User Guide

ManualsBrandsHatco ManualsOtherGRHWSGDM-0902

GLO-RAY

Merchandising Warmer

GRHW-1SGD Series

Installation &

Operating Manual

I&W # 07.05.127.00

This manual contains important safety information

concerning the maintenance, use and operation of

this product. Failure to follow the instructions

contained in this manual may result in serious injury.

If you are unable to understand the contents of

this manual, please bring it to the attention of your

supervisor. Do not operate this equipment unless

you have read and understood the contents of

this manual.

Este manual contiene importante información sobre

seguridad concerniente al mantenimiento, uso

y operación de este producto. Cualquier falla en el

seguimiento de las instrucciones contenidas en este

manual puede resultar en un serio daño. Si usted no

puede entender el contenido de este manual por

favor pregunte a su supervisor. No opere este equipo

al menos que haya leído y comprendido el contenido

de este manual.

Summary of content (12 pages)

PAGE 1
GLO-RAY ® Merchandising Warmer GRHW-1SGD Series Installation & Operating Manual I&W # 07.05.127.00 This manual contains important safety information concerning the maintenance, use and operation of this product. Failure to follow the instructions contained in this manual may result in serious injury. If you are unable to understand the contents of this manual, please bring it to the attention of your supervisor.
PAGE 2
CONTENTS Operation.......................................................................5 Maintenance ..................................................................6 Cleaning ..................................................................6 Light Bulb Replacement .........................................6 Ground Fault Interrupt Circuit................................6 Hatco Limited Warranty..............................................9 Authorized Parts Distributors....................
PAGE 3
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT! Read the following important safety instructions to avoid personal injury or death, and to avoid damage to the equipment or property. WARNINGS WARNINGS To avoid any injury, turn the power switch off at the fuse disconnect switch/circuit breaker or unplug the unit from the power source and allow to cool completely before performing any maintenance or cleaning.
PAGE 4
MODEL DESCRIPTION GRHW-1SGD The Hatco Glo-Ray Merchandising Warmer is ideal for holding hot, wrapped food at customer serving points. This model features a prefocused metal-sheathed heating element above, an electronically controlled heated glass center shelf and an electronic thermostat controlled heated stainless steel base. Units also feature a lighted On/Off switch, sign holder (sign not included), personnel protectors, incandescent display lights and a 6' (183 cm) cord and plug set attached. Figure 1.
PAGE 5
SPECIFICATIONS ELECTRICAL RATING CHART Model GRHW-1SGD Voltage Watts Amps Plug Configuration Shipping Weight 120 1740 14.5 NEMA 5-15P 86 lbs. (39 kg) DIMENSIONS Model GRHW-1SGD Width (A) Depth (B) Height (C) 22-7/8" (58 cm) 20-1/2" (52 cm) 24-1/8" (61 cm) A B C 3 Form No.
PAGE 6
INSTALLATION Sign Holder Screw Personnel Protector Thumb Screws Figure 3. Sign Holder Installation Glo-Ray Merchandising Warmers are shipped with most components pre-assembled. Care should be taken when unpacking shipping carton to avoid damage to unit and components enclosed. 1. Remove the unit from the carton. 2. Remove information packet. To prevent delay in obtaining warranty coverage, fill out and mail in the warranty card. OU T 3. Remove all tape and packing materials. Figure 4.
PAGE 7
OPERATION CAUTION Locate the unit at the proper counter height, in an area that is convenient for use. The location should be level to prevent the unit or its contents from accidentally falling, and strong enough to support the weight of the unit and food displayed. Electronic Temperature Controller for Stainless Steel Bottom Shelf Ground Fault Circuit Interrupt (GFCI) Switch* 199 CAUTION Some exterior surfaces on the unit will get hot. Use caution when touching these areas to avoid injury.
PAGE 8
MAINTENANCE CLEANING 1. To replace a light bulb, disconnect the power supply from the unit and wait until the unit has cooled. Hatco Glo-Ray Merchandising Warmers are designed for maximum durability and performance, with minimum maintenance. 2. Light bulbs have a threaded base. Unscrew the light bulb from the unit and replace it with a new specially coated incandescent light bulb.
PAGE 9
NOTES 7 Form No.
PAGE 10
NOTES Form No.
PAGE 11
HATCO LIMITED WARRANTY THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR PATENT OR OTHER INTELLECTUAL PROPERTY RIGHT INFRINGEMENT.
PAGE 12
HATCO AUTHORIZED PARTS DISTRIBUTORS ALABAMA KENTUCKY NEW YORK (continued) TEXAS Jones McLeod Appl. Svc. Birmingham 205-251-0159 GCS Service Louisville 502-3671788 Appliance Installation Buffalo 716-884-7425 Stove Parts Supply Fort Worth ARIZONA LOUISIANA Auth. Comm. Food Equip. Phoenix 602-234-2443 Chandlers Parts & Service Baton Rouge 225-272-6620 Northern Parts Dist. Plattsburgh 518-563-3200 Armstrong Repair Service Houston 713-666-7100 Byassee Equipment Co.