USER MANUAL Series X - Standard Display (STD) Models HD 12T21 STD-xxx-Fxxx - 12.1 inch Standard Display HD 15T21 STD-xxx-Fxxx - 15.0 inch Standard Display HD 17T21 STD-xxx-Fxxx - 17.0 inch Standard Display HD 19T21 STD-xxx-Fxxx - 19.0 inch Standard Display HD 24T21 STD-xxx-Fxxx - 24.0 inch Standard Display HD 26T21 STD-xxx-Fxxx - 25.54 inch Standard Display User Manual STD Series X Updated: 13 Apr 2015 Doc Id: INB100535-1 (Rev 14) Created: 363 Approved: 6542 Please visit www.hatteland-display.
Copyright © 2015 Hatteland Display AS Stokkastrandvegen 87B, N-5578 Nedre Vats, Norway. All rights are reserved by Hatteland Display AS. This information may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any electronic medium or machinereadable form without the prior written consent of Hatteland Display AS. Review also: www.hatteland-display.com/pdf/misc/doc100703-1_permission_to_create_user_manuals.
Contents Contents........................................................................................... 3 Contents of package.....................................................................................................6 General............................................................................................. 7 About this manual.........................................................................................................8 About Hatteland Display............................
Contents Operation........................................................................................ 41 User Controls..............................................................................................................42 On Screen Display (OSD) Menu Introduction.............................................................44 OSD Keycode / OSD Lock Mode................................................................................44 OSD Simplified and Full Menu modes (examples)................
Contents Technical Drawings - Accessories............................................... 75 Technical Drawings - HD CMB SX1-A1......................................................................76 Console Mount Kit 12”,15”,17”,19”.......................................................................... 76 Technical Drawings - HD CMB SX1-A2......................................................................80 Console Mount Kit 12”,15”,17”,19”..............................................................
Contents of package Note: Entries listed below are for Standard factory shipments. Customized factory shipments may deviate from this list. Item Description 1 pcs of Standard DVI Signal Cable. DVI-D 18+1P Male to DVI-D 18+1P Male Single Link - Length 2.0m Illustration HA-SDM-2M 1 pcs of Standard VGA Signal Cable. DSUB 15P Male to DSUB 15P Male - Length 2.0m HA-VGA-2M-32 1 pcs of power cable European Type F “Schuko” to IEC. Length 1.
General 7
Hatteland Display AS About this manual The manual contains electrical, mechanical and input/output signal specifications. All specifications in this manual, due to manufacturing, new revisions and approvals, are subject to change without notice. However, the last update and revision of this manual are shown both on the frontpage and also in the “Revision History” chapter at the end of the manual.
Displays Series X Standard Display (STD) - Introduction Series X Displays and Panel Computers offer the ultimate in performance, convenience, state of the art design and enduring quality for system integrators and boat builders. Series X products offer a range of feature sets optimized for varying requirements and applications.
Touch screen products Introduction to products with touch screen Nearly all of our Series X products with touch screen uses Projected Capacitive Touch screen (PCTS), widely used with great success on mobile phones and typical pad devices. PCTS can be equally effective also for marine applications. One of the advantages of PCTS is that it has features seen in both resistive and surface capacitive touch screen technologies.
Touch screen products Touch Screen Drivers and Documentation All units are shipped with a Documentation and Drivers DVD or CD which contains suitable drivers* for touch screens. (Named MEDIA STD01). You can also visit our website www.hatteland-display.com to view the same list (or even recently new added products) for our models with touch screen. Before using the touch screen, it should be calibrated for your system. Please install the 3rd party software* and use the Calibrate function.
Product Labeling Introduction This section details the locations, content details and specifications for factory mounted labels for all currently available standard Hatteland Display Standard Industrial Display (STD) models. This information will in most cases also apply for most Customized Models as well, but may differ based on customer requirements, in that case, please refer to the customized User Manual (paper or electronic version, dependent on customer requirements).
Product Labeling Label Locations Number ID and coloring based on “Label Size and Types“ table from previous page. All illustrations below is seen from rear (and side where needed) with connectors facing down. Actual labels regarding its size and text orientation vs product size is drawn in. Due to space restrictions on selected units, some labels will be rotated 90 degrees to fit properly.
Product Labeling Warranty label covers screw. Labels placed on rear. HD 24T21 STD-xxx-Fxxx Warranty label covers screw. Labels placed on rear.
Product Labeling Warranty Label If you are to perform service on a unit still under warranty, any warranty will be void if this label show signs of removal attempts (re-gluing) or removed completely. This label is located on the back of the product and covers a key screw. This is to aid service departments to determine if there has been any unauthorized service on a unit still under warranty.
This page left intentionally blank 16
Installation 17
General Installation Recommendations First Things First! ATTENTION! To prevent damage to chassis and glass, please review the illustrations below before handling units. CORRECT HANDLING ! WRONG HANDLING ! IND100148-5 - Rev 03 Humidity Exposure Notice! Applies for non-bonded product only.
General Installation Recommendations 7. If the push buttons of the product are not illuminated, an external, dimmable illumination (IEC 60945 Ed. 4, 4.2.2.3, e.g. Goose neck light) is required for navigational use. The illumination shall be dazzle-free and adjustable to extinction. 8. Information about necessary pull-relievers for cables is indicated in the Physical Connection section of this manual. Attention must be paid to this information so that cable breaks will not occur, e.g. during service work. 9.
General Installation Recommendations D: General rule for console mounted units: To ensure proper cooling airflow, long-life and stable operation for all units, please make sure that the console casing have either fans or decent ventilation holes to prevent overheating inside the console due to the combined temperature of both Display or Panel Computer units together with other electronic instruments.
General Installation Recommendations Ergonomics 1. The front surface of the display glass has an anti-reflective (AR) coating which can be scratched and damaged with improper cleaning. It is recommended to use only 90+% pure Isopropyl alcohol (Isopropanol) and a soft fabric cloth for this first cleaning. Fold a cloth into a small pad, dampen the cloth with alcohol, and wipe the glass from one edge to the other in one direction with one continuous motion. The product glass will require cleaning as needed.
General Installation Recommendations Maximum Cable Length Any cable should generally be kept as short as possible to provide a high quality input/output. The maximum signal cable length will depend on the signal resolution and frequency, but also on the quality of the signal output from the computer/radar.
General Installation Recommendations Housing / Terminal Block Connector Overview Housing / Terminal Block connectors are available in different sizes (example 2-pin, 4-pin, 5-pin) which plugs into the connector area of the unit. They are mounted by factory default and delivered with the unit. The housing / terminal block connectors have steering rails, which ensures that it can not be mounted wrong. The color of these connectors may vary between black, green and orange depending on manufacturer.
General Installation Recommendations Configuring Housing / Terminal Block connectors Below is a brief illustration that might be useful during configuration and installation of such connectors. You will need suitable pre-configured cable(s) and tools to configure the connector(s) and cable(s) that are present in your installation environment. Below is a sample procedure for a 2-pin DC power connector. The procedure is the same for other connectors of this type as listed in table above.
Installation Procedures Panel / Console Mounting Bracket Kit for 12”,15”,17”,19” - Single Key Hole You need: Allen Wrench tool (3mm), 4 pcs of HD CMB SX1-A1 / -A2 or -A3 Kit (-A1 or -A2 included in delivery). Procedure suitable for: Display and Panel Computers with Single Key Hole. Brackets are EN60945 Tested. Attention: A suitable pre-cut panel cutout should be made prior to mounting. Do not force the unit into the panel cutout as it might break the outer glass or scratch the chassis on the unit.
Installation Procedures Panel / Console Mounting Bracket Kit for 12”,15”,17”,19” - Double Key Hole You need: Allen Wrench tool (3mm), 4 pcs of HD CMB SX1-A1 / -A2 or -A3 Kit (-A1 or -A2 included in delivery). Procedure suitable for: Display and Panel Computers with Double Key Hole. Brackets are EN60945 Tested. Attention: A suitable pre-cut panel cutout should be made prior to mounting. Do not force the unit into the panel cutout as it might break the outer glass or scratch the chassis on the unit.
Installation Procedures Panel Cutout / Console Mounting Bracket Kit for 24” You need: Torx T25 tool, 1 pcs of HD CMB SX1-B1 kit (included in delivery). Procedure suitable for: Display and Panel Computers Series X range. Brackets are EN60945 Tested. Attention: A suitable pre-cut panel cutout should be made prior to mounting. Do not force the unit into the panel cutout as it might break the outer glass or scratch the chassis on the unit. Make sure that the panel cutout is not too tight for the unit.
Installation Procedures Panel Cutout / Console Mounting Bracket Kit for 26” You need: Torx T25 tool, 1 pcs of HD CMB SX1-C1 kit (included in delivery). Procedure suitable for: Display and Panel Computers Series X. Brackets are EN60945 Tested. Attention: A suitable pre-cut panel cutout should be made prior to mounting. Do not force the unit into the panel cutout as it might break the outer glass or scratch the chassis on the unit. Make sure that the panel cutout is not too tight for the unit.
Installation Procedures Mounting Bracket for Table / Desktop installation - 24”,26” You need: M5 Unbrako® Hex Key tool and 1 pcs of HD TMB SX1-C1 Mounting Bracket Kit. Fasteners (6 pcs M6) for Table / Desktop location not included. Procedure suitable for: Display and Panel Computers. Attention: A suitable pre-drilled location and knowledge of measurements for both main unit and brackets/tilting functionality should be prepared and checked prior to mounting. Please disconnect ALL cables before proceeding.
Installation Procedures ▼ 6: Depending on installation needs, you may mount the complete unit in ceiling in two different ways. Upside Down Position: User Controls will be upside down, cables go straight up. You may configure Glass Display Control™ (GDC) LED symbols to show or not, since symbols will be seen upside down. Displayed image needs to be flipped vertically. Review http://www.hatteland-display.com/inb100018-4.php (“Glass Display Control™ (GDC) LED & Button operations” section).
Installation Procedures Mounting Bracket, Table / Desktop / Ceiling - 12”,15”,17”,19” Procedure suitable for: Display (MMD/STD) and Panel Computer (MMC) Series X product ranges. Two versions of bracket exists, please review the table below to identify your unit model and bracket type. Brackets that are currently sold/delivered are marked with green color. Those which are obsolete (and replaced by newer type of bracket) are shown in red color.
Installation Procedures HD TMB-SX1-A1 HD 12T21 MMD-xxx-Fxxx HD 12T21 STD-xxx-Fxxx HD 12T21 MMC-xxx-xxxx HD 15T21 MMD-xxx-Fxxx HD 15T21 STD-xxx-Fxxx HD 15T21 MMC-xxx-xxxx “HW01”: Sold since April 2012. Fits Double Key Hole Chassis only. HD TMB-SX1-B1 HD 17T21 MMD-xxx-Fxxx HD 17T21 STD-xxx-Fxxx HD 17T21 MxC-xxx-xxxx HD 19T21 MMD-xxx-Fxxx HD 19T21 STD-xxx-Fxxx HD 19T21 MxC-xxx-xxxx “HW01”: Sold since May 2012. Fits Double Key Hole Chassis only.
Installation Procedures Important to know about LEFT and RIGHT brackets Throughout the following installation procedure for both BRD and TMB brackets, it is important to understand the difference between LEFT and RIGHT brackets. The Display and Panel Computer chassis are not 100% square boxed, but are slightly designed with a minor narrow angled chassis towards the rear (FIG1) to allow easier “dropin” of units into consoles.
Installation Procedures Installation Procedure - BRD Versions Procedure suitable for: Display (MMD/STD) and Panel Computer (MMC) Series X product ranges. You need: - M4, M5 Unbrako® Hex Key tool (not included with delivery). - Fasteners (6 pcs M6) for mounting complete unit onto table or desktop location (not included with delivery). - 1 pcs of HD xxBRD SX1-A1 Mounting Bracket Kit, where xx=15, 17 or 19 inch.
Installation Procedures ▼ 5: Ensure that both Key Hole Plugs slide into the Key Holes and goes to the bottom position (FIG1 and FIG2). If they appear too tight, you may loose the Key Hole Plug screw a few turns and re-try (see previous step 2). FIG3 shows Key Hole Plug correctly into Key Hole and both brackets in place. FIG2 FIG3 FIG1 FIG3 ▼ 6: Tighten Key Hole Screw firmly on each side and make sure the brackets are properly mounted and aligned to the main chassis of unit.
Installation Procedures Installation Procedure - TMB Versions Procedure suitable for: Display (MMD/STD) and Panel Computer (MMC) Series X product ranges. You need: - M4 Unbrako® Hex Key tool (not included with delivery). - Fasteners (6 pcs M6) for mounting complete unit onto table or desktop location (not included with delivery).
Installation Procedures ▼ 5: While unit is lying flat on table, check the Tilting Lock Pin position. These can be pulled out by hand, turned 90° (FIG1) and turned back 90° until the Lock Pin automatically clicks into place by a spring (FIG2). FIG2 Glass Facing Up FIG1 Locked Unlocked ▼ 6: You may now mount the unit onto your desired location.
Physical Connections Connection area of unit (illustration) USB Touch DVI-D In RS-422/RS-485 COM RS-232 COM VGA/RGB In VGA/RGB Out Power Input AC Power Input DC Grounding Screw Note: 19 inch unit used as example above, please review specifications for your actual model. Reduce Cable Tension To reduce tension of the cables you connect, secure them with a cable tie to the available chassis hinges located near the connectors. Note: Amount of chassis hinges can vary depending on model.
Physical Connections Important note for DVI signal detection: Please note that for the operating system to detect DVI signals correctly, the DVI cable MUST be connected physically to the unit during boot up otherwise you may experience a black image. Furthermore certain graphics drivers may need to refresh their device list (often done manually by user - detect devices), while in some cases the Plug-n-Play will automatically detect the DVI signal correctly.
Physical Connections GROUNDING SCREW: Please review “General Installation Chapter”, pt. 7 for more information. Multi-power note: (For units supporting AC & DC input simultaneously) The unit has a dual input power supply which will accept both AC and DC input. If both inputs are connected, the unit will be powered by AC. If AC is disconnected it will automatically switch over to DC without affecting the operation of the unit.
Operation 41
User Controls USER CONTROLS OVERVIEW The units are designed by using Glass Display Control™ (GDC) touch technology to allow interactivity adjusting brilliance (brightness) and control power on / off with the use of illuminated symbols. Note that these symbols are only visible (backlight illuminated) when suitable power is connected.
User Controls Action Indicators: = Built in functionality to determine when the unit requires service in order to perform within preset factory standards. This area will illuminate constantly until the unit is powered off. Note that by touching this symbol no action will be performed or has been assigned. SERVICE Brightness Adjust: Brilliance / Brightness adjustment of the displayed image is adjusted by touching the (-) or (+) illuminated symbols.
OSD Menu Overview On Screen Display (OSD) Menu Introduction The OSD menu consists of main menus and submenus which is very easy to navigate through. All functions are explained in-depth later in this user manual. You should prior to using the OSD menu and functions, be sure to familiarize yourself with how to physically access the menu, how to navigate up/down/left/right, how to modify values, exiting menus and more.
OSD Menu Overview OSD Simplified and Full Menu modes (examples) You may encounter two different menu setups based on factory default or by customized preset configuration. By first apperance they look the same at the main level, but the underlying sub-menus are slightly different. The Simplified Menu mode offers easy and clear access to most commonly used functions. The Full Menu mode offers a more advanced menu with technical information and is suited for more technical minded users.
OSD Menu Overview OSD Menu Structure In this table all functions within menus and their submenus are shown. Functions that begins with an asterix (*) and in bold/red font color style indicates this function/menu is only available during “Full” menu mode. Some functions are not available for all signal sources due to industry standards and signal properties. Functions with a “>” in the end, indicates a submenu or list of options will be displayed. Depth of the sub-menus (levels) are identified from 1 to 5.
OSD Menu Overview Management (page 44) Level 1 (Main Menu) Level 2 Management > < Exit LED Drive > *Communication > Level 3 Level 4 (Slider Bar) < Exit RS232 > 2-wire RS485 > 4-wire RS485/422 > Address RS > (Radio Button) (Radio Button) (Radio Button) (Slider Bar) Level 3 Level 4 Level 5 OSD Misc (page 45,46,47) Level 1 (Main Menu) Level 2 OSD Misc > < Exit OSD Position > Language > Preset Save > < Exit OSD H Position > OSD V Position > < Exit Norsk > English > Français > Deutsch > Italiano
OSD Menu Functions OSD Menu Functions The following section covers all possible settings that the user can (in a certain mode) encounter or needs to adjust via easy understandable menus, text and navigation. For simpler reading the menu choice “Exit” has been left out of description in this chapter intentionally. Whenever “Exit” is available, you can exit current menu and go back to the previous one visited. When there is no more previous menus available, the OSD menu overlay will be shut off and hidden.
OSD Menu Functions Image Settings Lets you configure various visual preferences for any signal. The contents of these submenu are listed below. |---2--- Image Settings - Auto Setup Will automatically fit / reset the current displayed full screen signal and center it based on the active area of the TFT display. This function rely on properties of the incoming signal. ● Note: Only applicable for “VGA” (Analog RGB/VGA) signals. Will override any manual adjustments done previously.
OSD Menu Functions Image Settings - Display - V.Position |--------3-------- Settings as follows: “V.Position” |--------3-------- = Move image within the TFT panel active area Vertically (up/down), values from 0 to 100. ● Note: Default value is centered inside the active TFT panel area. Image Settings - Display - Clock Adjust the horizontal frequency (clock) of the analog signal to improve visibility of the entire image.
OSD Menu Functions Color Mode Lets you adjust the color temperature (Kelvin degrees) of the image. This applies to the Source signal only. OSD Menu overlay will be unaffected. Lower values make the image appear warmer, while higher values will make it appear cooler. The contents of these submenus are listed below.
OSD Menu Functions Management Allows you to adjust voltages for LED (which illuminate the front glass symbols) and setup Serial Communication mode. The contents of these submenus are listed below. |---2--- Management - LED Drive The touch enabled symbols available on the front glass of the unit is backlight illuminated by LED technology. If you have the need to adjust the brightness strength of these LED (to conform with Night Vision situations), you may do so by adjusting this value in real time.
OSD Menu Functions OSD Misc Allows you to customize the visual appearance of the On Screen Display (OSD) menu, such as; position, language, save, load and recall favourite settings and more. The contents of these submenus are listed below. OSD Misc - OSD Position |---2--- Settings as follows: “OSD H.Position” “OSD V.Position” |---2--- = Place the OSD menu overlay Horizontally (left/right), values from 0 to 100.
OSD Menu Functions OSD Misc - Presets - Save *Available in “Full Mode” only |--------3------- Allows to save current state of all function and values to user defined presets. The contents of the submenu is listed below. Settings as follows: “User 1” = Save all OSD settings to User 1 slot. OSD Misc - Presets - Load |--------3------- Allows to save current state of all function and values to user defined presets. The contents of the submenu is listed below.
OSD Menu Functions |---2--- OSD Misc - OSD Lock Mode *Available in “Full Mode” only To prevent accidental or unwanted user intervention, you can set the behaviour of how the OSD menu is accessible by the user. Normally it is by factory default accessible by touching the MENU” symbol on the front glass of the unit. Settings as follows: “Normal Mode” = Default accessible pop-up by touching the “MENU” symbol. For Non-ECDIS Compliant usage. = Ask for key code first (321).
OSD Menu Functions Service Will show various technical and unit related information, such as; Firmware versions, Elapsed Time, Internal Temperature, Fault Status and activation for the internal Test Pattern image useful for troubleshooting. Whenever you are in contact with helpdesk or service personnel, they might require you to read back some of these values in order to precisely pinpoint any problem/question you should have with the unit or its functionality.
OSD Menu Functions |---2--- Service - Test Pattern Will show the internal test pattern with shading color boxes for Red, Green, Blue and Black/White (Grayscale) to check for deviations in the TFT panel/display controller behaviour. It is independent of any current resolution or specifications found in the signal inputs. The test pattern is generated internally in the display controller and is sent 1:1 directly to the TFT panel.
This page left intentionally blank 58
Specifications 59
Specifications - HD 12T21 STD-xxx-Fxxx SPECIFICATIONS Note: All specifications are subject to change without prior notice! Please visit www.hatteland-display.com for the latest electronic version. TFT Technology: Physical Considerations: • High Quality TFT with LED Backlight Technology • 12.1 inch viewable image size, Aspect Ratio 4:3 • TFT active-matrix liquid crystal panel • W:314.00 [12.36''] x H:272.00 [10.71''] x D:64.50 [2.
Specifications - HD 15T21 STD-xxx-Fxxx SPECIFICATIONS Note: All specifications are subject to change without prior notice! Please visit www.hatteland-display.com for the latest electronic version. TFT Technology: Physical Considerations: • High Quality TFT with LED Backlight • 15.0 inch viewable image size, Aspect Ratio 4:3 • TFT active-matrix liquid crystal panel • W:356.00 [14.02''] x H:307.00 [12.09''] x D:71.50 [2.
Specifications - HD 17T21 STD-xxx-Fxxx SPECIFICATIONS Note: All specifications are subject to change without prior notice! Please visit www.hatteland-display.com for the latest electronic version. TFT Technology: Physical Considerations: • High Quality TFT with LED Backlight • 17.0 inch viewable image size, Aspect Ratio 5:4 • TFT active-matrix liquid crystal panel • W:390.00 [15.35''] x H:351.00 [13.82''] x D:73.50 [2.89''] mm [inch] • 4 x M6 VESA mounting 280x150mm, Max 12mm deep • Weight: 5.8kg / 12.
Specifications - HD 19T21 STD-xxx-Fxxx SPECIFICATIONS Note: All specifications are subject to change without prior notice! Please visit www.hatteland-display.com for the latest electronic version. TFT Technology: Physical Considerations: • • • • • W:429.00 [16.89''] x H:382.00 [15.04''] x D:74.50 [2.93''] mm [inch] • 4 x M6 VESA mounting 280x150mm, Max 12mm deep • Weight: 7.8kg / 17.2lbs High Quality TFT with LED Backlight 19.
Specifications - HD 24T21 STD-xxx-Fxxx SPECIFICATIONS Note: All specifications are subject to change without prior notice! Please visit www.hatteland-display.com for the latest electronic version. TFT Technology: Physical Considerations: • • • • • • • • High Quality TFT with LED Backlight 24.
Specifications - HD 26T21 STD-xxx-Fxxx (LED/CCFL version) SPECIFICATIONS Note: All specifications are subject to change without prior notice! Please visit www.hatteland-display.com for the latest electronic version. TFT Technology: Physical Considerations: • • • • • W:621.00 [24.45''] x H:435.00 [17.13''] x D:98.20 [3.86''] mm [inch] • 4 x M6 VESA mounting 280x150mm, Max 12mm deep • Weight: TBD kg (approx) High Quality TFT with LED or CCFL Backlight Technology 25.
This page left intentionally blank 66
Technical Drawings 67
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This page left intentionally blank 74
Technical Drawings - Accessories 75
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
Console Mounting 26” IND100132-274 86 This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. See next page Dimensions might be shown with or without decimals and indicated as mm [inches].
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
This document is the property of Hatteland Display AS. This document and any authorized reproduction thereof, must not be used in any way against the interest of Hatteland Display AS. Any authorized reproduction, in whole or in part, must include this legend. Hatteland Display Proprietary information. Not to be distributed to any third party without written permission. Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm.
Appendixes 97
Pinout Assignments Connectors illustrated here are either standard by factory default or may be available (through factory customization). Note that some combinations may not be possible due to space restrictions. List also valid for customized models. All pin out assignments are seen from users Point of View (POV) while looking straight at the connector. Please review the dedicated datasheet or technical drawings for your actual unit to identify and determine the presence of desired connector.
Pinout Assignments Analog RGB/VGA, 15-pin DSUB High Density Female 5 4 3 2 1 10 9 8 7 6 15 14 13 12 11 PIN 01 PIN 02 PIN 03 PIN 04 PIN 05 PIN 06 PIN 07 PIN 08 PIN 09 PIN 10 PIN 11 PIN 12 PIN 13 PIN 14 PIN 15 RED GREEN BLUE ID2/RES GND RED_RTN GREEN_RTN BLUE_RTN KEY/PWR GND ID0/RES ID1/SDA HSYNC. VSYNC.
Basic Trouble-shooting GENERAL ISSUES FOR TFT PANEL BASED PRODUCTS Note: Applies for a range of various products. This is only meant as a general guide. NO PICTURE / LED BEHAVIOUR: If there is no light at all in the LED at the FRONT, check power cables. If the LED in front is green then check if the brightness is set/adjusted to max brightness. Lack of image is most likely to be caused by incorrect connection, lack of power or wrong BIOS settings.
Declaration of Conformity We, manufacturer, Hatteland Display AS, Stokkastrandvegen 87B, N-5578 Nedre Vats, Norway declare under our sole responsibility that the JH MMD, JH MMC, JH STD, JH MIL, HM NMD, HM MIL, HM CMD, HT STD, HD MMD, HM MMD, HT MMC, HD MMC and HT/HM (computers) product ranges is in conformity with the following standards in accordance with the EMC Directive.
Return Of Goods Information Return of goods: (Applies not to warranty/normal service/repair of products) Hatteland Display referenced as “manufacturer” in this document. Before returning goods, please contact your system supplier before sending anything directly to manufacturer. When you return products after loan, test, evaulation or products subject for credit, you must ensure that all accessories received from our warehouse is returned.
General Terms and Conditions As of January 2015, Hatteland Display AS’ “Terms of Sales and Delivery” and “Warranty Terms” has been substituted by the updated ”General terms and conditions for sale of goods and performance of additional services” (the “General Terms and Conditions”).
Pixel Defect Policy PIXEL DEFECT POLICY Dot-defects (Bright or dark spots on the panel) Due to the effect that dot failures are part of the TFT technology such failure occurrence cannot be prevented basically. Even though dot defects usually occur during production process, new defects can appear within the lifespan of a TFT display. Neither the production at LCD-supplier nor the use of a LCD-Monitor after shipment can be influenced by Hatteland Display.
Notes General Notes: - The unit is type approved according to EN60945 4th, 4.4, equipment category b) protected from the weather. - Other type approvals applies for the different products. Please see the appropriate “Specifications” page in this manual for more information. - Use of brillance and Glass Display Control™ (touch key functions) may inhibit visibility of information at night.
User Notes Appendix IND100077-24 106
Revision History Rev. By Date Notes 00-1 BU SE 23 Feb 2012 Release for internal review. 00-2 ALL SE 16 Mar 2012 Revised after internal review.
w ww.hat tel and-di sp l ay .
