600KL Physician Electronic Scale With Integral Digital Height Rod 600 lb x 0.2 lb 272 kg x 0.1 kg USER INSTRUCTIONS Rev.
600KL PROFESSION AL DIGITAL PHYSICIANS SCALE WITH INTEGRAL DIGITAL HEIGHT ROD USER INSTRUCTIONS Thank you for your purchase of this Health o meter® Professional scale. Please read this manual carefully and keep it for easy reference or training. TABLE OF CONTENTS CAUTION AND WARNING ......................................................................................................2 SYMBOLS AND SPECIFICATIONS FOR THIS SCALE...........................................................
CAUTION AND WARNING To prevent injury and damage to y our scale, please follow these instructions very carefully: · · · · · · · Do not transport the scale while platform is loaded. Be sure the scale is tilted enough to assure it is rolling properly on its wheels when it is moved for cleaning or transported from one area to another. For accurate weighing the scale must be placed on a flat, stable surface.
CONNECTIVITY / CERTIFICATIONS SCALE CONNECTIVITY INF ORMATION: This scale is designed to connect to other devices via a USB port, to allow acquisition of weight, height and BMI from the scale, to help close a source of potential medical errors caused by incorrectly copying and then recording a weight taken. This scale is EMR-EHR compatible. For more information regarding how to connect this scale to your computer, a monitor or other device please contact Customer Service.
ASSEMBL Y INSTRUCTIONS – CONTINUED 3. Screw in the 4 hex screws with a 5mm hex driver. 4. Plug load cell cable into the load cell plug in base of scale (see diagram 1a). The base of the scale has been designed to provide wire management for the load cell cable. Route the load cell cable as shown in diagram 1b. Diagram 1a 5. Diagram 1b Set the base/pillar assembly upright. 6. 7. Plug the cable labeled “SCALE” into SCALE jack in display module.
SET UP Remove the protective film from the display window on the display head. Make certain that the scale base is on a stable, flat surface and that the sides of the base are clear of any obstacles. Utilizing the leveling bubble located at the top of the scale platform, level the scale by adjusting the leveling feet at each corner of the base. PREPARING THE SCALE FOR USE 1. Place the batteries in the battery holder (see “Replacing Batteries” information below). 2.
QUICK S TART OPERATING INSTRUCTIONS - CONTINUED Using the Keypad KEY FUNCTION ON / OFF Turns scale ON and OFF. ZERO Zeros the scale prior to weighing. HOLD/RELEASE Holds the value of the weighed object on the display until the button is pressed again to clear the value. UNITS Toggles between kilograms or pounds. ▲ Scrolling method for entering weight when in Calibration mode.
CALIBRATION This scale is factory calibrated and does not require calibration prior to use. The calibration procedure may be performed using a known / certified weight in either pounds or kilograms. The default is in pounds, but calibration can be done in kilograms. The following instructions assume the scale is set to pounds. If you prefer to calibrate in kilograms, please call Customer Service at 800-815-6615. Note: Calibration weight must be no less than 60 lb (27kg) and no more than 300 lb (150 kg).
TROUBLESHOOTING (CONTINUED) ERROR LIST ERROR NO. DEFINITION CHECK/REPLACE Err 1 Mathematical mistake; division by zero. Cannot calculate calibration factor Will show when trying to calibrate with no calibration weight Err 2 W eight loaded too low. Cannot calibrate While in calibration procedure add more weight in load mode Err 3 Unstable weight.
DETAILED VIEWS 9
SCALE PARTS FOR MAINTENANCE K e y# Par t# Description Qty.
SCALE PARTS FOR MAINTENANCE - Continued K e y# 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 Par t# P380610086 P380610091 P380610103 P380610080 P380610097 P215610380 P370140207 P380610104 P380610096 P380610079 P380610088 P215610310 P380610087 ADPT50 P380610093 P380610035 Description Outer Height Rod Bottom Cover Guide Block Large Guide Block COM Cable Sensor Branch PCB L Plate Sensor Branch PCB M2.
2-YEAR LIMITED WARRANTY What does the Warranty Cover? This Health o meter® Professional scale is warranted from date of purchase against defects of materials or in workmanship for a period of two (2) years. If product fails to function properly, return the product, freight prepaid and properly packed to Customer Service (see “To Get Warranty Service”, below, for instructions).
