HAZET-WERK HÖCHSTE TECHNOLOGIE IN DER WERKZEUGFERTIGUNG SEIT 1868 HIGHEST TECHNOLOGY IN TOOL MANUFACTURE SINCE 1868 Betriebsanleitung Pneumatischer Schlagschrauber Operating Instructions 222164 Pneumatic Impact Wrench Geniales Werkzeug 9011 MG 9012 MG 9012 KS 9012 UL 9012-90 9013 MG 9014 MG 9014 MG-LG
HÖCHSTE TECHNOLOGIE IN DER WERKZEUGFERTIGUNG SEIT 1868 EG-Konformitätserklärung Der Hersteller: HAZET-WERK GmbH & Co.
햲 Zu Ihrer Information Sehr geehrter Kunde, Sie haben gut gewählt, denn vor Ihnen liegt ein HAZET-QualitätsProdukt, das Ihren Arbeitsablauf optimieren wird. 1. Allgemeine Informationen • Bitte stellen Sie sicher, dass der Benutzer dieses Werkzeugs die vorliegende Betriebsanleitung vor der ersten Inbetriebnahme gründlich durchgelesen und verstanden hat. • Diese Betriebsanleitung enthält wichtige Hinweise, die zum sicheren und störungsfreien Betrieb Ihres HAZET-Werkzeuges erforderlich sind.
햲 Zu Ihrer Information D 4. Ersatzteile • Nur Original-Ersatzteile des Herstellers verwenden. • Falsche oder fehlerhafte Ersatzteile können zu Beschädigungen, Fehlfunktionen oder Totalausfall des Werkzeuges führen. • Bei Verwendung nicht freigegebener Ersatzteile erlöschen sämtliche Garantie-, Service-, Schadenersatz- und Haftpflichtansprüche gegen den Hersteller oder seine Beauftragten, Händler und Vertreter. 5.
햳 Zu Ihrer Sicherheit Dieser Abschnitt gibt einen Überblick über alle wichtigen Sicherheitsaspekte für einen optimalen Schutz des Personals sowie den sicheren und störungsfreien Betrieb des Gerätes. Zusätzlich beinhalten die einzelnen Kapitel konkrete, mit Symbolen gekennzeichnete Sicherheitshinweise zur Abwendung unmittelbarer Gefahren. Darüber hinaus sind am Gerät befindliche Piktogramme, Schilder und Beschriftungen zu beachten und in ständig lesbarem Zustand zu halten. 1.
햳 Zu Ihrer Sicherheit D 4. Aufbewahrung / Lagerung • • • • • • Das Gerät ist unter folgenden Bedingungen zu lagern und aufzubewahren: Gerät trocken und staubfrei lagern. Gerät keinen Flüssigkeiten und/oder aggressiven Substanzen aussetzen. Gerät nicht im Freien aufbewahren. Gerät für Kinder unzugänglich aufbewahren. Lagertemperatur -10°C bis +40°C. Relative Luftfeuchtigkeit max. 60%. 5.
햳 Zu Ihrer Sicherheit • Gerät nicht in explosionsgefährdeten Räumen verwenden. Werkzeuge wie Schlagschrauber können Funkenschlag verursachen, der zur Entzündung brennbarer Materialien führen kann. Werkzeuge nie in der Nähe von brennbaren Substanzen wie Benzin, Naphtha oder Reinigungsmitteln etc. betätigen. Nur in sauberen, gut gelüfteten Bereichen arbeiten, in denen sich keine brennbaren Materialien befinden.
햴 Aufbau und Funktion D 1. Technische Daten / Geräteelemente Luftanschluß Gewinde Antriebsvierkant Max. Drehmoment Nm 9011 MG 1⁄4˝ 9012 MG 1⁄4˝ 9012 KS 1⁄4˝ 9012 UL 1⁄4˝ 7 250 8 740 8 690 8 461 Empf. Drehmoment Nm 190 542 515 448 Max. Lösemoment Nm 350 1490 1490 493 Schraubengröße Max. Leerlauf-Drehzahl Gewicht Empf.
햴 Aufbau und Funktion 2. Vor Inbetriebnahme Die Benutzung, Inspektion und Wartung von PneumatikWerkzeugen muss immer entsprechend den lokalen staatlichen Landes- oder Bundesbestimmungen erfolgen. • Kompressortank entwässern und Kondenswasser aus den Luftleitungen entfernen. Lesen Sie die Betriebsanleitung für den Kompressor ebenfalls gründlich durch. WICHTIG: Die Verwendung von Luftfiltern und eines Druckluft-Leitungsölers ist zu empfehlen.
D 햴 Aufbau und Funktion 4. Wartung und Pflege Ölen: • Pneumatik-Werkzeuge müssen während ihrer gesamten Lebensdauer geölt werden. Der Motor und die Kugellager benötigen Druckluft, um das Werkzeug anzutreiben. Da die Feuchtigkeit in der Druckluft den Motor rosten lässt, muss der Motor täglich geölt werden. Hierfür ist die Verwendung eines integrierten Ölers zu empfehlen. • HAZET 9070-1 Öler zur Montage am Pneumatik-Werkzeug.
USA 햲 For Your Information Dear Customer, You have made a good choice. This HAZET tool in front of you is a high-quality product that will make your work easier. 1. General Information • Please make sure that the user of this tool carefully reads these operating instructions and fully understands all information given before it is used. • These operating instructions contain important advice that is necessary for a safe and trouble-free operation of your HAZET tool.
햲 For Your Information USA GB 4. Spare Parts • Only use the manufacturer’s original spare parts. • Unsuitable or defective spare parts may cause damage, malfunction or total failure of the tool. • The use of non-approved spare parts will void all warranty, service and liability claims as well as all claims for compensation against the manufacturer or its agents, distributors and sales representatives. 5.
햳 For Your Safety USA This paragraph gives an overview of important security advice to help to ensure the optimal protection of the personnel as well as the safe and trouble-free operation of the tool. Additionally, the different chapters contain security advice that is marked with symbols in order to avert immediate danger. Furthermore, all stickers and labels on the tool must be observed and must be kept legible. 1.
햳 For Your Safety USA 4. Storage The tool has be stored according to the following conditions: • Keep tool in a dry and dust-free place. • Do not expose the tool to liquids or aggressive substances. • Do not store the tool outdoors. • Keep the tool out of reach of children. • Storage temperature: -10°C up to +40°C • Relative air humidity: max. 60% 5. Dangers emanating from the tool Before each use, check the HAZET Air Tool for full functional efficiency.
USA 햳 For Your Safety • Do not point the tool at any person. Keep children and other persons out of the work area when operating the tool. • Do not use the tool in no-load operation. • Pneumatic tools must not get in contact with sources of electricity. • Pay attention to the working pressure, (max. air pressure see table, page 16). Exceeding the approved maximum pressure of tools and accessories can cause explosions and may result in severe injuries.
햴 Design and Function USA GB 1. Technical Data / Components of the Tool Air inlet thread Square drive Max. torque Nm 9011 MG 1⁄4˝ 9012 MG 1⁄4˝ 9012 KS 1⁄4˝ 9012 UL 1⁄4˝ 7 250 8 740 8 690 8 461 Recommended torque Nm 190 542 515 448 Max. loosening torque Nm 350 1490 1490 493 Screw size Max.
햴 Design and Function USA GB 2. Prior to Operation 3. Operation Pneumatic tools have to be used, inspected and maintained always in compliance with the respective local, state, national or federal regulations. • Drain compressor tank and remove condensation water from the air hoses. Read thouroughly the operating instructions of the compressor tank, too. • Turn on the compressor to start the filling of the air tank. • Adjust the air compressor regulator to 90 PSI (6.3 bar).
USA 햴 Design and Function 4. Maintenance and Cleaning Oiling: • Pneumatic tools have to be oiled throughout their whole service life. The motor and the (ball) bearings need compressed air to power the tool. As the moisture in the compressed air leads to rust of the motor, daily oiling of the motor is necessary. For this, the use of an integrated oiler is recommended. • HAZET 9070-1 Oiler can be fixed directly to the pneumatic tool.
Notizen / Notes 19
222164 IV 03.2011/앝 be/BASSO HAZET-WERK Hermann Zerver GmbH & Co. KG • } 10 04 61 • D-42804 Remscheid • Germany [ +49 (0) 21 91 / 7 92-0 • \ +49 (0) 21 91 / 7 92-375 • ^ hazet.de • ] info@hazet.