIN 41 612. Explanation chapter 00 3 2 1 24 + 7 09 06 231 6822 09 06 231 2822 Female connector with wrap posts 1 x 1 mm 24 + 7 09 06 231 6821 09 06 231 2821 Types power to 15 A Female connector with solder pins 4.5 mm Female connector for crimp contacts Order contacts separately, see chapter 02 24 + 7 09 06 231 2881 a b 4.