INSTALLATION MANUAL
IMPORTANT SAFETY INSTRUCTIONS When using an electrical furnishing, basic precautions should always be followed ,including the following: WARNING: To reduce the risk of burns,fire,electric shock or injury to persons. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer. Never drop or insert any object into any opening.Do not use outdoors. WARNING: Risk of electric shock.
HARDWARE AND TOOLS ( Tools not included) Power Drill Mallet Tape Measure Safety Goggles 1/4”& 1/8” Drill Bits Pencil Level HARDWARE LISTS ITEM IMAGE NAME 1 Mounting Screw 2 Wall Anchor 3 Top Bracket 4 Bottom Bracket 5 Glass Shelf 6 Side Mirror 7 Side Mirror Screw 2
INSTALLATIONINSTRUCTIONS APPLY TO BELOW STYLE OF LED MEDICINE CABINET Please read carefully and save these instructions Don't discard any of the packaging until you are sure that you have all of the parts and the fitings Make sure power to the junction box is off before commencing installation. IMPORTANT 1. Unpack LED cabinet. DO NOT lay cabinet on tiled or concrete surface prior to installation Cabinet must be on protected surface to prevent chipping of the corners 2.
SURFACE MOUNT INSTRUCTION Step 1 Step 2 Measure and mark the bottom mounting holes on the wall corresponding to the pre-drilled the locations in the bottom mounting bar. Unpack the LED medicine mirror and prepare tools needed. Draw horizontal line connecting the bottom marked location. The line should be level. Adjust to level if necessary. Step 4 Step 3 Drill holes,and put in the plastic expansion bolt. Attach the bottom mounting bar hanger to the wall with mountin screws from the hardware pack.
Step 5 Put the cabinet on the bottom bar hanger and hold the cabinet, please make sure that the hanger must mach the track from the bottom board of the cabinet. Bottom bracket Connect hardwire to power line. Make sure the power off(Voltage:AC110-12V,50/60Hz) Step 6 Install the top bracket with the same way as the bottom bar.
Step 7 1: Remove the mirror doors; 2: Install the side mirror planel on both sides of the cabinet; 3: Insert the glass shelf into the shelf clamp and adjust to suitable position.
sider for adjustable shelyes, unscrew and adjust the position of shelf directly and then tighten the screw for mixed.
24 in.(W) x 36 in.(H) x 5 in.(D) 23-1/4 in.(W) x 35-5/16 in.(H) x 3-7/8 in.(D) 48 in.(W) x 36 in.(H) x 5 in.(D) 47-1/4 in.(W) x 35-5/16 in.(H) x 3-7/8 in.(D) 60 in.(W) x 36 in.(H) x 5 in.(D) 59-1/4 in.(W) x 35-5/16 in.(H) x 3-7/8 in.
Step 2 Connect hardwire to power line. Make sure the power off (Voltage:AC110-12V,50/60Hz) Step 3 Step 4: As for the shelf and cabinet door installation and adjusment, please refer to page 6 & 7.
INTRODUCTION OF TOUCH FUNCTION 1. Click the power button to turn the light ON/OFF. Click again to choose the light(natural light/warm yellow/white light). 2. Long press the button to make the light gradually dims Long press the button again and the light gradually brightens. Click this button turn the defogger ON/OFF. Time & Room Temperuture Display: Time and room temperuture auto switch every 8-10 seconds. Clock Setting: Long press the defogger button first.
B A C A - Width B - Height C - Depth Unit: Inch SKU# RAIL2436L A 24 B 36 C 5 RAIL2436R 24 36 5 RAIL4836D 48 36 5 RAIL6036T 60 36 5 Note: All dimensions & specifications are approximate and subject to change without notice. Customer Service: For any questions or queries regarding our products, please contact our support team: Email :cs@hbezon.com Website:www.hbezon.