Manual
60
IND100129-102
All specifications are subject to change without prior notice!
Specications - JH 20T17 MMD-xxx-Axxx (CCFL version)
SPECIFICATIONS
Note: All specifi cations are subject to change without prior notice!
Please visit www.hatteland-display.com for the latest electronic version.
2/2
Available factory standard cables, 30cm [11.81"] in length.
• VSD100692-1 : 1 x 9P D-SUB (female) - RS-232 (COM1)
• VSD100692-3 : 1 x 9P D-SUB (female) - RS-232 (COM1)
: 1 x 9P D-SUB (female) - RS-232 (COM Touch Screen)
: 3 x BNC (female) (Composite Video in)
• VSD100692-4 : 1 x 9P D-SUB (female) - RS-232 (COM1)
: 3 x BNC (female) (Composite Video in)
Customized cables are possible to support more built-in signals, like: RS-485, RS-422/
RS-485, Buzzer, ON/OFF, Touch (PS/2), 1 x S-Video IN, Remote External User Controls,
Alternative Keypad interface (i2c) and reserved for other signals. Custom cable lengths
can be manufactured.
• High Quality TFT with LED Backlight Technology
• 20.1 inch viewable image size
• a-Si TFT (Thin Film Transistor) Active Matrix, RGB Vertical Stripe
Sync Signal:
• Digital separate synchronisation
• Composite synchronisation
• Synchronisation on green.
• Auto detects VGA -> WUXGA, interlaced and non interlaced
• Video Signal : Analog RGB 0,7Vp-p
: Input Impedance 75 Ohm
Synchronisation Range:
• Horizontal : 15,0 kHz to 91,1 kHz
• Vertical : 60 Hz* to 85 Hz
* Recommended for optimal picture quality
• 534 (W) x 481 (H) x 87 (D) mm - 21.02" (W) x 18.93" (H) x 3.42" (D)
• Weight: 13.50 kg (approx)
• Cables = Custom Multifunction Cable to support more signals
• JH MMDBR STD-A1 = Bracket (See user manual)
• JH MMDRO STD-A1 = Rotary Bracket (See user manual)
• JH 20TSV STD-B1 = Sun Visor (See user manual)
• JH 20VED STD-A1 = Vesa Bracket (See user manual)
• JH 20TWC STD-B1 = Water Cover (See user manual)
• Operating : Temperature -15 deg. C to +55 deg. C
- Humidity up to 95%
• Storage : Temperature -20 deg. C to +60 deg. C
- Humidity up to 95%
• IP Rating : Protection (EN60529): IP66 front - IP20 rear
• Compass Safe Dist.
: JH20T17MMD-xxx-xxxx - Std: TBD Steering: TBD
Lifetime Considerations:
Even although the test conditions for bridge units provide for a maximum
operating temperature of 55°C, continuous operation of all electronic
components should, if possible, take place at ambient temperatures of only
25°C. This is a necessary prerequisite for long life and low service costs.
• Pixel Number : 1600 x 1200
• Pixel Pitch (RGB) : 0.255 (H) x 0.255 (V) mm
• Response Time : 30 ms (typical), rise + fall
• Contrast Ratio : 1000:1 (typical)
• Light Intensity : 260 cd/m2 (typical)
• Viewable Angle : +/- 85 deg. (typical) (Up/Down/Left/Right)
• Active Display Area : 408.0 (H) x 306.0 (V) mm
• Max Colors : 16.7 millions
Resolutions:
• VGA : 640 x 480 (including 640 x 350)
• SVGA : 800 x 600 (including 720 x 400)
• XGA : 1024 x 768
• SXGA : 1280 x 1024
• UXGA : 1600 x 1200*
• WUXGA : 1920 x 1200
* Recommended for optimum picture quality. (60 Hz only)
Video Signals (with Multifunction Cable):
• Interlaced NTSC and PAL/SECAM video
• Composite video
• JH 20T17 MMD-AA1-AAAA = Standard AC, Keypad controls only
• JH 20T17 MMD-DA1-AAAC = Standard DC & Capacitive Touch Screen
• JH 20T17 MMD-AA1-AOBA = Standard AC, Bonded, Potmeter Controls, Buzzer
For a full overview, please review our typenumber sheet found on our website:
http://www.hatteland-display.com/pdflink/ind100780-1.php
Power Supply Options:
• 115&230VAC - 50/60Hz - JH 20T17 MMD-Axx-xxxx
• 24 VDC - JH 20T17 MMD-Dxx-xxxx
Power Consumption:
Operating : 100 W (max)
• DVI-I Signal IN : 1 x 29p DVI Female (or as RGB IN with adapter)
• RGB Signal IN : 1 x 15p HD D-SUB (female)
• RGB Signal OUT : 1 x 15p HD D-SUB (female) - Clone of RGB IN**
• Multifunction : 1 x 160p D-SUB (female) - Also see table below
• USB I/O : 1 x TYPE B Conn. (female) Reserved for future use
• AC Power IN : 1 x Std IEC Inlet
• AC Power OUT : 1 x Std IEC Outlet (5A max)
• DC Power IN : 1 x 2p D-SUB Connector (male) - Amphenol FCC17
**Tested at recommended resolutions. The RGB output signal is at same resolution and sync as the
RGB input. The output is working even if the display unit is turned off, but power cable/supply must
be connected/provided.
On front bezel - Keypad control (IP66) xxx-xxAx models:
• Power On/Off and On Screen Display Menu (push button)
• Brightness Control (up/down - push buttons)
• Hotkeys (left/right - push buttons)
• Mode Status Red/Green/Orange Illuminated LED-Ring Indicator
On front bezel - Potmeter control (IP66) xxx-xxBx models:
• Power On/Off and On Screen Display Menu (push button)
• Brightness Control (rotary control)
• Hotkeys (left/right - push buttons)
• Mode Status Red/Green/Orange Illuminated LED-Ring Indicator
• Speaker / Buzzer
• Capacitive Touch Screen / Optical Bonding Technology
• Color Calibrated models (ECDIS)
TFT Technology:
Synchronisation:
Physical Considerations:
T E S T I N G / A P P R O V A L S & C E R T I F I C A T E S
This product have been tested / type approved by the following classification societies: (*=pending)
IEC 60945 4th (EN 60945:2002)* IACS E10* EU RO MR - Mutual Recognition (covers DNV, BV, ABS, GL, NK and LRS certificates)*
Available Accessories:
Environmental Considerations:
TFT Characteristics:
Supported Signals:
Typical Type Numbers:
Power Specifications:
Signal Terminals:
User Controls:
Factory Options:
MMD-xxx-xxBx
MMD-xxx-xxAx
Buzzer-Potmeter-Keypad Keypad
Multifunction Cable:
PRELIMINARY
RY
•
C
RY
L
RELIMINAR
Buzzer
ound on ou
RELIMINAR
L
L