User Guide

ManualsBrandsHayward ManualsParts & AccessoriesHayward GLX-PCB-RITE Replacement Main PCB Printed Circuit Board for Hayward Goldline AquaRite Salt Chlorination Systems

OPERATION

The Aqua Rite Pro is an automatic chlorine generation system for pool or spa sanitiza-

tion. The operation requires a low concentration of salt (sodium chloride) in the pool

water. These levels are low enough that it normally will not be tasted. The Aqua Rite Pro

automatically sanitizes your pool by converting the salt into free chlorine which kills

bacteria and algae in the pool. Chlorine will revert back to sodium chloride after killing

bacteria. These reactions will continuously recycle virtually eliminating the need to add

sanitizing chemicals to your pool. The only time you may need to add more salt to the

pool is when water is replenished due to backwashing, draining, or splashing (not

evaporation).

The Aqua Rite Pro is designed to handle the purification needs of most residential

swimming pools up to 40,000 gallons (150,000 liters), or the needs of most commercial

pools up to 25,000 gallons (95,000 liters). Check local codes for other restrictions. The

actual amount of chlorination required to properly sanitize a pool varies due to bather

load, rainfall, temperature, and the pool's cleanliness.

Aqua Rite Pro chlorine generators operating with software version 1.10 or later are

designed to use one of 3 different chlorinator cells that are available from your autho-

rized Goldline dealer. These cells are not included with the Aqua Rite Pro and must be

purchased before installation. Choose the appropriate cell based on the size of your

pool. The models are shown below:

T-CELL-15- for pools up to 40,000 gallons

T-CELL-9 - for pools up to 25,000 gallons

T-CELL-3 - for pools up to 15,000 gallons

Note that the installation and mounting requirements are the same for all models.

The Aqua Rite Pro can be used with the optional Goldline AQL-CHEM to provide a fully

integrated chemistry solution for your pool. With the AQL-CHEM installed, the Aqua

Rite Pro senses the pool's ORP and pH levels and automatically generates the correct

amount of chlorine to keep your pool properly sanitized. The Aqua Rite Pro can also

control pH by introducing acid or CO

into the pool using an AQL-CHEM2 (120V), AQL-

CHEM2-240 (240V) or other dispensing device requiring 120VAC or 240VAC on/off

control. The Aqua Rite Pro and AQL-CHEM products offer the user a complete auto-

mated system controlling both sanitization and pH balance.

NOTE: Goldline does not recommend using the Aqua Rite Pro to generate bro-

mine.

NOTE: Before installing this product as part of a saline water purification system in a

pool or spa using natural stone for coping or for immediately adjacent patios/decking, a

qualified stone installation specialist should be consulted regarding the appropriate

type, installation, sealant (if any) and maintenance of stone used around a saline pool

with electronic chlorine generator in your particular location and circumstances.

NOTE: The use of dry acid (sodium bisulfate) to adjust pool pH is discouraged espe-

cially in arid regions where pool water is subject to excessive evaporation and is not

commonly diluted with fresh water. Dry acid can cause a buildup of by-products that

can damage your chlorinator cell.

TROUBLESHOOTING

Check System Indicator

The “CHECK SYSTEM” LED will alert you when the Aqua Rite Pro detects any of the

following conditions that are abnormal and require attention for optimal operation of

your pool. Press “<“ or “>” to view all of the existing “Check System” conditions.

• Inspect Cell -- For optimum operation, you will need to inspect the Aqua Rite Pro

chlorinator cell approximately every 3 months and clean the cell if necessary. The

Aqua Rite Pro will automatically remind you when it is time and display “Inspect Cell,

+ to reset” as part of the rotating Default Menu. Clean the cell (see instructions, page

12) and then press the “+” button during the “Inspect Cell” display to reset the timer.

• Low Salt/Minerals or Very Low Salt/Minerals -- When the salt is too low the Aqua

Rite Pro will generate less chlorine and the life of the cell is degraded. Check the cell

and clean if necessary before adding salt.

240 VAC

120 VAC

EP1

EP2

Ground

For 120VAC operation

position connectors as shown

Ground

to AQL-CHEM2 Pigtail or

120VAC pH Dispensing Device

to AQL-CHEM2-240 Pigtail or

240VAC pH Dispensing Device

WHITE

BLACK

EP1

EP3

240VAC pH Dispensing Device

(Factory Default)

120VAC pH Dispensing Device