Specification Sheet

2172mm 85-1/2"
95-1/2"
2426mm
TRACED AND INSULATED
SUPPLY MUST BE HEAT
IMPORTANT
3/4" NPT JUNCTION BOX
POWER CONNECTION
MOUNTING LOCATION FOR OPTIONAL INDICATOR LIGHT
41-3/4"
1060mm
FLOOR LINE
7"
178mm
REMOVABLE ABS JACKET
171mm
6-3/4"
927mm
36-1/2"
2299mm
90-1/2"
MOUNTING LOCATION AREA LIGHT FOR OPTIONAL
Ø3/8"
30°
B.C.
Ø8"
Ø203mm
Ø10mm
3X
Ø9"
Ø229mm
TO A BOTTOM SUPPLY UNIT. IN THE OPERATION & MAINTENANCE
MANUAL (PAGE 2) TO CONVERT
OF THE INSTALLATION PROCEDURE TOP SUPPLY SHOWN. SEE STEP 2
1-1/4" IPS SUPPLY UNION (INLET)
1098mm
43 1/4"
6 3/4"
171mm
14"
355mm
20-1/2" 521mm
67-1/4"
1708mm
NOTES:
1. DIMENSIONS MAY VARY BY ± 1/2 INCH [13mm]. 2. TO COMPLY WITH ANSI Z358.1-2009 FOR EMERGENCY EYEWASH OR EYE/FACE WASH AND SHOWER EQUIPMENT: - UNIT SHALL BE INSTALLED IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS AND ACCEPTABLE PLUMBING PRACTICES. - EYEWASH OR EYE/FACE WASH SHALL BE POSITIONED WITH NOZZLES NOT LESS THEN 83.8 CM (33 IN.) AND NO GREATER THAN 114.3 CM (45 IN.) FROM SURFACE ON WHICH USER STANDS AND 15.3 CM (6 IN.) MINIMUM FROM WALL OR NEAREST OBSTRUCTION. - SHOWER SHALL BE POSITIONED SO THAT SHOWER HEAD IS NOT LESS THAN 208.3 CM (82 IN.) NOR MORE THAN 243.8 CM (96 IN.) FROM SURFACE ON WHICH USER STANDS. - SHOWER SPRAY PATTERN SHALL HAVE A MINIMUM DIAMETER OF 50.8 CM (20 IN.) AT 152.4 CM (60 IN.) ABOVE SURFACE ON WHICH USER STANDS, AND CENTER OF SPRAY PATTERN SHALL BE LOCATED AT LEAST 40.6 CM (16 IN.) FROM ANY OBSTRUCTION. 3. DO NOT USE REGULAR PIPE SEALANT. IF NECESSARY USE DOW CORNING 832 SEALANT PLACING 5 SMALL BEADS ON THE MALE THREADS, JUST ABOVE THE FIRST THREAD. (NOTES CONTINUED ON SHEET 2 OF 4.)
3
6"
152mm
DRENCH HOSE
DRENCH HOSE ACTIVATION
VALVE ASSEMBLY
APPROVED: DRAWN:
PART NUMBER DRAWING NO.
SCALE:
SHEET OF
REV
DRAWING TYPE: SIZE: A
BY:ECN NO.
PAGE
DATE:
DATE:
ECN:
REVISED PER
CHK'D.:
Haws Corporation - All Rights Reserved.
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
C
R
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [e-mail]
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
RTM
03/29/05
15201A00
17
0002081781.D
8317CTFP(120V)/ 8317CTFP.220V
1/20
14
FV
10/21/14
FV
1 of 4
INSTALLATION
4921
2014
SP158B FREEZE PROTECTION VALVE (SEE NOTES ON SHEETS 2 & 3 FOR
INSTALLATION INSTRUCTIONS.)
NOTE: PULL ROD AND HANDLE NOT
ASSEMBLED. ORIENTATION OF HANDLE
MUST BE IN UP POSITION WHEN FULLY
CLOSED AND PULL ROD INSERTED IN
HOLE SHOWN.