Pool Vac Ultra ® Installation Manual Plunge into a sparkling clean pool... automatically.
Pool Vac Ultra INSTALLATION MANUAL Congratulations on your purchase of the Pool Vac Ultra automatic pool cleaning system from Hayward. The Pool Vac Ultra is the smart, efficient way to clean your in-ground pool. The Pool Vac Ultra is powered by your pool's filter system and is designed to work well with most systems. Therefore the performance of the Pool Vac Ultra in your pool will be relative to that power source.
Pool Vac Ultra OPTIONAL ACCESSORIES The Hayward Skimmer Vac Plate is a great accessory for achieving a pool cleaning balance that automatically alternates between skimming the pool’s surface and vacuuming with each cycle of the filtration system’s time clock. Benefits include: •Finger-tip dial control for superior skimmer action and proper vacuum settings. •Back-mounted vacuum gauge conveniently located for simple and accurate vacuum measurements. •Adjustable standpipe for various skimmer models.
Installation INSTALLING YOUR POOL VAC ULTRA IS SIMPLE... To prepare your pool for Pool Vac Ultra installation, please follow the easy steps listed below. These instructions are also shown in the “Pool Vac Ultra Installation Video”. After reading these instructions, the “How To” installation video will walk you through the installation step-by-step, and it will also give you some maintenance and troubleshooting hints. These instructions apply to all Pool Vac Ultra models.
Installation INSTALLING YOUR POOL VAC ULTRA IS SIMPLE... Step 4 The hose should reach from the skimmer or dedicated vacuum line to the furthest point in the pool, plus two (2) extra hose sections. (The length of each hose section is four feet.) This extra length is absolutely necessary for proper operation of the Pool Vac Ultra. If the hose is not long enough, it will be necessary to purchase additional hose sections from your Hayward Pool Vac Ultra dealer.
Installation INSTALLING YOUR POOL VAC ULTRA IS SIMPLE... Step 6 Check the water flow reading on the Flow Gauge. (Refer to Step 4, Figure 2). The black disk should be in the box between the “MIN” and “MAX” markings.
Installation INSTALLING YOUR POOL VAC ULTRA IS SIMPLE... Note The V094 Regulator Valve and the Hayward Skimmer Vacuum Plate can only be used to LOWER an initial vacuum reading that is TOO HIGH. The Regulator Valve and the Skimmer Vacuum Plate cannot be used to INCREASE the initial vacuum reading. An initial reading that is too low to meet the water flow setting necessary to operate the cleaner is indicative of a system problem, and not a problem with the cleaner.
Installation INSTALLING YOUR POOL VAC ULTRA IS SIMPLE... Figure 5 Figure 6 Step 9 Observe the Pool Vac Ultra in operation, and make sure that the return line flow is not affecting the Pool Vac Ultra's AquaPilot® programmed steering and preventing the Pool Vac Ultra from cleaning the entire pool. If the Pool Vac Ultra hose is being pushed across the surface of the pool, it will be necessary to redirect the return line water flow downward.
Pool Vac Ultra IMPORTANT TIPS In one piece fiberglass pools there is very little dirt on the walls, but the Pool Vac Ultra will still climb the walls. Due to the shape (severe angles) of most in-ground vinyl liner pools, the Pool Vac Ultra 's cleaning is mostly confined to the bottom (both shallow and deep) and the hopper sides. However, normal dirt and debris do not adhere to these walls. DO NOT COIL HOSE When storing your cleaner the hose sections must be stored straight, not coiled.
Pool Vac Ultra IMPORTANT TIPS Some skimmers have a vari-flow or diverter valve in the bottom of the skimmer. This valve can be turned to regulate skimming and main drain suction. Turn the valve to full skim and then adjust the Flow Gauge vacuum gauge by turning the valve toward main drain suction. Usually this valve is the same size as the Pool Vac Ultra hose end, and it will therefore be necessary to purchase a V098 Hose Adapter (see Figure 7).
Pool Vac Ultra MAINTENANCE TIPS 1. CHECK THE CONDITION OF THE “SHOES, WINGS AND FLAPS” PERIODICALLY. The shoes and wings have wear indicators on their sides and should be checked occasionally to determine if they need replacing. The shoe wear indicator is a line on the side of the shoe that appears as a difference in texture. When this texture difference is no longer visible at the bottom of the shoe when viewed from either side, the shoes must be changed (see Figure 8).
Pool Vac Ultra MAINTENANCE TIPS 3. WING REPLACEMENT a) Using a screwdriver, remove the plugs from both pods (see Figure 9). b) Remove the old wings by bending the wings up toward the sides of the cleaner, and lift them off their hooks (see Figure 10). If any of the wing hooks are broken, take the Pool Vac Ultra to your dealer for pod replacement as the unit will not function properly if the wings are not properly attached.
Pool Vac Ultra MAINTENANCE TIPS 4. FLAP REPLACEMENT: a) Remove the front and rear flaps from your Pool Vac Ultra by inserting a small screwdriver between the flap and the lower body near the pivot point of the flaps (see Figure 11). BOTTOM OF CLEANER Figure 11 b) You will notice that your replacement flaps look similar but are marked “Front” and “Rear” on the flap. Because the springs in the flaps are different, it is absolutely necessary to install the proper flap in the front and rear of the unit.
Pool Vac Ultra MAINTENANCE TIPS 5. POOL VAC ULTRA BUMPER REPLACEMENT: Replacement of the Pool Vac Ultra Bumper is not recommended as a “Do It Yourself” repair, because there is a slight possibility that the replacement might cause a problem in the propulsion system. We strongly suggest that you consult your Hayward Pool Vac Ultra dealer for this repair. A #2 Phillips screwdriver is necessary for this repair. a) Turn off pump. b) Remove Pool Vac Ultra from pool.
Pool Vac Ultra MAINTENANCE TIPS f) Lift “Easy Opening Bottom” (see Figures 14 & 15). g) Remove four (4) “A” screws (see Figure 13). h) Lift the Lower Body Assembly off the Pool Vac Ultra (see Figure 13). i) Remove four (4) “B” screws (see Figure 13). j) Remove bumper carefully, making sure that other cleaner parts are not moved or disturbed. k) Remove two (2) “C” screws (see Figure 13). l) Replace bumper, again making sure that other cleaner parts are not moved or disturbed.
Removal Instructions “EASY OPENING BOTTOM” 6. “EASY OPENING BOTTOM”. The purpose of the “EASY OPENING BOTTOM” is to allow quick access to the turbine/vacuum chamber for easy cleaning and maintenance. Should the Pool Vac Ultra stop moving or become sluggish due to debris trapped in the throat or inside the unit, the turbine/vacuum chamber is accessible following the instructions on pages 12 and 13 of this manual. 1. Turn off pump. 2. Remove Pool Vac Ultra from pool. 3.
Pool Vac Ultra TROUBLESHOOTING GUIDE Problem: Slow/no forward movement CAUSES SOLUTIONS Lack of/improper water flow through cleaner Check water flow with Flow Gauge and adjust as per Step 6, Figure 2. Partial blockage of Pool Vac Ultra throat Clear blockage Worn shoes Replace shoes Worn wings Replace wings Improper cleaner model for application Call 1-800-227-1477 (U.S.A.
Pool Vac Ultra TROUBLESHOOTING GUIDE Problem: Cleaner climbs to water surface and sucks air CAUSES SOLUTIONS Too much/improper water flow through cleaner Check water flow with Flow Gauge and adjust per instructions in Step 6.
Pool Vac Ultra TROUBLESHOOTING GUIDE Problem: Cleaner sticks at steps, corners, etc. CAUSES SOLUTIONS Improper water flow Check water flow with Flow Gauge and adjust as per Step 6, Figure 2.
Pool Vac Ultra DISCLAIMER A) Pool plaster is affected by age, water chemistry, etc. B) Pool plaster can deteriorate over a period of time. C) The integrity of “good” pool plaster is such that a pool vacuum cleaner - automatic or manual cannot remove that plaster. D) The integrity of “good” pool plaster is such that the plaster will cause wear on the Pool Vac Ultra - not vice versa. E) Vinyl is affected by age, sunlight and water chemistry. F) Vinyl can become brittle and weak.
Pool Vac Ultra CONCRETE, DESERT & VINYL MODEL REPLACEMENT PARTS Ref.No. Part No. Description No.
Pool Vac Ultra CONCRETE, DESERT & VINYL MODEL REPLACEMENT PARTS Ref.No. Part No.
Pool Vac Ultra CONCRETE, DESERT & VINYL MODEL REPLACEMENT PARTS 4 3 5 a b 1 c 6 7 8 9 a b c 2 d 10 11 12 13 14 11 15 a 16 b 29 17 Cleaners 18 a 31 b c 19 33 Turbine Kit 20 21 22 a b 32 a 23 b 24 a b A-Frame Kit 30 a) AXV601P b) AXV601D a b 24 25 26 34 a 27 b a b c 28 d 21
HAYWARD POOL PRODUCTS, INC. 2875 Pomona Boulevard, Pomona, CA 91768 Toll Free: 800-227-1477 www.haywardnet.com Copyright © Hayward Pool Products. All rights reserved. manufactured, sold and distributed by Hayward Pool Products, Inc. AquaPilot® is a registered trademark of Hayward Products.
