Preguntas, problemas, o piezas faltantes? Antes de regresar a la tienda, llama al Servicio al Cliente de HDX de lunes a viernes entre 8 a.m. y 6 p.m., (hora del Eete de EE. UU.) 1-800-514-6729 HOMEDEPOT.COM Guarde este manual para futuras consultas Model # HDXST9040 USE AND CARE GUIDE 18 GA. 1-5/8” STAPLER (Model#HDXST9040) Question, Problems,missing parts? Before returning to the store, call HDX Customer Service 8 a.m - 6 p.m, EST, Monday- Friday 1-800-514-6729 HOMEDEPOT.
Table of Contents Table of Contents-------------------------------------------------2 Safety Information------------------------------------------------3 Symbols----------------------------------------------------------3 Work Area--------------------------------------------------------3 Personal Safety--------------------------------------------------3 Safety Information(Continued)----------------------------------4 Personal Safety(Continued)-------------------------------------4 Tool Use and Care----------
Safety Information(Continued) PERSONAL SAFETY(CONTINUED) 12.Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. 13.Do not attach the hose or tool to your body. Attach the hose to the structure to reduce the risk of loss of balance if the hose shifts. 14.Always assume that the tool contains fasteners. Do not point the tool toward yourself or anyone whether it contains fasteners or not. 15.
HDX PNEUMATIC NAILER LIMITED ONE-YEAR WARRANTY Warranty LOADING TOOL Safety Information(Continued) AIR SUPPLY AND CONNECTIONS This warranty covers defects in workmanship or materials in this HDX pneumatic nailer for the one-year period from the date of purchase. This warranty is specific to this pneumatic nailer. Warranties for other HDX products may vary. This warranty applies only to the original retail purchaser and may not be transferred.
Specifications Air consumption: 5.87 SCFM with 100 fasteners per minute @ 90 psi Air inlet: 1/4 inch NPT Magazine capacity: 100 fasteners, 18 gauge Weight: 2.75 lbs Maximum pressure: 100 psi Pressure range: 60 psi – 110 psi Pin size range: 1/2 inch to 1-5/8 inch Features 38mm 32mm 25mm 19mm 16mm 13mm 1-5/8" 1-1/2" 1-1/4" 1" 3/4" 5/8" 1/2" 1/4" 5.7mm 40mm (1 . 25mm) 0 . 050 " Compatible With All Generic 18 Gauge 1/4" Crown Staples. 0 . 041 " (1.
Non-marring pad WARNING: Disconnect the tool from the air source whenever clearing a jam. After disconnecting the tool from the air compressor, there, should still be enough air pressure to fire the tool. After the air hose is disconnected, always fire the tool into scrap wood repeatedly to make sure all of the compressed air is expended. WARNING: Make sure there is no fastener in magazine before clearing a jam.
Maintenance WARNING: Any time inspection, maintenance, and cleaning are done: Disconnect the tool from the air source. Empty the magazine completely. ANTI-DUST CAP Each tool is packed with an anti-dust cap on the air connector, check it after unpacking. Keep the anti-dust cap covering the air connector when the tool is not in use. LUBRICATION Frequent, but not excessive, lubrication is required for best performance.
Troubleshooting WARNING: Stop using tool immediately if any of the following problems occur. Serious personal injury could result. Any repairs or replacements must be done by a qualified service person or an authorized service center. Corrective action Tighten screws Replace O-rings Replace bumper Possible cause(s) Loose screws in housing Damaged O-rings Damaged to bumper Tighten screws Replace gasket Problems Air leaking between housing and nose.
Modelo # HDXST9040 GUÍA DE USO Y MANTENIMIENTO GU ENGRAPADORA CALIBRE 18 DE 40MM(1-5/8’’) (Modelo#HDXST9040) Preguntas, problemas, o piezas faltantes? Antes de regresar a la tienda, llama al Servicio al Cliente de HDX de lunes a viernes entre 8 a.m. y 6 p.m., (hora del Eete de EE. UU.) 1-800-514-6729 HOMEDEPOT.
Informacón de Seguridad ADVERTENCIA: Para evitar lesiones personales graves, no intentes usar este producto hasta haber leído y comprendido el manual por completo. Guarda este manual y consúltalo con frecuencia para un funcionamiento seguro y para instruir a otros usuarios de esta herramienta. ADVERTENCIA: Cuando se usen herramientas, siempre se deberán seguir precauciones básicas, incluyendo las siguientes.
19.Nunca coloque las manos ni otra parte del cuerpo en el área de descarga de sujetadores de la herramienta. La herramienta podría lanzar un sujetador y provocar lesiones personales graves o la muerte. 20.Nunca transporte la herramienta de la manguera de aire comprimido ni jale la manguera para mover la herramienta o un compresor. Mantenga las mangueras alejadas del calor, el aceite y los bordes filosos.
ADVERTENCIA: Las advertencias y precauciones mencionadas anteriormente no abarcan todas las condiciones y situaciones posibles. Es perfectamente comprensible que no podemos fabricar el sentido común y la precaución como partes de ningún producto, el usuario es el responsable de obrar en consecuencia. Informacón de Seguridad(Continuación) CARGAR LA HERRAMIENTA 1. No cargues la herramienta con fijadores si alguno de los controles operativos está activado. 2.
Características Escape ajustable en 360 grados Permite al usuario controlar el aire lejos de los cara. Cómoda manija de agarre Para mayor comodidad y control. Estructura de diseño ergonómico Resistente y cómoda, que resulta en una herramienta liviana ideal para un uso prolongado. Contacto de seguridad que no se raya Elimina el daño en las superficies de trabajo.
Cómo configurar la presión de aire ADVERTENCIA: Desconecte la herramienta del suministro de aire antes de retirar o reemplazar la almohadilla que no raya. El incumplimiento de dicho paso podría provocar graves lesiones personales. Operación(Continuación) 6 Ajuste de profundidad La cantidad de presión de aire requerida depende del tamaño de los fijadores y del material de la pieza de trabajo.
Mantenimiento ADVERTENCIA: Antes de inspeccionar, mantenimiento y limpiar: Desconecta la herramienta de la fuente de aire. Vacía el cargador por completo. FUNCIÓN ANTIPOLVO dar Todas las herramientas vienen con un tapón antipolvo en el conector de aire; verifícalo si lo tienes después de desempacar la herramienta. Mantén el tapón antipolvo para cubrir el conector de aire. LUBRICACIÓN La herramienta está diseñada exclusivamente para no necesitar lubricación diaria.
Solución de problemas La herramienta omite colocar sujetadores. Fuga de aire entre el armazón y la cubierta. Fuga de aire entre el armazón y el borde. Fuga de aire en el de la válvula del gatillo. Problema Protector desgastado. Suciedad en la pieza del borde. Hay suciedad o daños que evitan que los sujetadores o el disparador se desplacen libremente en el cargador. El resorte del disparador está dañado. Flujo de aire hacia la herramienta incorrecto.