Owner’s Manual Installation and Operation Models: 8000TR-OAK 8000TR-OAK-IPI 8000TRLP-OAKIPI NOTICE DO NOT DISCARD THIS MANUAL • Important operating and maintenance instructions included. • Read, understand and follow these instructions for safe installation and operation. WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.
Read this manual before installing or operating this appliance. Please retain this owner’s manual for future reference. A. Congratulations This owner’s manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals. Congratulations on selecting a Heat & Glo gas fireplace, an elegant and clean alternative to wood burning fireplaces.
Safety Alert Key: • • • • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury. WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury. CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE: Used to address practices not related to personal injury. Table of Contents A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13 Finishing A. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 52 B. Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 14 Appliance Setup A. Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . C. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B. Limited Lifetime Warranty Hearth & Home Technologies LIMITED WARRANTY Hearth & Home Technologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purchased from an authorized HHT dealer and installed in the United States of America or Canada. Warranty starts with date of purchase by the original owner (End User) except as noted for replacement parts.
B. Limited Lifetime Warranty (continued) • This limited warranty does not extend to or include surface finish on the appliance or terminations, door gasketing, glass gasketing, glass discoloration, firebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or corrosion on any of the metal surfaces, cast iron components, baffles, firepots, doors, or firebox area are not covered by this warranty.
1 Listing and Code Approvals A. Appliance Certification MODELS: 8000TR-OAK, 8000TR-OAK-IPI, 8000TRLP-OAKIPI LABORATORY: Underwriters Laboratories, Inc. (UL) TYPE: Direct Vent Gas Appliance Heater STANDARD: ANSI Z21.88-2002 • CSA2.33-M02 • UL307B C. BTU Specifications US 8000TR-OAK (NG) NOTICE: This installation must conform with local codes. In the absence of local codes you must comply with the National Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A.
Note: The following requirements reference various Massachusetts and national codes not contained in this document. H.
2 Operating Instructions User Guide • Keep remote controls out of reach of children. A. Gas Fireplace Safety • Never leave children alone near a hot fireplace, whether operating or cooling down. WARNING • Teach children to NEVER touch the fireplace. HOT SURFACES! Glass and other surfaces are hot during operation AND cool down. • Consider not using the fireplace when children will be present. Hot glass will cause burns.
C. Fan Kit (optional) F. Fixed Glass Assembly If desired, a fan kit may be added. Contact your dealer to order the correct fan kit. See Section 14.H. D. Clear Space G. Remote Controls, Wall Controls and Wall Switches WARNING! DO NOT place combustible objects in front of the fireplace or block louvers. High temperatures may start a fire. See Figure 2.2.
I. Lighting Instructions (IPI) The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery life, remove them when using the transformer. FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance is equipped with an intermittent pilot ignition (IPI) device which automatically lights the burner.
J. Lighting Instructions (Standing Pilot) FOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONS 1. Open control access panel. WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING, smell all around the appliance area for gas.
K. After Fireplace is Lit Initial Break-in Procedure • The fireplace should be run three to four hours continuously on high. • Turn the fireplace off and allow it to completely cool. • Remove fixed glass assembly. See Section 14.H. • Clean fixed glass assembly. See Section 3. • Replace the fixed glass assembly and run continuously on high an additional 12 hours. This cures the materials used to manufacture the fireplace. NOTICE! Open windows for air circulation during fireplace break-in.
3 Maintenance and Service Any safety screen or guard removed for servicing must be replaced prior to operating the fireplace. Doors, Surrounds, Fronts Frequency: Annually When properly maintained, your fireplace will give you many years of trouble-free service. We recommend annual service by a qualified service technician. By: Homeowner A. Maintenance Tasks-Homeowner • Inspect for scratches, dents or other damage and repair as necessary.
Venting • Replace fireplace if firebox has been perforated. Frequency: Seasonally Control Compartment and Firebox Top By: Homeowner Frequency: Annually Tools needed: Protective gloves and safety glasses. By: Qualified Service Technician • Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow, debris, etc.
IC F CI T C U E P S D O R (Either cobrahead or SIT) P Figure 3.1 IPI Pilot Flame Patterns Figure 3.2 Standing Pilot Flame Patterns 16 Heat & Glo • 8000TR-OAK, 8000TR-OAK-IPI, 8000TRLP-OAKIPI • 2057-900 Rev.
4 Getting Started Installer Guide A. Typical Appliance System NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual HORIZONTAL TERMINATION CAP (SECTION 10.J) Note: Dual venting configurations ARE NOT allowed. Appliance MUST be vented EITHER ver tically OR horizontally. VERTICAL TERMINATION CAP (SECTION 10.
B. Design and Installation Considerations D. Inspect Appliance and Components Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required. • Carefully remove the appliance and components from the packaging. Installation MUST comply with local, regional, state and national codes and regulations.
5 Framing and Clearances NOTICE: Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY. Illustrations/diagrams are not drawn to scale. Actual installation may vary due to individual design preference. A. Selecting Appliance Location When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1). WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access.
To further prevent drafts, the wall shield and ceiling firestops should be caulked with high temperature caulk to seal gaps. Gas line holes and other openings should be caulked with high temp caulk or stuffed with unfaced insulation. If the appliance is being installed on a cement slab, a layer of plywood may be placed underneath to prevent conducting cold up into the room. B.
Combustible Mantel Legs or Wall Projections D. Mantel and Wall Projections WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing or finishing material closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc). Combustible Mantels 1 in. MIN. TOP VIEW CEILING Note: All measurements in inches. 3-1/2 in. MIN. 3 ft. MAX. 12 11 10 9 32 8 Note: Clearance from fireplace opening to perpendicular wall.
6 Termination Locations A. Vent Termination Minimum Clearances DIRECT VENT GAS, WOOD OR FUEL OIL TERMINATION WARNING B Fire Risk. Maintain vent clearance to combustibles as specified. • DO NOT pack air space with insulation or other materials. Failure to keep insulation or other materials away from vent pipe may cause overheating and fire. C A GAS TERMINATION HORIZONTAL OVERHANG 2 FT. MIN. 20 INCHES MIN.
O V N P L V R K Electrical Service E K V C Q A C V F (See Note 2) V Measure vertical clearances from this surface. B J V B V D B V i V V U.S (3 FT.) G M V A X H or i Measure horizontal clearances from this surface. V = VENT TERMINAL A B C X = AIR SUPPLY INLET = 12 inches.................clearances above grade, veranda, (See Note 1) porch, deck or balcony = 12 inches.................clearances to window or door that may be opened, or to permanently closed window.
7 Vent Information and Diagrams A. Approved Pipe DO NOT mix pipe, fittings or joining methods from different manufacturers. Vertical 12 in . The pipe is tested to be run inside an enclosed wall. There is no requirement for inspection openings at each joint within the wall. 8-1/2 in. WARNING! Risk of Fire or Asphyxiation. This appliance requires a separate vent. DO NOT vent to a pipe serving a separate solid fuel burning appliance. B.
E. Vent Diagrams Top Vent - Horizontal Termination V1 Minimum One Elbow H1 Maximum Elbow only 3 ft 924 mm 6 in. 152 mm 5-1/2 ft. 1.7 m 1 ft. 305 mm 8 ft. 2.4 m 2 ft. 610 mm 13 ft. 4.0 m 3 ft. 914 mm 18 ft. 5.5 m V1 + H1 = 40 ft. (12.2 m) Maximum H1 = 20 ft. (6.1 m) Maximum V1 Note: For corner installations: A 6 in. (152 mm) section of straight pipe may need to be attached to the appliance before a 90º elbow, to allow the vent pipe to clear the top standoffs. H1 Figure 7.
Top Vent - Horizontal Termination - (continued) Three Elbows V1 Minimum Elbow only H1 Maximum V2 Minimum H2 Maximum V1 + V2 Minimum H1 + H2 Maximum 3 ft 914 mm 1-1/2 ft. 457 mm 6-1/2 ft. 2m 2 ft. 607 mm 9-1/2 ft. 2.9 m 1 ft. 305 mm 5 ft. 1.5 m 2 ft. 610 mm 10 ft. 3.1 mm 3 ft. 914 mm 15 ft. 4.6 m 2 ft. 610 mm 10 ft. 3.1 m 1 ft. 305 mm 5 ft. 1.5 m 3 ft. 914 mm 20 ft. 6.1 m H1 + H2 = 20 ft. (6.1 m) Maximum V1 + V2 + H1 + H2 = 50 ft. (15.
Top Vent - Vertical Termination No Elbow V1 = 50 ft. Max. (15.2 m) V1 = 3 ft. Min. (914 mm) BREAK HERE Note: If installing a vertical vent/termination off the top of the appliance, the flue restrictor should be used. Figure 7.8 Flue Restrictor 3. Match the amount of vertical in the system with the chart to find the appropriate position to set the Flue Restrictor (see Figure 7.9). - CHART - V1 Figure 7.6 Installing Flue Restrictor 1. Remove Exhaust Shield using a 1/4 in.
Top Vent - Vertical Termination - (continued) V1 Two Elbows H1 Maximum One Elbow V2 V1 + V2 Minimum 3 ft 914 mm * * * 2 ft 607 mm 10 ft 3.1 m * * * 4 ft 1.2 m 20 ft 6.1 m * * * V1 + V2 + H1 = 50 ft (15.2 m) Maximum *No specific restrictions on this value EXCEPT V1 + V2 + H1 cannot exceed 50 ft (15.2 m) V2 V1 H1 Figure 7.11 V1 Three Elbows H1+ H2 V2 V1 + V2 Minimum ELBOW ONLY 3 ft 914 mm * * * 3 ft 914 mm 2 ft 610 mm 7 ft 2.1 m * * * 7 ft 2.1 m 4 ft 1.
Rear Vent - Horizontal Termination H1 = 1-1/2 ft. (457 mm) Maximum No Elbow H1 Figure 7.13 H1 = 9 in. (229 mm) Maximum One 45º Elbow This model is tested and approved to use 45º elbows in corner installations. However, 90º elbows will result in better performance. H1 Note: LP units cannot be used with a 45º elbow. A 90º elbow must be used. Figure 7.14 Heat & Glo • 8000TR-OAK, 8000TR-OAK-IPI, 8000TRLP-OAKIPI • 2057-900 Rev.
Rear Vent - Horizontal Termination - (continued) H1 Maximum Two Elbows V1 Minimum 2 ft 610 mm 4 ft 1.2 m 1-1/2 ft 6 ft 1.8 m 2-1/2 ft 8 ft 2.4 m 4-1/2 ft H2 Two 90º Elbows back to back H1+ H2 Maximum 3-1/2 ft 1.0 m 5 1/2 ft 1.7 m 457 mm 4 ft 1.2 m 8 ft 2.4 m 762 mm 6 ft 1.8 m 12 ft 3.6 m 1.4 m 12 ft 3.6 m 20 ft 6.1 m H1= 8 ft (2.4 m) Maximum V1+ H1+ H2= 50 ft (15.2 m) Maximum H1+ H2= 20 ft (6.1 m) Maximum V1 H2 H1 Figure 7.
Rear Vent - Vertical Termination One Elbow V1 Minimum H1 Maximum 6 in 152 mm 2 ft 607 mm 1-1/2 ft 457 mm 4 ft 1.2 m 2-1/2 ft 762 mm 6 ft 1.8 m 3-1/2 ft 1.0 m 8 ft 2.4 m V1+ H1= 50 ft (15.2 m) Maximum V1+ H1= 8 ft (2.4 m) Maximum V1 H1 Figure 7.17 H1+ H2 Maximum Two Elbows Two 90º Elbows back to back V1 Minimum 1/12 ft 457 mm 2 ft 610 mm 2 ft 610 mm 4 ft 1.2 m 3 ft 914 mm 5 ft 1.5 m 3-1/2 ft 1.0 m V1+ H1= 50 ft (15.
Rear Vent - Vertical Termination - (continued) Three Elbows H1 Maximum V1 Minimum H2 H1+ H2 Maximum 2 ft 610 mm 1 ft 305 mm 3-1/2 ft 1.0 m 5 1/2 ft 1.7 m 4 ft 1.4 m 1-1/2 ft 457 mm 4 ft 1.4 m 8 ft 2.4 m 8 ft 2.4 m 3-1/2 ft 1.0 m 8 ft 2.4 m 16 ft 4.9 m 8 ft 2.4 m 4-1/2 ft 1.4 m 12 ft 3.6 m 20 ft 6.1 m V1+ V2+ H1+ H2= 50 ft (15.2 m) Maximum V2 H2 V1 Figure 7.19 H1 32 Heat & Glo • 8000TR-OAK, 8000TR-OAK-IPI, 8000TRLP-OAKIPI • 2057-900 Rev.
8 Vent Clearances and Framing A. Pipe Clearances to Combustibles COMBUSTIBLE SURFACE WARNING! Risk of Fire! Maintain air space clearance to vent. DO NOT pack insulation or other combustibles: • Between ceiling firestops • Between wall shield firestops • Around vent system 3 IN. MIN. (76 mm) HEAT SHIELD Failure to keep insulation or other material away from vent pipe may cause over heating and fire. 3 in. TOP CLEARANCE Note: Slope not required. 1 in. CLEARANCE AROUND VERTICAL SECTIONS 1 in.
B. Wall Penetration Framing Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B will be required. 12 in. 10 in. 3 IN. TOP CLEARANCE HEAT SHIELD B HEAT SHIELD A* WALL SHIELD FIRESTOP WALL 1 IN.
C. Install the Ceiling Firestop A ceiling firestop MUST be used between floors and attics. • DVP pipe only - Frame an opening 10 in. by 10 in. (254 mm by 254 mm) whenever the vent penetrates a ceiling/fl oor (see Figure 8.7). ATTIC ABOVE • Frame the area with the same sized lumber as used in ceiling/floor joist. • The ceiling firestop may be installed above or below the ceiling joists when installed with a attic insulation shield. It must be under joists between floors that are not insulated.
D. Install Attic Insulation Shield WARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home Technologies Inc. requires the use of an attic shield. BEND ALL TABS INWARD 90° TO MAINTAIN CLEARANCE AND PREVENT INSULATION FROM FALLING INSIDE The National Fuel Gas Code ANSI Z223.1 and NFPA 54 requires an attic shield constructed of 26 gauge minimum metal that extends at least 2 in. (51 mm) above insulation. Attic shields must meet specified clearance and be secured in place.
9 Appliance Preparation A. Top Vent CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp. NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a later time. Figure 9.4 Fold the center parts of the retaining band up and use to remove the seal cap. Figure 9.1 Remove the cover plate by removing the four screws holding it to the top of the appliance. Remove and discard the cover plate.
B. Rear Vent NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a later time. NOTICE: Once the seal cap has been removed it CANNOT be reattached. Figure 9.6 Fold the tabs toward the center of the seal cap (90º) and remove the insulation gasket. Figure 9.9 Discard the vent cap, remove and discard the insulation basket. Figure 9.7 Cut the metal retaining band and fold the sides out. Figure 9.10 Attach the first vent section (it will snap into place).
C. Securing and Leveling the Appliance WARNING! Risk of Fire! Prevent contact with: • Sagging or loose insulation • Insulation backing or plastic • Framing and other combustible materials Block openings into the chase to prevent entry of blownin insulation. Make sure insulation and other materials are secured. DO NOT notch the framing around the appliance standoffs. Failure to maintain air space clearance may cause overheating and fire.
D. Completing Grate Set-up E. Checking Pilot Plate 1. Straighten the tabs on the grate bracket (see Figure 9.12) and remove grate from unit. 2. Remove grate bracket (see Figure 9.12) by bending it back and forth until it breaks. Discard grate bracket. Note: Ensure pilot plate is in place. This will ensure pilot stability (see Figure 9.14) 3. Remove 4 tabs holding base refractory (see Figure 9.12) by bending tabs back and forth until they break. PILOT PLATE 4. Reinstall grate into unit (see Figure 9.
10 Installing Vent Pipe A. Assemble Vent Sections Attach Vent to the Firebox Assembly Note: The end of the pipe sections with the lanced tabs will face toward the appliance. Attach the first pipe section to the starting collar: • Lanced pipe end to the starting collar • Inner pipe over inner collar • Push the pipe section until all lanced tabs snap in place • Lightly tug on pipe to confirm it has locked.
B. Assemble Slip Sections C. Secure the Vent Sections • Slide the inner flue of the slip section into the inner flue of the pipe section and the outer flue of the slip section over the outer flue of the pipe section. See Figure 10.6. • Vertical runs must be supported every 8 ft. (2.44 m) after the 25 ft. (7.62 m) maximum unsupported rise. • Slide together to the desired length. • Horizontal sections must be supported every 5 feet (1.52 m).
D. Disassemble Vent Sections • Rotate either section (see Figure 10.10) so the seams on both pipe sections are aligned as shown in Figure 10.11. • Pull carefully to separate the pieces of pipe. Figure 10.10 Rotate Seams for Disassembly Figure 10.11 Align and Disassemble Vent Sections Heat & Glo • 8000TR-OAK, 8000TR-OAK-IPI, 8000TRLP-OAKIPI • 2057-900 Rev.
E. Install Metal Roof Flashing Note: Skip this section if using the RF4-8. • See minimum vent heights for various pitched roofs (Figure 10.14) to determine the length of pipe to extend through the roof. CAULK • Slide the roof flashing over the pipe sections extending through the roof as shown in Figure 10.15. HORIZONTAL OVERHANG 2 FT. MIN. 20 INCHES MIN. VERTICAL WALL LOWEST DISCHARGE OPENING Figure 10.15 F.
G. Install RF4-8 The RF4-8 may be used in place of the roof flashing and storm collar (Sections 10.G. and 10.H.) Pipe must be supported within 12 inches of the roofline using plumbers strapping or an SLP-FS when using the RF4-8 Flashing. Refer to Section 10.D. Secure Vent Sections. SECURE WITH 4 SCREWS NO LONGER THAN 1 IN. (25 MM) Figure 10.20 Apply Sealant SLP-FS Figure 10.18 Secure Pipe with SLP-FS • Trim the rubber boot (using scissors or a utility knife), cutting along the marked measurement lines.
H. Install Vertical Termination Cap • Attach the vertical termination cap by sliding the inner collar of the cap into the inner flue of the pipe section while placing the outer collar of the cap over the outer flue of the pipe section. • Secure the cap by driving three self-tapping screws (supplied) through the pilot holes in the outer collar of the cap into the outer flue of the pipe (see Figure 10.23). TERMINATION CAP I.
J. Install Horizontal Termination Cap WARNING! Risk of Fire! The telescoping flue section of the termination cap MUST be used when connecting vent. • 1-1/2 (38 mm) minimum overlap of flue telescoping section is required. Failure to maintain overlap may cause overheating and fire. Note: When using termination caps with factory-supplied heat shield attached, no additional wall shield firestop is required on the exterior side of a combustible wall. HEAT SHIELD OR EXTENDED HEAT SHIELD HEAT SHIELD 1-1/2 IN.
11 Gas Information A. Fuel Conversion C. Gas Connection • Make sure the appliance is compatible with available gas types. • Refer to Reference Section 16 for location of gas line access in appliance. • Conversions must be made by a qualified service technician using Hearth & Home Technologies specified and approved parts. • Gas line may be run through knockout(s) provided. B. Gas Pressure • Optimum appliance performance requires proper input pressures.
12 Electrical Information A. Wiring Requirements B. Intellifire Ignition System Wiring NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electric Code CSA C22.1. • Wire the appliance junction box to 110 VAC for proper operation of the appliance. • Wire the appliance junction box to 110-120 VAC.
INTERMITTENT PILOT IGNITOR I IGNITION MODULE 3 VAC PLUG-IN 3V TRANSFORMER S ON/OFF WALL SWITCH FLAME SPARKER/ SENSOR IGNITION MODULE (3V) WHT ORG BLACK RED BLACK WIRE CAN BE PLUGGED INTO ANY OF #1 - #5 LOCATIONS ON THE HOT SIDE PIGGYBACK ON/OFF SWITCH GRN WHITE WIRE CAN BE PLUGGED INTO ANY OF #1- #5 LOCATIONS ON THE NEUTRAL SIDE TRANSFORMER 3 VAC ORG GROUND REMOTE CONTROL HOT GROUND TO FIREPLACE CHASSIS BRN NEUTRAL LOW VOLTAGE SEE NOTE 1 BRN VALVE BATTERY PACK PLUG IN VALVE Figure 12.
F. Junction Box Installation If the box is being wired from the INSIDE of the appliance: Romex Connector • Remove the screw attaching the junction box/receptacle to the outer shell, rotate the junction box inward to disengage it from the outer shell (see Figure 12.4). 14/2WG • Pull the electrical wires from outside the appliance through the opening into the valve compartment and secure wires with a Romex connector. See Figure 12.4.
13 Finishing A. Mantel and Wall Projections B. Facing Material WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc.) Failure to comply could cause fire. • Metal front faces may be covered with non-combustible materials only. • Facing and/or finishing materials must never overhang into the glass opening.
14 Appliance Setup A. Remove Fixed Glass Assembly F. Ember Placement See Section 14.H. WARNING! Risk of Explosion! Follow ember placement instructions in manual. DO NOT place embers directly over burner ports. Replace ember material annually. Improperly placed embers interfere with proper burner operation. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the firebox. C.
G. Install the Log Assembly If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately, refer to the following instructions. B LOG TABS A A CAUTION: Carefully remove the logs from the packaging. Logs are fragile! B A B B STEP 1: Remove metal grate supports (A) and refractory tabs (B) by using a back and forth motion until the tabs break free. Metal tabs and supports are needed for shipping only.
5 3 STEP 5: (SRV2057-723): Mate the top of log 4 with the right metal tab on log 3. The bottom of log 4 should touch the inside face of the right grate tine. 5 1 2 1 2 4 3 STEP 6: (SRV2057-724): Notch in left end of Log 5 will interlock with front left corner of grate. Rest right end of log so that it engages tab on log 3. Log 2 may need to shift to right slightly. 3 C 2 C 5 6 3 4 1 2 6 1 STEP 7: (SRV2057-725): Place log 6 on log 2 as shown.
H. Fixed Glass Assembly L. Air Shutter Setting WARNING! Risk of Asphyxiation! Handle fixed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches. Air shutter settings should be adjusted by a qualified service technician at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shutter for longer vertical runs. See Figure 14.3. • DO NOT strike, slam or scratch glass.
15 Troubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualified service technician in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. Contact your dealer to arrange a service call by a qualified service technician. A.
Troubleshooting (continued) Symptom 3. (Continued) Possible Cause Corrective Action C. Valve. Turn the valve knob to the ON position. Place the ON/ OFF switch in the ON position. Take a reading with a millivolt meter at the thermopile terminals. The millivolt meter should read greater than 125mV. If the reading is acceptable, and if the burner does not come on, replace the gas valve. D. Plugged burner orifice. Check the burner orifice for stoppage. Remove stoppage. E. Wall switch or wires.
B. Intellifire Ignition System Symptom Possible Cause 1. Pilot won’t light. A. Incorrect wiring. The ignitor/module makes noise, but no B. Loose connections or electrical spark. shorts in the wiring. 2. Pilot won’t light, there is no noise or spark. 3. Pilot sparks, but Pilot will not light. Corrective Action Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are connected to correct terminals on module and pilot assembly.
Intellifire Ignition System - (continued) Symptom Possible Cause 4. Pilot lights but continues to spark, and main burner will not ignite. (If the pilot continues to spark after the pilot flame has been lit, flame rectification has not occurred.) 60 A. A shorted or loose connection in flame sensing rod. Corrective Action Verify all connections to wiring diagram in manual. Verify connections underneath pilot assembly are tight.
16 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.
B. Vent Components Diagrams Pipe DVP4 Effective Height/Length DVP Pipe (see chart) Effective Length Inches Millimeters 4 102 10-1/2 in. (267 mm) 45 ° DVP6 6 152 DVP12 12 305 DVP24 24 610 DVP36 36 914 DVP48 48 1219 10-7/8 in. (276 mm) DVP45 (45º Elbow) 4-7/8 in. ( 276 mm) DVP6A 3 to 6 76 to 152 DVP12A 3 to 12 76 to 305 DVP12MI 3 to 12 76 to 305 DVP24MI 3 to 24 76 to 610 11-3/8 in. (289 mm) 10 in. (254 mm) 10 in. (254 mm) 1 in. (25 mm) 7-3/8 in. (187 mm) 24 in.
B. Vent Components Diagrams (continued) Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B will be required. 8 in. (203 mm) Heat Shield 15-1/8 in. (384 mm) Term Cap 12 in.
B. Vent Components Diagrams (continued) 31 in. (787 mm) 13-1/4 in. (367 mm) 24-5/8 in. (625 mm) 27-1/2 in. (127 mm) 24-5/8 in. (625 mm) 13-1/4 in. (367 mm) RF6M Roof Flashing Multi-pak RF12M Roof Flashing Multi-pak 5 in. (127 mm) 13-3/4 in. (349 mm) 11-7/8 in. (302 mm) 13-7/8 in. (352 mm) 13-3/4 in. (349 mm) DVP-BEK2 DVP-HPC Cap Brick Extension BEK Trap Cap Brick Extension 11-5/8 in. (295 mm) 12-1/8 in. (308 mm) 7-1/8 in. (181 mm) 5-3/4 in.
B. Vent Components Diagrams (continued) 7-3/8 in. (187 mm) 1-1/2 in. (38 mm) 3-7/8 in. (98 mm) 17-3/4 in. (451 mm) 14 in. (356 mm) 10-1/2 in. (267 mm) DVP-TV VerticalTermination Cap 12 in. (305 mm) 12 in. 305 mm DVP-TB1 BasementVent Cap 7-1/4 in. (184 mm) 12-1/2 in. (318 mm) 5-1/4 in. (133 mm) DVP-TVHW VerticalTermination Cap (Highwind) 14 in. (356 mm) 16-7/8 in. (429 mm) 12 in. (305 mm) 7-1/8 in. (181 mm) 12-1/8 in. (314 mm) 8-3/4 in. (222 mm) PVK-80 (For use with IPI and DSI appliances only.
C. Service Parts 8000TR-OAK, 8000TR-OAK-IPI Beginning Manufacturing Date: Feb. 2006 Ending Manufacturing Date: ______ Service Parts Diagram 7 10 8 11 9 12 13 Log Set Assembly 5 2 3 6 Part number list on following page. 66 Heat & Glo • 8000TR-OAK, 8000TR-OAK-IPI, 8000TRLP-OAKIPI • 2057-900 Rev.
Service Parts List 8000TR-OAK, 8000TR-OAK-IPI IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.
8000TR-OAK-IPI Service Parts Beginning Manufacturing Date: Feb. 2005 Ending Manufacturing Date: ______ Valve Assembly Diagram/ Parts List 2 Intermittent Pilot Ignition Valve Assembly 3 1 4 5 7 6 11 10 8 9 IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.
8000TR-OAK Service Parts Beginning Manufacturing Date: Feb. 2005 Ending Manufacturing Date:______ Valve Assembly Diagram/ Parts List 2 1 Standing Pilot Ignition Valve Assembly 3 4 5 6 7 9 8 10 11 IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.
D. Contact Information Heat & Glo, a brand of Hearth & Home Technologies Inc. 7571 215th St, Lakeville, MN 55044 www.heatnglo.com Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer, please visit www.heatnglo.com.