Aqua Plus Programming Flow Chart default menu settings menu spa heater1 temperature pool heater1 temperature spa solar temperature pool solar temperature vsp speed settings superchlorinate spa chlorinator setting pool chlorinator setting day and time backlit display light beeper teach wireless remote wireless channel maintenance menu pH calibration wizard clean probe wizard timers menu pool filter 1 or hi-speed 1 pool filter 2 or lo-speed 1 pool filter 3 or hi-speed 2 pool filter 4 or lo-speed 2 spa l
IMPORTANT SAFETY INSTRUCTIONS When using this electrical equipment, basic safety precautions should always be followed, including the following: • READ AND FOLLOW ALL INSTRUCTIONS • ! WARNING: Disconnect all AC power during installation. • ! WARNING: Water in excess of 100 degrees Fahrenheit may be hazardous to your health. • • • ! WARNING: To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times.
Heater Checkout Follow these instructions to verify that the Aqua Plus is properly controlling the heater. 1. Check that the Aqua Plus is calling for the heater to turn on as indicated by the “Heater” LED being illuminated. If the “Heater” LED is illuminated, go directly to step 2; if not, then check the following: • The heater is enabled (Configuration Menu/Heater Config.). • The heater temperature setting is at least 2ºF greater than the water temperature (Settings Menu / Pool Heater & Spa Heater).
Introduction Reset Config. to Default Press + Before You Begin What’s Included Before attempting to install the Aqua Plus system, check that the following components have been included in the package: Aqua Plus Electronics Unit (3) Temperature sensors with 15 ft. (5m) cable, hose clamp Turbo Cell and Flow Switch with 15 ft. cables PVC unions Initiate reset of all configuration parameters Move to previous/next configuration menu (config.
if AQL-SS-6B is connected 6B Spa Config. + to view/change Push to access the 6 Button Spa Side Remote options Move to previous/next configuration menu Select 6B Spa A Rotates between all available remotes Move to next menu item Rotates between System Off, Pool/Spa, Filter, Lights, Heater1, Aux1 and Aux2 Move to previous/next menu item or next configuration menu 6B A, Button 1 Pool/Spa Select 6B Spa This menu only appears if more than one AQL-SS-6B is detected at power up.
The pool’s chemistry must be balanced BEFORE activating the Aqua Plus’s optional chlorinator function. NOTE: If the pool does not have new water, add metal remover and non-copper based algaecide to the pool, per manufacturer’s instructions. This ensures a quick, troublefree transfer to the Aqua Plus system. Valve3 Config.
Countdown Timer – the aux relay will turn on when the AUX button is pressed and then will turn off automatically after a programmed time (see Timers Menu, Operation Manual). The AUX button can also be used to turn the output off. Pool Sizing Formula Liters Gallons Low Speed of a 2-speed Filter Pump – the Aqua Plus will operate the aux relay whenever the low speed operation of the filter pump is required. It is very important that the “2-speed” filter pump option be selected under the “Filter Config.
If “VSP” is selected, the Lights relay is used to supply power to a Hayward Variable Speed Pump (VSP). The relay will be on when the Lights output is on and off when the output is off . On, off and speed are controlled by commands sent to the VSP. 2.
Lights Config. + to view/change Lights Name Pool Light Lights Function Manual On/Off Push to access Lights options Move to previous/next configuration menu Optional Remote Controls Rotates between all available names Move to next menu item or previous/next configuration menu Hayward offers a variety of wired and wireless remote control options for the Aqua Plus. Each model gives you the ability to control your pool’s functions from a remote location, away from the Control Center.
require the user to run the “Teach Wireless” routine in the Settings Menu. This information can be found in the Aqua Plus Operation Manual and the owner’s manual of each remote. AQL2-Tx-RF-P-4 The AQL2-Tx-RF-P-4 is a portable battery operated remote control designed to be used in a weather protected area (rain should never hit the unit). This remote comes with a wall mounted power supply for recharging the builtin batteries.
Freeze Protection Temperature Select the temperature to be used for freeze protection. Temperature is adjustable from 33ºF-42ºF (1ºC-6ºC). 38ºF (3ºC) is default. This threshold will be used for all outputs that have freeze protection enabled. External Input Interlock When enabled, the filter pump will be forced off when the external input is active. Note that freeze protection will have precedence over this feature. 3.
Turbo Cell The Turbo Cell (used for chlorine generation) should be plumbed AFTER the filter and heater. If installed on a pool/ spa combination system, the cell should be plumbed BEFORE the pool/spa return valve in order to allow proper chlorination of both the pool and the spa. Refer to plumbing diagram below: Filter Config.
Pool/Spa Config. + to view/change Pool/Spa Setup Pool and Spa if “Pool and Spa” is selected Spa - CountDn 00:30 Adjust time setting (Manual On/Off, 0:05, 0:10, 0:15..., (default is 4:00)) Move to next menu item if “Pool and Spa” is selected Spa Spillover Enabled Toggle between Enabled and Disabled (default) Spa Spillover Move to next menu item or previous/next configuration menu if “Pool and Spa” is selected and if “Spa Spillover” is enabled Filter Operation Spa Spillover 4.
5. Configuration Menu General Purpose Outlet If desired, a duplex receptacle with weatherproof cover (supplied by installer) may be installed in the knockouts on the lower right side of the Aqua Plus enclosure. Per code, the receptacle should be a GFCI type. Alternatively, connect a standard receptacle to a GFCB. Aqua Plus Control Power The Aqua Plus requires 120VAC, 2A power to operate the control logic circuits and the chlorinator. This power should be connected to one of the circuit breakers.
External Input Interlock The External Input Interlock provides a means to force the filter pump or an Aux output off when certain conditions exists. A normally open or normally closed on/off external device must be connected to the Aqua Plus as shown below. After properly configuring the Aqua Plus (see Configuration), the filter pump and/or desired Aux will be forced off when the device is active. ! WARNING: Do not use the Aqua Plus to control an automatic pool cover.
Base Station Plug in the pigtail connector from the wireless base station into the “wireless” connector on the main PCB in the Aqua Plus control unit. Low Voltage Wiring Valve Actuators The Aqua Plus can control up to three automatic valve actuators. Two of the valve outputs are dedicated to the pool/ spa suction (Valve2) and return (Valve1) valves. Valve3 is for general purpose use (solar, water feature, in-floor cleaner, etc.).
Temperature Sensors The Aqua Plus utilizes 10K ohm thermistor type sensors. Three sensors (water temperature, air temperature and solar temperature) are included. If the Aqua Plus is being used to control a solar heating system, the solar sensor is required. The sensors are provided with a 15 ft. cable. See page 5 and the diagram below for installation information. POOL/SPA SENSOR Laars Heaters 1. 2. 3. 4. 5. AIR SENSOR Turn power off to heater. Remove factory jumper from terminal block.
Pentair/Purex/MiniMax STA-RITE Heater 1. 2. 3. 4. 1. 2. 3. 4. Turn power off to heater. Remove factory installed jumper from the “Ext Switch” connector. Wire the Aqua Plus to the “Ext Switch” connector as shown below. The wires to the Aqua Plus must be separated from any line voltage wires. Failure to follow these instructions may cause erratic operation of the heater. 5. Set the Power (Thermostat Select) switch to either “Pool” or “Spa”. 6.
Pentair/Purex/MiniMax STA-RITE Heater 1. 2. 3. 4. 1. 2. 3. 4. Turn power off to heater. Remove factory installed jumper from the “Ext Switch” connector. Wire the Aqua Plus to the “Ext Switch” connector as shown below. The wires to the Aqua Plus must be separated from any line voltage wires. Failure to follow these instructions may cause erratic operation of the heater. 5. Set the Power (Thermostat Select) switch to either “Pool” or “Spa”. 6.
Temperature Sensors The Aqua Plus utilizes 10K ohm thermistor type sensors. Three sensors (water temperature, air temperature and solar temperature) are included. If the Aqua Plus is being used to control a solar heating system, the solar sensor is required. The sensors are provided with a 15 ft. cable. See page 5 and the diagram below for installation information. POOL/SPA SENSOR Laars Heaters 1. 2. 3. 4. 5. AIR SENSOR Turn power off to heater. Remove factory jumper from terminal block.
Base Station Plug in the pigtail connector from the wireless base station into the “wireless” connector on the main PCB in the Aqua Plus control unit. Low Voltage Wiring Valve Actuators The Aqua Plus can control up to three automatic valve actuators. Two of the valve outputs are dedicated to the pool/ spa suction (Valve2) and return (Valve1) valves. Valve3 is for general purpose use (solar, water feature, in-floor cleaner, etc.).
External Input Interlock The External Input Interlock provides a means to force the filter pump or an Aux output off when certain conditions exists. A normally open or normally closed on/off external device must be connected to the Aqua Plus as shown below. After properly configuring the Aqua Plus (see Configuration), the filter pump and/or desired Aux will be forced off when the device is active. ! WARNING: Do not use the Aqua Plus to control an automatic pool cover.
5. Configuration Menu General Purpose Outlet If desired, a duplex receptacle with weatherproof cover (supplied by installer) may be installed in the knockouts on the lower right side of the Aqua Plus enclosure. Per code, the receptacle should be a GFCI type. Alternatively, connect a standard receptacle to a GFCB. Aqua Plus Control Power The Aqua Plus requires 120VAC, 2A power to operate the control logic circuits and the chlorinator. This power should be connected to one of the circuit breakers.
Pool/Spa Config. + to view/change Pool/Spa Setup Pool and Spa if “Pool and Spa” is selected Spa - CountDn 00:30 Adjust time setting (Manual On/Off, 0:05, 0:10, 0:15..., (default is 4:00)) Move to next menu item if “Pool and Spa” is selected Spa Spillover Enabled Toggle between Enabled and Disabled (default) Spa Spillover Move to next menu item or previous/next configuration menu if “Pool and Spa” is selected and if “Spa Spillover” is enabled Filter Operation Spa Spillover 4.
Turbo Cell The Turbo Cell (used for chlorine generation) should be plumbed AFTER the filter and heater. If installed on a pool/ spa combination system, the cell should be plumbed BEFORE the pool/spa return valve in order to allow proper chlorination of both the pool and the spa. Refer to plumbing diagram below: Filter Config.
Freeze Protection Temperature Select the temperature to be used for freeze protection. Temperature is adjustable from 33ºF-42ºF (1ºC-6ºC). 38ºF (3ºC) is default. This threshold will be used for all outputs that have freeze protection enabled. External Input Interlock When enabled, the filter pump will be forced off when the external input is active. Note that freeze protection will have precedence over this feature. 3.
require the user to run the “Teach Wireless” routine in the Settings Menu. This information can be found in the Aqua Plus Operation Manual and the owner’s manual of each remote. AQL2-Tx-RF-P-4 The AQL2-Tx-RF-P-4 is a portable battery operated remote control designed to be used in a weather protected area (rain should never hit the unit). This remote comes with a wall mounted power supply for recharging the builtin batteries.
Lights Config. + to view/change Lights Name Pool Light Lights Function Manual On/Off Push to access Lights options Move to previous/next configuration menu Optional Remote Controls Rotates between all available names Move to next menu item or previous/next configuration menu Hayward offers a variety of wired and wireless remote control options for the Aqua Plus. Each model gives you the ability to control your pool’s functions from a remote location, away from the Control Center.
If “VSP” is selected, the Lights relay is used to supply power to a Hayward Variable Speed Pump (VSP). The relay will be on when the Lights output is on and off when the output is off . On, off and speed are controlled by commands sent to the VSP. 2.
Countdown Timer – the aux relay will turn on when the AUX button is pressed and then will turn off automatically after a programmed time (see Timers Menu, Operation Manual). The AUX button can also be used to turn the output off. Pool Sizing Formula Liters Gallons Low Speed of a 2-speed Filter Pump – the Aqua Plus will operate the aux relay whenever the low speed operation of the filter pump is required. It is very important that the “2-speed” filter pump option be selected under the “Filter Config.
The pool’s chemistry must be balanced BEFORE activating the Aqua Plus’s optional chlorinator function. NOTE: If the pool does not have new water, add metal remover and non-copper based algaecide to the pool, per manufacturer’s instructions. This ensures a quick, troublefree transfer to the Aqua Plus system. Valve3 Config.
if AQL-SS-6B is connected 6B Spa Config. + to view/change Push to access the 6 Button Spa Side Remote options Move to previous/next configuration menu Select 6B Spa A Rotates between all available remotes Move to next menu item Rotates between System Off, Pool/Spa, Filter, Lights, Heater1, Aux1 and Aux2 Move to previous/next menu item or next configuration menu 6B A, Button 1 Pool/Spa Select 6B Spa This menu only appears if more than one AQL-SS-6B is detected at power up.
Introduction Reset Config. to Default Press + Before You Begin What’s Included Before attempting to install the Aqua Plus system, check that the following components have been included in the package: Aqua Plus Electronics Unit (3) Temperature sensors with 15 ft. (5m) cable, hose clamp Turbo Cell and Flow Switch with 15 ft. cables PVC unions Initiate reset of all configuration parameters Move to previous/next configuration menu (config.
Heater Checkout Follow these instructions to verify that the Aqua Plus is properly controlling the heater. 1. Check that the Aqua Plus is calling for the heater to turn on as indicated by the “Heater” LED being illuminated. If the “Heater” LED is illuminated, go directly to step 2; if not, then check the following: • The heater is enabled (Configuration Menu/Heater Config.). • The heater temperature setting is at least 2ºF greater than the water temperature (Settings Menu / Pool Heater & Spa Heater).
IMPORTANT SAFETY INSTRUCTIONS When using this electrical equipment, basic safety precautions should always be followed, including the following: • READ AND FOLLOW ALL INSTRUCTIONS • ! WARNING: Disconnect all AC power during installation. • ! WARNING: Water in excess of 100 degrees Fahrenheit may be hazardous to your health. • • • ! WARNING: To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times.
Aqua Plus Programming Flow Chart default menu settings menu spa heater1 temperature pool heater1 temperature spa solar temperature pool solar temperature vsp speed settings superchlorinate spa chlorinator setting pool chlorinator setting day and time backlit display light beeper teach wireless remote wireless channel maintenance menu pH calibration wizard clean probe wizard timers menu pool filter 1 or hi-speed 1 pool filter 2 or lo-speed 1 pool filter 3 or hi-speed 2 pool filter 4 or lo-speed 2 spa l
