User's Manual
4
Installation - all models
1. Teach the unique Aqua Logic ID code: The base receiver attached to the Aqua
Logic control unit has a unique ID code that ensures that your unit will not affect
other systems in the neighborhood, and likewise, their remote will not affect
your system. To teach the ID code to the wireless remote unit:
a. On any other wired Aqua Logic display/key-
pad unit, press the "Menu" button (possibly
multiple times) until "Settings Menu" is dis-
played.
b. Press "<" or ">" (again, possibly multiple times)
until "Teach Wireless" is displayed.
c. Press the "+" button to start the teaching pro-
cess.
d. Press and hold any button on the wireless re-
mote display/keypad for 4 seconds. At this
point the LCD on the wireless remote display/
keypad will indicate "Teach Wireless Success-
ful" and the local display/keypad on the Aqua
Logic control unit will also confirm "Teach
Wireless Successful". If this process is not
successful, then refer to the Troubleshooting
section of this manual for additional informa-
tion.
2. Apply labels: The Aqua Logic PS series of controls allow each output (e.g.
AUX1) to be renamed to what is actually being controlled. The wireless remote
display/keypad comes with a sheet of name labels—simply peel the appropriate
label off the sheet and apply to the appropriate set of buttons on the wireless
remote display/keypad.
3. Installation is complete: You can now use the wireless remote display/keypad.
5. Display backlight turns off after a period of time:
AQL2-Wx-RF-PS-x models and AQL2-Tx-RF-PSx models running off wall power:
The display backlight should always illuminate when you press any key on the
unit. If it turns off after a period of time, you can stop this by pressing the menu
key (possibly multiple times) until "Settings Menu" appears. Next press the "<"
or ">" key (possibly multiple times) until "Display Light" appears. At this point,
pressing either "+" or "-" will allow you to select either "Always On" or "On for
60 sec.". After you have selected the desired operation, press the "Menu"
button to lock in your setting. Note that this selection applies to this wireless
remote display/keypad only. Repeat the process of each display/keypad in the
system.
6. Display backlight always on
AQL2-Wx-RF-PS-x models and AQL2-Tx-RF-PSx models running off wall power:
The display backlight should always illuminate when you press any key on the
unit. If it remains on after 60 seconds have elapsed since the last button push,
you can stop this by pressing the menu key (possibly multiple times) until "Set-
tings Menu" appears. Next press the "<" or ">" key (possibly multiple times)
until "Display Light" appears. At this point, pressing either "+" or "-" will allow
you select either "Always On" or "On for 60 sec.". After you have selected the
desired operation, press the "Menu" button to lock in your setting. Note that this
selection applies to this display/keypad only. Repeat the process for each dis-
play/keypad in the system.
7.
The last keypress
was not received
This is usually a temporary problem caused by interference from other equip-
ment that is using the same radio frequency. Try pressing the button again. If
this doesn’t work, go to the Settings Menu/Wireless Channel on any other
Aqua Logic display/keypad and select another channel. Note that after you
change the channel you will have to "re-teach" every wireless remote device in
the system.
8.
The base receiver
is not responding
If this is the first time you are using your remote, or if you have just installed a
new base receiver, run the "Teach Wireless" procedure from any other Aqua
Logic display/keypad. Also, the radio signal may be too weak—try pointing the
remote in the direction of the pool equipment or try moving closer to the pool
equipment. If that doesn’t work, then there may be other equipment that is using
the same frequency. Go to the Settings Menu/Wireless Channel on any other
Aqua Logic display/keypad and select another channel. Note that after you
change the channel you will have to "re-teach" every wireless remote device in
the system.
9.
Teach Wireless needs
to be run
This is caused by the remote not knowing the ID code of the base receiver. Run
the "Teach Wireless" procedure from any other direct wired Aqua Logic dis-
play/keypad.
7
Settings
Menu
Teach Wireless:
+ to start
Teach Wireless:
Successful
Press and hold
wireless button