Installation Instructions

A. POWERING ON/OFF
1.Press and hold BLUETOOTH BUTTON for 3
seconds and INDICATOR LIGHT will flash BLUE 3
times.
2. The earphone will then enter automatic pairing and
the INDICATOR LIGHT will flash RED and BLUE
alternately.
3. Enter your Bluetooth settings on your device and
connect earphones by choosing "TV HearGear BT"
or connect to your TV HearGear Streamer
4. Once connected, the INDICATOR LIGHT will flash
BLUE slowly and your earphone will be ready to use.
5. Once you complete use of your earphone, press
and hold the BLUETOOTH BUTTON for 3 seconds
and the INDICATOR LIGHT will flash RED 3 times.
Your earphones are now turned off.
B. WHILE IN USE
FOR CALLS
- Tap the BLUETOOTH BUTTON once to pick up or
end calls.
- Tap the BLUETOOTH BUTTON twice to redial the
last incoming or outgoing number.
- When there is another incoming call during a call,
tap the BLUETOOTH BUTTON once to end original
call and receive a new call. Tap the BLUETOOTH
BUTTON twice to put the original call on hold and
receive a new call. Tap BLUETOOTH BUTTON twice
to alternate between the two calls .
FOR MEDIA
- Tap BLUETOOTH BUTTON once to play/pause
music
- Tap VOLUME UP/DOWN BUTTON once to
increase/decrease media volume.
- Press and hold VOLUME UP/DOWN BUTTON for 2
seconds to skip to previous/next track.
- Press and hold BLUETOOTH BUTTON to activate
SI RI /BIXBY/ALEXA etc ... platforms.
C. SILICONE TIP FITTING PROCEDURE
1. Select the proper size ear tip to fit your ear
canal according to your best comfort.
D. BATTERY CHARGING
1.lnsert USB charging cable to an AC charger
( not included) or a computer USB port.
2.lnsert the Micro USB end into charge port.
3.The Led indicator lights up RED while the
unit is being charged. Once battery is fully
charged, the light will turn BLUE .
4.Battery charging time is approximately 2
hours.
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device
can be used in portable exposure condition without restriction.
IC WARNING
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes
aux RSS (RSS) d'Innovation, Sciences et Développement économique Canada.
Le fonctionnement est soumis aux deux conditions suivantes :
(1) Cet appareil ne doit pas causer d'interférences.
(2) Cet appareil doit accepter toutes les interférences, y compris celles susceptibles
de provoquer un fonctionnement indésirable de l'appareil.
MODEL: ERHG-BT
FCC ID: 2AU6S-HGBT
IC: 25701-HGBT
MADE IN CHINA