Installation Manual

Replacement Part Kit: #6985 871-330 Instruction 1-800-977-7293 www.hdhudson.com/FAQs ©2017 Manufactured by H. D. Hudson Manufacturing Company
FOR YOUR SAFETY
This sprayer operates with liquid under pressure. Failure
to observe cautions and follow instructions for use and
maintenance can cause tank, hose or other parts to
become corroded, weakened, and/or burst. This can result
in serious injury or property damage from forcible ejection
of parts or high-pressure discharge of spray material. Do
not use any flammables or boiling liquids in this sprayer
as it is not designed nor intended for such use. Some
spray materials can ignite or explode. Do not spray in an
enclosed space, near an open flame such as found in a bbq
grill or water heater, near an electric motor or open switch,
or any source of heat. Do not smoke while spraying. Use
of flammables could result in serious injury or property
damage from unintended ignition or explosion. Do not
use any caustics or acids in this sprayer, since these can
damage or weaken the sprayer and its parts, resulting
in serious injury or property damage. Keep out of reach
from children and pets. Always read and follow directions
on the spray material container, including the need for
protective clothing. Before using your sprayer, thoroughly
inspect both inside and outside of the sprayer and do not
pressurize sprayer if tank, hose or other parts appear to be
damaged, discolored, brittle, excessively soft or loose. Do
not pressurize with any mechanical device such as an air
compressor, since this can create dangerous pressure and
bursting of parts and result in serious injury. Wear long-
sleeved shirt, pants, gloves, goggles or similar protective
clothing when spraying. PROP 65 WARNING: This product
contains one or more chemicals, including lead, known to
the State of California to cause cancer and birth defects or
other reproductive harm. Wash hands after handling.
LIMITED WARRANTY
H. D. Hudson Manufacturing Company warrants to the
original consumer purchaser of this product at retail that
it is free from problems in materials and workmanship for
the period of 3 years from the original date of purchase.
This warranty does not apply to damage to the product
resulting from accident, misuse, neglect, alteration,
modification, tampering, or failure to follow instructions
supplied with the product. This warranty does not cover
normal wear and tear of o-rings or seals, and the warranty
shall be void if the product is used commercially. If the
product or any part of it should malfunction within the
warranty period, call 1-800-977-7293. Valid only in North
America.You must retain your sales receipt as proof of the
date of purchase and include it with any return of
the product.
H. D. HUDSON MANUFACTURING COMPANY EXCLUDES
LIABLITY UNDER THIS WARRANTY FOR ANY AND ALL
INCIDENTAL AND CONSEQUENTIAL LOSS OR DAMAGES.
92130 Commercial™ Wheeled Spray Wagon
Polyethylene Sprayer Instructions
If you have any questions or concerns, or missing parts, do not return sprayer to the store.
Call our hotline: 1-800-9-SPRAYER (1-800-977-7293)
View Online
See maintenance and assembly videos on the internet:
www.hdhudson.com/instructional-videos
HOW TO ASSEMBLE
Slip handle over wings on top of tank. Push down,
position and snap sides of handle onto place.
Insert pins into handle.
Slide large hose cap nut onto hose, threads face end
of hose. Insert hose barb to end of hose. Insert supply
tube into hose barb. (Do not use small cap nut, save for
step F).
A.
B.
C.
A. B. C.
Insert the supply tube into the tank and securely thread
on the large cap nut.
Make sure the large cap nut is threaded all the way
down. If loose, it may come off with force or spray may
escape, resulting in injury.
D.
E.
D. E.
Slide small cap nut onto open end of hose, threads face
end of hose. Insert open end of hose onto shut-off valve
barb. Be sure hose is all the way over the shut-off valve
barb. Tighten small cap nut to shut-off valve.
F.
F.
Please see back page to identify all parts
included in box that are needed for assembly.
HOW TO FILL
A. B.
C.
Unlock pump handle by pushing down and turning handle.
Do not unscrew pump cap or remove pump. Using the
handle, pump up and down. The more you pump, the more
pressure you will build up inside the tank. When it becomes
difficult to pump, your tank has reached maximum pressure.
Do not stand so your head is over pump.
• Use low pressure (fewer strokes) for a coarse spray.
• Use high pressure (more strokes) for a ne mist or a
long-reaching stream.
HOW TO PRESSURIZE
Insert spray wand through wand cap nut and insert
wand into shut-off valve. Screw down wand cap nut
onto shut-off valve. Screw wand cap nut onto the
shut-off valve.
Note: This is not a compression fitting, but it is normal
for nut to screw on tightly.
G.
Pour measured amount of spray material into the open
tank. Follow label directions on spray material container
for amount to use.
Add water as directed. Do not fill beyond the max fill line.
Insert pump and turn clockwise to seal.
Do not over tighten.
A.
B.
C.
G.
HOW TO SPRAY
Turn sprayer on its side and turn nozzle away from you.
Squeeze lever or push button to “ON” and let all the air
escape. Turn sprayer up-right and slowly unscrew pump
from tank and remove it. Do not stand so your head
is over pump.
Shower head nozzle
Clean and dry your sprayer after every use to greatly prolong
its useful service life. Many spray materials will harden if
left in the sprayer and plug up the nozzle, shut-off valve
or supply tube. The soft parts, O-rings and gaskets, will
ultimately wear out and need replacing, just like the oil filter
on your car, for example. How often they need replacing
depends on how much you spray, the spray materials you
use and whether or not the sprayer is regularly cleaned
after use. Call 1-800-9-SPRAYER to obtain genuine Hudson®
replacement parts. If you leave your sprayer in the garage
over Winter, particularly in northern areas, the soft parts may
dry out and need servicing before you use your sprayer for
the first time in the Spring.
SERVICE AND MAINTENANCE
HOW TO RELEASE PRESSURE
Pic-A-Pattern
™
- dual nozzle
system with a choice of fan
or cone nozzle patterns.
Release handle to stop.
Push handle back to unlock.
Squeeze handle to spray.
Push handle forward to lock.