Service Manual COPYRIGHT © 1999 ANDERS ENGSTRÖM 555ELDOM.EPS ANDERS ENGSTRÖM, ILLUSTRATÖR Östra vägen 46 430 91 HÖNÖ tel/fax 031- 96 84 64 anders@aeillustr.se 990215 May 1999 Victor Hasselblad AB Göteborg Sweden Copyright © 1999 by Victor Hasselblad AB. All rights reserved. No parts of this material may be reproduced, stored in retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopy, recording, or otherwise, without the prior written permission of the Company.
Contents list Camera body 555ELD 1. General 2. Tools 3. Disassembly 4. Reassembly 5. Adjustment, final assembly and calibration of the flash meter 6. Sub-assembly: Front bayonet plate and auxiliary shutter 7. Exploded view: Shell 8. Exploded view: Motor housing 9. Exploded view: Right hand wall & main components 1. 10. Exploded view: Left hand wall & electronics 11. Exploded view: Rear plate & auxiliary shutter 12.
Contents list Camera body 555ELD 24. Exploded view: Motor drive gear box 553ELX/500ELX 25. Exploded view: IR Release unit Revision 0 2.
Related Service Infos 555ELD - 553ELX - 500ELX 01/93 New screw holding the side cover - 553ELX and 500ELX 17/93 Fitted with wrong spacers - 553ELX 20/93 Redesigned flash metering circuit - 553ELX and 500ELX 23/95 New motor - 553ELX 12/96 Tripod foot adapter/kits 01/97 Rechargeable batteries discontinued - 500ELX 06/97 New tripod foot - 553ELX 03/99 Battery compartment - 553ELX 04/99 Release and S-arm redesigned - 553ELX and 500ELX 05/99 Preliminary spare part catalogue - 555ELD 07/99 Ne
1:1 Camera body 555ELD General description Camera type: Medium format single lens reflex camera with a built-in motor, TTL/OTF flash metering and two release systems, one adapted for conventional photography, the other one for digital photography including integrated connections for digital camera backs. Camera body: One-piece, cast aluminium alloy shell with permanently attached motor housing in lightweight magnesium. Tripod socket threads 1/4" and 3/8", and tripod plate for rapid mounting.
1:2 General description Camera body 555ELD Foldable focusing hood with 5x magnification, interchangeable with 90º or 45º prism viewfinders or magnifying hoods. Bright Acute-Matte D* screen interchangeable for other types. Full viewfinder image with all lenses and accessories. Viewfinder and focusing screen: Adaption to digital backs: Integrated databus connections interface directly to leading digital backs. A unique release system with separate front release port on camera activates the digital back.
2 Tools Camera body 555ELD Tool No. Description Used for V-2211 Pin driver Fitting the locating pin in the front plate and the front gear bracket V-2229 Focal length gauge Adjustment of the focal length, mirror 45ºangle and focusing screen V-2236 Microscope Focusing screen adjustment V-4151/52 Focusing tester Focusing screen adjustment V-4705 Focusing screen adapter Focusing screen adjustment V-5423 Riveting jig Replacement of aux.
3:1 Camera body 555ELD Disassembly Motor Housing Remove the lens, film magazine, viewfinder and focusing screen. Unlock the battery cover, operate the release button and disconnect the battery cover at the exact moment when the auxiliary shutter is closed and mirror is in the upper position. Peel back the small palpas cover hiding the screw (821033). Use the short screwdriver V-2245. Remove the inner side cover (22709). 30737, (30742) 30424-1, (30631-1) 823017 Remove the cover (22928).
3:2 Camera body 555ELD Disassembly Remove the tripod foot (30763) by removing the six screws (829790) and the rubber support (30778) held by double-sided tape. When the tripod foot and the rubber support have been removed, four holes are exposed allowing access to the four screws (823745) holding the motor housing (30801) to the main camera body. Insert a screwdriver through the access holes and remove all four screws. The motor housing can now be removed from the main body of the camera. Fig. 3.
3:3 Camera body 555ELD Disassembly To remove the parts from the outer and inner mounting plates proceed as follows (see the exploded views 13 and 14): Remove the small nut (828001), eccentric (22352) and bearing pin (14100). Remove the screw (821033) and washer (810532) and the micro switch (13605) can be separated from the outer mounting plate. Remove the link (22351), clip (817112) and stop arm (13571). Disconnect the spring (814601), remove clip (817115).
3:4 Camera body 555ELD Disassembly Remove the two long screws (823781) located towards the front of the camera shell. Remove the two short screws (823755) located towards the rear of the camera shell. 823335 Remove the cap (22470) from the chassis connector and peel back the leather (22455) covering the two screws (823335). Remove these screws and push the chassis connector into the body of the camera. The shell can now be separated from the body.
3:5 Camera body 555ELD Disassembly Rear plate 815511 105412 820013 Remove the screw (821033) from the centre of the large gear (13557) and lift the gear clear. With the gear removed an additional screw is exposed which must also be removed (820025). Remove the screws (820013 and 820015) securing the rear plate to the left hand wall, the two screws (820015) on the underside and the screws (821017) on the upper side. 821017 13556 22915 820015 13580 Release the camera.
3:6 Camera body 555ELD Disassembly Mirror Disconnect the mirror hinge (30754) from the two pins "A" and release the pin "B" on the mirror frame, from the mirror lever (22460). The complete mirror (30716) can now be separated from the remainder of the assembly. Fig. 13. "B" "A" DIS15.EPS 990316 Fig. 13 Front bayonet plate 820015 Remove the two screws (820015) located at the rear of the bayonet plate. Remove the two screws (823655) that secure the bottom of the bayonet plate to the main camera body.
3:7 Camera body 555ELD Disassembly Right and left hand wall Remove (or cut) the foam plastic pad (22513) to get access to the screws (820014). remove the right hand wall. Fig. 15. 22513 820014 Mechanism plate To dismantle the right and left hand wall proceed using the following sequence: Inner wall right Fig.15 DIS17.EPS Remove the spring (814862). Remove the two screws 990505 (820013) that secure the support (30701). Remove the clip "A" (817115) and lift the plate (22714). Lift the arm (22896).
3:8 Camera body 555ELD Disassembly Outer wall right 13558 810854 Remove the screw (821012) and lift the gear (13558) clear, together with the washer (810854). "D" 820011 821012 Remove the clip "A" (817119) from the inside wall. The release arm (22922) can now be lifted clear of the outside wall. Remove the clip (817112) from the inside wall. The release catch (13570) and the torsion spring (816608) underneath can be lifted clear of the outside wall.
4:1 Camera body 555ELD Reassembly Lubricate the camera as detailed in the appropriate lubrication chart. Use the lubricants listed below: = Isoflex Topas L32 = Mollykote - X = Isoflex PDP-48 = Gleitmo 805-K = Loctite, e.g. Loctite 243 = Safety lacquer Mechanism plate To reassembly the right and left hand walls proceed using the following sequence: DIS19.EPS 990316 Fig. 18 Outer wall right 13558 Lubricate according to Fig. 18.
4:2 Camera body 555ELD Reassembly Outer wall right Lubricate according to Fig. 20. Fit the washer (810703) followed by the B-arm (21221), then fit the washer (810702) followed by the S-arm (22923). Fit the washer (810702) followed by the locking arm (21219) and the two washers (810702/705) and secure them into place with the clip (817123). Fit the auxiliary shutter arm (13554). Fit the gear (22476) and secure it into position with the screw "C" (821031) from the outside wall. Check the function. DIS18.
4:3 Camera body 555ELD Reassembly Release catch/arm adjustment Check and if necessary bend the release catch (13570) at the arrow so that it is engaged by approximately 1mm. Fig. 22. 22922 13570 Fig. 22 REA02.EPS 990316 Refit the gearwheel (13557) temporarily. Rotate the gear anticlockwise and check that the overtravel on the release arm (22922) is approximately 1mm with respect to the release catch (13570). 22922 If adjustment is required, bend the angle on the release arm (22922) see arrow. Fig.
4:4 Camera body 555ELD Reassembly Left hand wall Check the tension of the spring (816864). This should be between 40 and 60 grams. Adjust by bending the spring (816864) as indicated in Fig. 25. REA05.EPS 990505 816864 Fig. 25 Fit the left and right hand walls together and secure with the screws (820014). Fit the foam plastic pad (22513). Fig. 26. 22513 820014 DIS17.EPS 990505 Revision 0 Fig.
4:5 Camera body 555ELD Reassembly Front bayonet plate "A" Before fitting the bayonet plate (30706-1) make sure the camera is released. This is done by turning gear (22476). Note that the pin "A" should be visible from the outside. Fig. 27. 22476 "B" Fitting the front bayonet plate to the camera body: Tension the drive spring by turning the front gear wheel (30413) clockwise 3 turns.
4:6 Camera body 555ELD The key position of the front gear is checked with the camera cocked. This is carried out as follows: Reassembly Position for screw driver 21219 "D" Fit the blade of a screwdriver in the slot on the front gear wheel (30413). Turn the gear in a clockwise direction until the check "C" has passed the locking arm (21219). In this position it is now possible to cock the release arm (22922) against the release catch (13570).
4:7 Camera body 555ELD Reassembly Mirror 30754 Lubricate according to Fig. 31. Make sure the camera is released. Locate the mirror (30716) into position. Connect the mirror hinge (30754) to the two pins "A". "B" Relocate the pin "B" on the mirror frame to the mirror lever (22460). Fig. 31. Test the function of the mirror by fitting the blade of a screwdriver in the slot on the front gear wheel and cock the camera. Release by moving the release catch (13570) to the rear. Fig. 29 "A" DIS15.
4:8 Camera body 555ELD Reassembly Seal between the rear plate and the left side wall using black silicone or similar as shown in Fig. 34 to ensure a tight light seal. Seal here REA09.EPS 990316 Fig. 34 Preliminary adjustment of the focal length 71.40 ± 0.03 mm Mount the front plate "A" in the front of the camera body and place the camera with the rear section in control tool V-2229. Check that the rear section is flat.
4:9 Camera body 555ELD Reassembly Place the ruler with indicator clock onto the gauge and move the indicator around the periphery on the front plate and check that the length is within the tolerance. If the camera body is too short, on the left-hand side, then the front must be moved forward on this side. This is carried out by knocking on the angle on the left wall which provides the support for the bayonet plate. A solid fibre rod and a suitable hammer are used for this operation.
4:10 Camera body 555ELD Reassembly Dog (13525), gear (13567) and gear (13556) "E" "D" Cock the camera as follows: 21219 Fit the blade of a screwdriver in the curved slot on the front gear (30413). Turn the gear in a clockwise direction until the check "C" has passed the locking arm (21219). In this position it is now possible to cock the release arm (22922) against the release catch (13570). Continue the cocking action until the locking arm (21219) operates and stops against the check "D". Fig. 37.
4:11 Camera body 555ELD Reassembly When the gear (13556) is turned in a clockwise direction the dog (13525) should release the setting hook from the check "G". Fig. 39. 1 - 2mm "D" Adjustment: Disengagement should occur when the check "D" has passed the locking arm (21219) and moved a further 1 - 2 mm. (this is a safety margin to ensure that the lens is fully cocked). Fig. 39. If a further movement is needed, then the relationship between the dog (13525) and the gear (13567) must be altered.
4:12 Camera body 555ELD Reassembly Control and Adjustment of Auxiliary Shutter Operate the release catch so that the camera auxiliary shutter opens. Check that the auxiliary shutter blinds do not influence on the light path. Fig. 41. REA12.EPS 990316 Fig. 41 Alignment of the blinds can be adjusted by holding the shaft with a pair of pliers and carefully bend in the desired direction. Check that the shutter pivot point is not loose on the shaft. If this is the case a new shutter must be fitted.
4:13 Camera body 555ELD Reassembly Circuit board and contact flex 820015 CAUTION! When handling the circuit board a grounded bench mat and a wrist strap must be used to prevent ESD damage. Fit the circuit board in position. It is fixed to the wall by insulating double-sided tape (22879), and the two screws (820015). 22918 "A" Put the photo diode in position on the inside of the bottom part of the left hand wall and secure from the outside with two screws (820325).
4:14 Camera body 555ELD Reassembly Camera shell Secure all screws (except those which are secured with loctite) with safety lacquer. Lubricate with Isoflex Topas L32 onto the pin for the teflon button (103773) and put that one in position before inserting the camera body into the camera shell. Insert camera body into the camera shell. This operation requires manipulation to accomplish. Ensure the circuit board and the contact flex are not damaged.
4:15 Camera body 555ELD Reassembly Motor Housing Insert a screwdriver through access holes at the bottom of the housing and secure it to the main camera body with four screws (823745). Fit the rubber support (30778) Fit the tripod foot (30763) and secure it with the six screws (829790). Fig. 48. 30778 823745 30763 Motor Unit 829790 DIS04.EPS Fig.
4:16 Camera body 555ELD Reassembly Lubricate according to Fig. 50. When the wiring has been correctly connected, reassemble the outer mounting plate by using the following sequence: Secure the stop arm (13571), by refitting the bearing pin (14100), the eccentric (22352), the small nut (828001) and secure by the clip (817112). Fit the magnet arm (13561), clutch arm (14099), link (22351), spring (814601) and secure with clip (817115). Fit the micro switch and secure with washer (810532) and screw (821033).
4:17 Camera body 555ELD Reassembly Adjusting the Function of the Micro-Switch The micro-switch (13605) is set so that the current is interrupted when the clutch arm (14099) is 1mm from the top of one of the teeth on clutch gear (13563). 14099 13563 1mm Adjustment: Loosen the screw (821033) which retains the bracket (21312), move the micro-switch upwards if earlier contact breaking is desired and downwards if later contact breaking is desired. Tighten the screw (821033). Fig. 52. REA17.
5:1 Camera body 555ELD Adjustment Checking and Adjusting the Camera Functions Operate the camera. If there is no exposure operation, one reason for this can be that the release lever (30793) is not releasing the cocked action between the release arm (22922) and the release catch (13570). Adjustment: Bend the angle section on the release lever (30793) forwards at the point shown by the arrow "A" in Fig. 55.
5:2 Camera body 555ELD Adjustment Check that the flat side of gear (13558) is parallel with the rear section. Adjustment: The source of current must be removed before adjustment is carried out. If the position of gear (13558) is faulty in relation to rear section, this can be adjusted by modifying engagement with gear (13557). Mark up the tooth engagement between gears (13557 and 13556). Temporarily remove the screw (821033) holding the large gear (13557). Lift the gear up as far as possible for clerance.
5:3 Camera body 555ELD Adjustment RS - Repeated pre-release The same function occurs as in the S position except that the selector knob (30429) remains in the set position and the camera returns automatically to the S position after exposure until the selector knob is returned manually to the 0 position. A - Automatic The camera makes a continious sequensce of exposures as long as the release button remains depressed. The sequential exposure rate in this mode is about 1 frame/sec.
5:4 Camera body 555ELD Adjustment Check that the magnet arm (13561) has free movement between the shanks of spring (816826) during exposure. Adjustment: Bend the front shank of spring (816826) forwards. Check the spring (816826) blocks the magnet arm (13561) when the T-arm (21283) is in the L position. Fig. 60. 816826 13561 Fig. 60 Refit the side cover (30424-1 chrome or 30631-1 black) and the right hand plastic grip (40202) and secure them with the two screws (820019) and one screw (823017).
5:5 Camera body 555ELD Adjustment Checking the databus connections Check the integral control connector to ensure automatic and direct communication between camera body and digital back. Proceed using the following sequence: "A" Short-circuit the two pins "B" and "C". The camera must now release. "B" Pre-release the camera (the micro-switch 852859 is switched on). Connect a digital multimeter to the two pins "C" and "D". Meusure the electric resistance (maximum 5 ohms).
5:6 Camera body 555ELD Adjustment Check the mirror 45o angle using the sighting tube which fits in the holder on the gauge. Tighten the locking screw. Shine a light source towards the oval cut-out in the upper part of the tube so that the white ring of the ocular is illuminated. When the mirror is at 45o the pattern in the sighting tube will appear as shown. Check that the inner white circle is symmetrical and does not lie outside the inner black field.
5:7 Camera body 555ELD Link to: VHABSTS Adjustment Calibration and control of the flash metering system TTL Control/calibration should be carried out each time the camera has been in for repair. The tolerance for the flash meter is ±0.3 EV at all settings. If the Hasselblad Service System 970600 is used, follow the step by step instruction in the STS user manual. Note! For calibration work use ISO 400/LV12. If the Test box 902474 is used follow the instruction below.
5:8 Camera body 555ELD Adjustment Calibration On pressing the MEASURE button one of the three LED´s will light. The variable resistor in the camera (access behind the leather beside the ISO dial) should be turned so that the green LED lights when the MEASURE button is pressed again. If the red LED lights, the resistor is turned anticlockwise and if the yellow LED lights, it is turned clockwise. At least two seconds must be allowed between measurements.
6:1 Camera body 555ELD Front bayonet plate Front plate reassembly Fit the four bayonet tongues (103439) and secure with eight screws (820425). Behind the front plate glue the two foam plastic strips (13212) and (22899) as well as the reflection protector (22527) into place. Place the lens catch (103440) in position and fit the cover plate (105107). Secure with screw (823440). Install the spacer (810409) and the spring (816858). Secure the second screw (823440).
6:2 Camera body 555ELD The hole for the locating pin (812202) is bored with 1.15 mm drill. Use tool V-2211 for driving in the pin. Drive the pin in until the face of the tool touches the front bayonet plate. Fig. 70. Front bayonet plate V-2211 When a new front plate is installed the hole must be drilled using tool 902658 (V-2075), which is equipped with two drill bushes. Remove the swarf and lubricate the bevel gears with grease. Force grease using a syringe into the three small holes.
6:3 Camera body 555ELD Auxiliary shutter Exchanging the auxiliary shutter 825661 840514 Note! For convenience use the aux. shutter jig V-5423 when removing/mounting the pins (811108). Remove the pin (811108), spring retainer, spring (816807) and the upper actuating arm (13580). 810505 816807 Remove the safety lacquer and loosen the locking screws (825661). Remove the two hubs (840514). 811108 The upper shutter flap can now be removed. Ensure that all adjustment washers on the shaft are retained.
7 Camera body 555ELD COPYRIGHT © 1998 ANDERS ENGSTRÖM 55507.EPS ANDERS ENGSTRÖM, ILLUSTRATÖR Östra vägen 46 430 91 HÖNÖ tel/fax 031- 96 84 64 anders@aeillustr.
7 Camera body 555ELD Pos Pcs No. Description Spare Part No.
8 55508.EPS COPYRIGHT © 1998 ANDERS ENGSTRÖM Camera body 555ELD ANDERS ENGSTRÖM, ILLUSTRATÖR Östra vägen 46 430 91 HÖNÖ tel/fax 031- 96 84 64 anders@aeillustr.
8 Camera body 555ELD Pos Pcs No. Spare Part No.
9 55509.EPS Camera body 555ELD COPYRIGHT © 1998 ANDERS ENGSTRÖM 981217 ANDERS ENGSTRÖM, ILLUSTRATÖR Östra vägen 46 430 91 HÖNÖ tel/fax 031- 96 84 64 anders@aeillustr.
9 Camera body 555ELD Pos Pcs No. Description Spare Part No.
9 Camera body 555ELD Pos Pcs No. 54 2 55 1 56 57 58 2 1 1 Spare Part No.
10 COPYRIGHT © 1999 ANDERS ENGSTRÖM Camera body 555ELD ANDERS ENGSTRÖM, ILLUSTRATÖR Östra vägen 46 430 91 HÖNÖ tel/fax 031- 96 84 64 anders@aeillustr.se 55510.EPS 990112 4 7 6 3 8 2 1 5 9 23 11 22 21 10 12 10 13 20 19 14 15 17 18 16 = Soldering should be accomplished in less then 5 seconds. Keep the soldering tip temperature less than 320ºC (608ºF). Avoid applying force to the terminals.
10 Camera body 555ELD Pos Pcs No. Spare Part No. Description 1 2 3 4 5 1 3 1 1 1 22 678 820 014 817 115 22 707 816 864 Foam Screw Clip Inner wall, left Spring 6 7 8 9 10 1 2 1 1 3 22 879 820 015 22 882 12 453 820 011 Double-sided tape Screw PC-board (incl.
11 Camera body 555ELD 55511.EPS COPYRIGHT © 1999 ANDERS ENGSTRÖM 990115 ANDERS ENGSTRÖM, ILLUSTRATÖR Östra vägen 46 430 91 HÖNÖ tel/fax 031- 96 84 64 anders@aeillustr.
11 Camera body 555ELD Pos Pcs No. Spare Part No.
12 Camera body 555ELD 55512.EPS COPYRIGHT © 1999 ANDERS ENGSTRÖM 990119 ANDERS ENGSTRÖM, ILLUSTRATÖR Östra vägen 46 430 91 HÖNÖ tel/fax 031- 96 84 64 anders@aeillustr.
12 Camera body 555ELD Pos Pcs No. Description Spare Part No.
13 Camera body 555ELD COPYRIGHT ' 2001 ANDERS ENGSTR M 55513.EPS ANDERS ENGSTR M, ILLUSTRAT R stra v gen 46 430 91 H N tel/fax 031- 96 84 64 anders.968464@telia.com 010102 2 1 3 12 4 13 5 14 6 15 8 9 16 11 7 10 17 20 21 22 18 19 23 16 29 28 COPYRIGHT ' 2001 ANDERS ENGSTR M ANDERS ENGSTR M, ILLUSTRAT R stra v gen 46 430 91 H N tel/fax 031- 96 84 64 anders.968464@telia.com ELCIRC01.
13 Camera body 555ELD Pos Pcs No. Spare Part No.
14 Camera body 555ELD COPYRIGHT © 1998 ANDERS ENGSTRÖM 55514.EPS ANDERS ENGSTRÖM, ILLUSTRATÖR Östra vägen 46 430 91 HÖNÖ tel/fax 031- 96 84 64 anders@aeillustr.
14 Camera body 555ELD Pos Pcs No. Description Spare Part No.
15 Camera body 553 ELX/500ELX COPYRIGHT © 1998 ANDERS ENGSTRÖM 55315.EPS ANDERS ENGSTRÖM, ILLUSTRATÖR Östra vägen 46 430 91 HÖNÖ tel/fax 031- 96 84 64 anders@aeillustr.
15 Camera body 553 ELX/500ELX Pos Pcs No. Description Spare Part No.
15 Camera body 553 ELX/500ELX Pos Pcs No. 48 49 50 51 52 Revision 1 2 2 2 1 1 Spare Part No.
1655317.EPS COPYRIGHT © 1998 ANDERS ENGSTRÖM Camera body 553ELX ANDERS ENGSTRÖM, ILLUSTRATÖR Östra vägen 46 430 91 HÖNÖ tel/fax 031- 96 84 64 anders@aeillustr.
16 Camera body 553ELX Pos Pcs No. Spare Part No.
17 Camera body 500ELX COPYRIGHT © 1998 ANDERS ENGSTRÖM 50018.EPS ANDERS ENGSTRÖM, ILLUSTRATÖR Östra vägen 46 430 91 HÖNÖ tel/fax 031- 96 84 64 anders@aeillustr.
17 Camera body 500ELX Pos Pcs No. Description Spare Part No. 1 2 3 4 5 1 1 1 1 1 22 118 812 505 13 550 810 864 21 320 Battery cover, compl.
1855319.EPS COPYRIGHT © 1998 ANDERS ENGSTRÖM 981217 ANDERS ENGSTRÖM, ILLUSTRATÖR Östra vägen 46 430 91 HÖNÖ tel/fax 031- 96 84 64 anders@aeillustr.
18 Camera body 553ELX/500ELX Pos Pcs No. Description Spare Part No.
18 Camera body 553ELX/500ELX Pos Pcs No. Spare Part No.
19 Camera body 553ELX/500ELX COPYRIGHT © 1998 ANDERS ENGSTRÖM ANDERS ENGSTRÖM, ILLUSTRATÖR Östra vägen 46 430 91 HÖNÖ tel/fax 031- 96 84 64 anders@aeillustr.se 55320.
19 Camera body 553ELX/500ELX Pos Pcs No. Description Spare Part No.
20 Camera body 553ELX/500ELX 55321.EPS COPYRIGHT © 1999 ANDERS ENGSTRÖM 990115 ANDERS ENGSTRÖM, ILLUSTRATÖR Östra vägen 46 430 91 HÖNÖ tel/fax 031- 96 84 64 anders@aeillustr.
20 Camera body 553ELX/500ELX Pos Pcs No. Spare Part No.
55312.EPS COPYRIGHT © 1999 ANDERS ENGSTRÖM 990119 ANDERS ENGSTRÖM, ILLUSTRATÖR Östra vägen 46 430 91 HÖNÖ tel/fax 031- 96 84 64 anders@aeillustr.
21 Camera body 553ELX/500ELX Pos Pcs No. Description Spare Part No.
22 Camera body 553ELX COPYRIGHT © 1998 ANDERS ENGSTRÖM 55322.EPS ANDERS ENGSTRÖM, ILLUSTRATÖR Östra vägen 46 430 91 HÖNÖ tel/fax 031- 96 84 64 anders@aeillustr.
22 Camera body 553ELX Pos Pcs No. Spare Part No.
23 Camera body 500ELX COPYRIGHT © 1998 ANDERS ENGSTRÖM 50023.EPS ANDERS ENGSTRÖM, ILLUSTRATÖR Östra vägen 46 430 91 HÖNÖ tel/fax 031- 96 84 64 anders@aeillustr.
23 Camera body 500ELX Pos Pcs No. Spare Part No.
24 Camera body 553ELX/500ELX COPYRIGHT © 1998 ANDERS ENGSTRÖM 55324.EPS ANDERS ENGSTRÖM, ILLUSTRATÖR Östra vägen 46 430 91 HÖNÖ tel/fax 031- 96 84 64 anders@aeillustr.
24 Camera body 553ELX/500ELX Pos Pcs No. Description Spare Part No.
25 COPYRIGHT © 1999 ANDERS ENGSTRÖM IR Release unit ANDERS ENGSTRÖM, ILLUSTRATÖR Östra vägen 46 430 91 HÖNÖ tel/fax 031- 96 84 64 anders@aeillustr.se IR_001.
25 IR Release unit Pos Pcs No. Spare Part No.
