Manual
59
IND100129-160
All specifications are subject to change without prior notice!
Specications - JH 19T14 MMD-xxx-Axxx (LED version)
SPECIFICATIONS
Note: All specifi cations are subject to change without prior notice!
Please visit www.hatteland-display.com for the latest electronic version.
2/2
Available factory standard cables, 30cm [11.81"] in length.
• VSD100692-1 : 1 x 9P D-SUB (female) - RS-232 (COM1)
• VSD100692-3 : 1 x 9P D-SUB (female) - RS-232 (COM1)
: 1 x 9P D-SUB (female) - RS-232 (COM Touch Screen)
: 3 x BNC (female) (Composite Video in)
• VSD100692-4 : 1 x 9P D-SUB (female) - RS-232 (COM1)
: 3 x BNC (female) (Composite Video in)
Customized cables are possible to support more built-in signals, like: RS-485, RS-422/
RS-485, Buzzer, ON/OFF, Touch (PS/2), 1 x S-Video IN, Remote External User Controls,
Alternative Keypad interface (i2c) and reserved for other signals. Custom cable lengths
can be manufactured.
Sync Signal:
• Digital separate synchronisation
• Composite synchronisation
• Synchronisation on green.
• Auto detects VGA -> WUXGA, interlaced and non interlaced
• Video Signal : Analog RGB 0,7Vp-p
: Input Impedance 75 Ohm
Synchronisation Range:
• Horizontal : 15,0 kHz to 91,1 kHz
• Vertical : 60 Hz* to 85 Hz
* Recommended for optimum picture quality
• 483 (W) x 444 (H) x 82 (D) mm / 19.02" (W) x 17.48" (H) x 3.23" (D)
• Weight: 11.50 kg (approx)
This product have been tested / type approved by the following classification societies:
IEC 60945 4th (EN 60945:2002) ClassNK - Nippon Kaiji Kyokai GL - Germanischer Lloyd DNV - Det Norske Veritas
ABS - American Bureau of Shipping BV - Bureau Veritas CCS - China Classification Society LRS - Lloyd’s Register of Shipping
EU RO MR - Mutual Recognition
• Cables = VSD100692-3, VSD100692-4 or customized cables.
• JH MMDBR STD-A1 = Bracket
• JH 19BRD STD-A1 = Mounting Bracket EN60945 Tested
• JH MMDRO STD-A1 = Rotary Bracket
• JH 19TSV STD-A1 = Sun Visor
• JH 19VED STD-A1 = Vesa Bracket
• JH 19TAP STD-A1 = 21" CRT Adapter frame
• JH 19TAP STD-B1 = 21" CRT Custom Adapter frame
• JH 19TAP STD-A2 = 20" TFT Adapter frame
• JH 19TWC STD-B1 = Water Cover
*Please see user manual for drawings/measurements.
• Operating : Temperature -15 deg. C to +55 deg. C
- Humidity up to 95%
• Storage : Temperature -20 deg. C to +60 deg. C
- Humidity up to 95%
• IP Rating : Protection (EN60529): IP66 front - IP20 rear
• Compass Safe Dist.
: JH19T14MMD-xxx-xxxx - Std: 1.60m Steering: 1.05m
Resolutions:
• VGA : 640 x 480 (including 640 x 350)
• SVGA : 800 x 600 (including 720 x 400)
• XGA : 1024 x 768
• SXGA : 1280 x 1024*
• UXGA : 1600 x 1200
• WUXGA : 1920 x 1200
* Recommended for optimum picture quality. (60 Hz only)
Video Signals (with Multifunction Cable):
• Interlaced NTSC and PAL/SECAM video
• Composite video
Power Supply options:
• 115&230VAC - 50/60Hz + 24 VDC - JH 19T14 MMD-Mxx-Axxx*
• 115&230VAC - 50/60Hz - JH 19T14 MMD-Axx-Axxx
*Multi-Power: You may connect either AC power or DC power or both. In
case both sources are connected, power will be sourced from the AC input.
If AC input is lost, there will be a uninterrupted switch-over to DC input.
Power Consumption:
Operating : 100 W (max)
• DVI-I Signal IN : 1 x 29p DVI Female (or as RGB IN with adapter)
• RGB Signal IN : 1 x 15p HD D-SUB (female)
• RGB Signal OUT : 1 x 15p HD D-SUB (female) - Clone of RGB IN**
• Multifunction : 1 x 160p D-SUB (female) - Also see table below
• USB I/O : 1 x TYPE B Conn. (female) Reserved for future use
• AC Power IN : 1 x Std IEC Inlet
• If AC Power OUT : 1 x Std IEC Outlet (5A Max)
• If DC Power IN : 1 x 2p D-SUB Connector (male) - Amphenol FCC17
**Tested at recommended resolutions. The RGB output signal is at same resolution and sync as the
RGB input. The output is working even if the display unit is turned off, but power cable/supply must
be connected/provided.
On front bezel - Keypad control (IP66) xxx-xxAx models:
• Power On/Off and On Screen Display Menu (push button)
• Brightness Control (up/down - push buttons)
• Hotkeys (left/right - push buttons)
• Mode Status Red/Green/Orange Illuminated LED-Ring Indicator
On front bezel - Potmeter control (IP66) xxx-xxBx models:
• Power On/Off and On Screen Display Menu (push button)
• Brightness Control (rotary control)
• Hotkeys (left/right - push buttons)
• Mode Status Red/Green/Orange Illuminated LED-Ring Indicator
• Speaker / Buzzer
• Resistive* or Capacitive Touch Screen / Optical Bonding Technology*
• Color Calibrated models (ECDIS)
Synchronisation:
Physical Considerations:
T E S T I N G / A P P R O V A L S & C E R T I F I C A T E S
Available Accessories:
Environmental Considerations:
Safety Considerations:
Even although the test conditions for bridge units provide for a maximum
operating temperature of 55°C, continuous operation of all electronic
components should, if possible, take place at ambient temperatures of only
25°C. This is a necessary prerequisite for long life and low service costs.
Supported Signals:
Power Specifications:
Signal Terminals:
User Controls:
Factory Options:
*Note that all 19 inch with resistive touch screens can not be combined with bonding.
Multifunction Cable:
• High Quality TFT with LED Backlight Technology
• 19.0 inch viewable image size, Aspect Ratio 5:4
• TFT active-matrix liquid crystal panel
• MVA (Multi-domain Vertical Alignment) LCD Technology
• Native Resolution : 1280 x 1024
• Pixel Pitch (RGB) : 0.294 (H) x 0.294 (V) mm
• Response Time : 20ms (typical), “black” to “white”
• Contrast Ratio : 1000:1 (typical)
• Light Intensity Standard : 300 cd/m² (typical)
• Viewable Angle : +/- 89 deg. (typical) (Up/Down/Left/Right)
• Active Display Area : 376.32 (H) x 301.056 (V) mm
• Max Colors : 16.7 million
TFT Technology:
TFT Characteristics:
For a full overview, please review our typenumber sheet found on our website:
http://www.hatteland-display.com/pdflink/ind100780-1.php