Owner’s Manual Installation and Operation Models: Aztec Bravo CAUTION DO NOT DISCARD THIS MANUAL • Important operating and maintenance instructions included. • Read, understand and follow these instructions for safe installation and operation. WARNING If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.
Read this manual before installing or operating this appliance. Please retain this owner’s manual for future reference. Congratulations Congratulations on selecting a Hearth & Home Technologies gas appliance —an elegant and clean alternative to wood burning appliances. The Hearth & Home Technologies gas appliance you have selected is designed to provide the utmost in safety, reliability, and efficiency. This Owner’s Manual should be retained for future reference.
- Table of Contents - Section 1: Listing and Code Approvals Section 9: Gas Information A. Fuel Conversions ...................................... 26 B. Gas Pressures .......................................... 26 C. Gas Connection ........................................ 26 Section 10: Electrical Information A. Recommendation for Wire ........................ 28 B. Connecting to the Appliance ..................... 28 C. Intellifire Ignition System Wiring................ 28 D. Wall Switch (Required) ...
1 A. Listing and Code Approvals Appliance Certification C. MODELS: Aztec, Bravo BTU Specifications Maximum Input BTUH Orifice Size (DMS) US (0-2000 FT) 23,000 42 CANADA (2000-4500 FT) 20,700 43 US (0-2000 FT) 23,000 53 CANADA (2000-4500 FT) 20,700 54 Models (U.S. or Canada) LABORATORY: Underwriters Laboratories, Inc. (UL) TYPE: Direct Vent Gas Appliance Heater Aztec, Bravo (NG) STANDARD: ANSI Z21.88-2000•CSA2.
2 Getting Started A. Design and Installation Considerations C. Inspect Appliance and Components Hearth & Home Technologies direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required. WARNING Check building codes prior to installation. Inspect appliance and components for damage. Damaged parts may impair safe operation. • Do NOT install damaged components.
3 Framing and Clearances NOTE: • Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY. • Illustrations/diagrams are not drawn to scale. • Actual installation may vary due to individual design preference. WARNING Fire Risk Provide adequate clearance: • Around air openings • To combustibles • For service access Locate appliance away from traffic areas. A.
B. high temp caulk or stuffed with unfaced insulation. If the appliance is being installed on a cement slab, a layer of plywood may be placed underneath to prevent conducting cold up into the room. Constructing the Appliance Chase A chase is a vertical boxlike structure built to enclose the gas appliance and/or its vent system. Vertical vents that run on the outside of a building may be, but are not required to be, installed inside a chase. C.
D. Mantel Projections Note: All measurements in inches. 31 CEILING 1 INCH MINIMUM TO VENT PIPE 18 17 16 15 14 13 9 1/8 MIN. 12 11 10 3 1/8 9 8 Figure 3.4 7 6 3 7/8 Clearances to Mantel Legs or Wall Projections (Acceptable on both sides of opening.) 5 TOP OF FINISHING STRIP Figure 3.3 8 TOP OF UNIT Clearances to Mantels or other Combustibles above Appliance Hearth & Home Technologies • Bravo, Aztec • InD • 703-900 Rev.
4 A. Termination Locations Vent Termination Minimum Clearances WARNING Fire Risk. Explosion Risk. Maintain vent clearance to combustibles as specified. • Do not pack air space with insulation or other materials. Failure to keep insulation or other materials away from vent pipe may cause fire. H (MIN.) - MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING Measure vertical clearances from this surface. Roof Pitch H (Min.) Ft. Flat to 6/12...........................................................1.
M N P R Q (See Note 2) V T V S Electrical Service S V D* V V = VENT TERMINAL A X = AIR SUPPLY INLET = 12 inches ...............clearances above grade, veranda, (See Note 1) porch, deck or balcony = 12 inches ...............clearances to window or door that may be opened, or to permanently closed window. (Glass) = 18 inches ...............vertical clearance to unventilated soffit or to ventilated soffit located above the terminal *30 inches ..............
5 Vent Information and Diagrams A. Vent Table Key The abbreviations listed in this vent table key are used in the vent diagrams. Description V2 Second section of vertical length H1 First section (closest to appliance) of horizontal length H2 Second section of horizontal length Vertical 8-1/2 in. First section (closest to appliance of vertical length in . V1 12 Symbol 8-1/2 in. WARNING Fire Hazard. Explosion Risk. Asphyxiation Risk.
D. Vent Diagrams WARNING Fire Risk. Explosion Risk. Do NOT pack insulation or other combustibles between ceiling firestops. • ALWAYS maintain specified clearances around venting and firestop systems. • Install wall shield and ceiling firestops as specified. Failure to keep insulation or other material away from vent pipe may cause fire. 1. Top Vent - Horizontal Termination One Elbow V1 Minimum H1 Maximum 3 ft. 0.9 m 2 ft. 0.6 m 4 ft. 1.2 m 4 ft. 1.2 m 5 ft. 1.5 m 6 ft. 1.8 m 12 ft. 3.
1. Top Vent - Horizontal Termination - (continued) Three Elbows V1 + V2 Minimum Í H1 + H2 Maximum 3 ft. 0.9 m 2 ft. 0.6 m 4 ft. 1.2 m 4 ft. 1.2 m 5 ft. 1.5 m 6 ft. 1.8 m 12 ft. 3.7 m 20 ft. 6.1 m V1 + V2 + H1 + H2 = 40 ft. (12.2 m) Maximum H1 + H2 = 20 ft. (6.1 m) Maximum NOTE: V 1 MUST be a minimum of 3 feet. NOTE: The first elbow used MUST always be DVP90ST. Figure 5.5 Hearth & Home Technologies, Inc. • Bravo, Aztec • InD • 703-900 Rev.
2. Top Vent - Vertical Termination No Elbow V1 = 46 ft. Max. (14.0 m) 8 FT. (2.4mm) FLUE OUTLET Note: A 45O elbow may be attached directly to starting collars on unit only if used in conjunction with a return 45O elbow AND terminating vertical with V = 8 feet MINIMUM. A straight section of pipe can be used between the two 450 elbows. Figure 5.6 14 Hearth & Home Technologies • Bravo, Aztec • InD • 703-900 Rev.
Two Elbows V1 Minimum H1 Maximum 3 ft. 0.9 m 2 ft. 0.6 m * 4 ft. 1.2 m 4 ft. 1.2 m * 5 ft. 1.5 m 6 ft. 1.8 m * 12 ft. 3.7 m 20 ft. 6.1 m * Í V2 V1 + V2 + H1 = 40 ft (12.2 m) Maximum *No specific restrictions on this value EXCEPT V1 + V2 + H1 cannot exceed 40 ft (12.2 m) NOTE: V 1 MUST be a minimum of 3 feet. NOTE: The first elbow used MUST always be DVP90ST. Figure 5.7 Hearth & Home Technologies, Inc. • Bravo, Aztec • InD • 703-900 Rev.
2. Top Vent - Vertical Termination - (continued) V1 Three Elbows H1 + H2 V2 3 ft. 0.9 m 2 ft. 0.6 m * 4 ft. 1.2 m 4 ft. 1.2 m * 5 ft. 1.5 m 6 ft. 1.8 m * 12 ft 3.7 m 20 ft. 6.1 m * H1 + H2 = 20 ft (6.1 m) Maximum *No specific restrictions on this value EXCEPT V1 + V2 + H1 + H2 = 40 ft (12.2 m) Maximum NOTE: V 1 MUST be a minimum of 3 feet. NOTE: The first elbow used MUST always be DVP90ST. INSTALLED HORIZONTALLY Figure 5.
6 Vent Clearances and Framing B. Wall Penetration Framing A. Pipe Clearances to Combustibles WARNING Fire Risk. Explosion Risk. Maintain vent clearance to combustibles as specified. 10 in. 12 in. • Do not pack air space with insulation or other materials. Failure to keep insulation or other materials away from vent pipe may cause fire. B NOTE: Slope not required. 3 in. TOP CLEARANCE A 1 in. CLEARANCE AROUND VERTICAL SECTIONS 1 in. SIDE AND BOTTOM CLEARANCE A* Figure 6.1 Pipe Clearances 77 in.
C. Vertical Penetration Framing WARNING Fire Hazard Keep loose materials or blown insulation from touching the vent pipe. • National building codes recommend using attic shield to keep loose materials/ blown insulation from contacting vent. • Hearth & Home Technologies requires the use of an attic shield. ATTIC ABOVE Installing the Ceiling Firestop A • Frame an opening 10 inches by 10 inches whenever the vent system penetrates a ceiling/floor (see Figure 6.3).
7 A. Appliance Preparation Securing and Leveling the Appliance WARNING Fire Risk. • Prevent contact with sagging, loose insulation. • Do NOT install against combustible materials such as exposed insulation, plastic and insulation backer. CAUTION Sharp Edges • Wear protective gloves and safety glasses during installation. The diagram shows how to properly position, level, and secure the appliance (see Figure 7.1). Nailing tabs are provided to secure the appliance to the framing members.
8 Installing Vent Pipe A. Assembly of Vent Sections WARNING Fire Risk Exhaust Fumes Risk Impaired Performance of Appliance • Overlap pipe slip sections at least 1-1/2 inches. • Use pilot holes for screws. • Screws must not exceed one inch long. • Pipe may separate if not properly joined. Figure 8.1 Attaching Vent to the Firebox Assembly To attach the first pipe section to the collars, slide the male end of the inner vent of the pipe section over the inner collar on the firebox assembly.
Assembling Minimum Installations (MI) Sections MI sections are non-unitized so that they can be cut to a certain length. Cut these sections to length from the nonexpanded end (see Figure 8.5). They can then be attached by first connecting the expanded end of the MI inner flue with the inner pipe from the adjacent pipe section and securing with three screws. The expanded portion of the MI inner flue must overlap completely with the unexpanded end of the adjacent pipe section.
Securing the Vent Sections Vertical Sections Vertical sections of pipe must be supported every 8 feet after the 25 foot maximum unsupported rise. The vent support or plumber’s strap (spaced 120° apart) may be used to do this (see Figure 8.8). Horizontal Sections Horizontal sections of vent must be supported every 5 feet with a vent support or plumber’s strap. Figure 8.8 Securing Vertical Pipe Sections Figure 8.9 Securing Horizontal Pipe Sections B.
C. Installing Heat Shield and Horizontal Termination Cap WARNING Installing the Horizontal Termination Cap Vent termination must not be recessed in the wall. Siding may be brought to the edge of the cap base. Fire Hazard Impaired performance of appliance • Telescoping flue section of termination cap MUST be used when connecting pipe section to termination cap. • Maintain a 1-1/2 inch minimum overlap on telescoping flue section of termination cap.
D. Installing Roof Flashing and Vertical Termination Cap To install roof flashing see Figure 8.13. For installation of vertical termination cap see minimum vent heights for various pitched roofs (see Figure 8.13) . To attach the vertical termination cap, slide the inner collar of the cap into the inner flue of the pipe section and place the outer collar of the cap over the outer flue of the pipe section. Secure with three screws into the outer flue.
Assembling and Installing Storm Collar CAUTION Sharp Edges • Wear protective gloves and safety glasses during installation. Connect both halves of the storm collar with two screws (see Figure 8.15). Wrap the storm collar around the exposed pipe section and align brackets. Insert a bolt (provided) through the brackets and tighten nut to complete storm collar assembly (see Figure 8.16). Figure 8.
9 Gas Information A. Fuel Conversions C. Before making gas connections ensure that appliance being installed is compatible with the available gas type. Any natural or propane gas conversions necessary to meet the appliance and locality needs must be made by a qualified technician using Hearth & Home Technologies specified and approved parts. B. Gas Pressures Proper input pressures are required for optimum appliance performance. Gas line sizing requirements need to be made following NFPA51.
• • Ensure that gas line does not come in contact with outer wrap of appliance. Follow local codes. HIGH ALTITUDE INSTALLATIONS Incoming gas line should be piped into the valve compartment and connected to the 1/2 inch connection on the manual shutoff valve. U.L. Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U.S.A. and Canada. WARNING Fire or Explosion Hazard • • • • • Gas buildup during line purge may ignite.
10 Electrical Information A. Recommendation for Wire C. Intellifire Ignition System Wiring This appliance requires 110-120 VAC be wired to the junction box either for proper operation of the appliance (Intellifire ignition). This appliance requires a 110 VAC supply to the appliance junction box for operation. A wiring diagram is shown in Figure 10.2.
SPARK TO PILOT IGNITOR FAN OUTLET RECEPTACLE (NO FAN OPTION) IGNITOR MODULE 3V 3 V I PLUG-IN 3V TRANSFORMER S TRANSFORMER 3 V 3V LOWVOLTA VOLTAGE LOW G E SEENOTE NOTE1 1 SEE IGNITION MODULE (3V) BLACK BLACK (IGNITOR) (IGNITO R ) BLACK (SENSOR) PILOT LY PILOT ASSEMB ASSEMBLY LY AND VALVE VALVEASSEMB ASSEMBLY MUST BE GROUNDED (COMMON GROUND GROUNDTO WITH FIREPLACE FIREPLACE CHASSIS) CHASSIS BLACK WALL WA L LSWITCH SWITCH BLACK 2045-024 2012-206 ORANGE VALVE LOW VOLTAGE LOW VOLTA G E SEE NOTE 1 SEE
E. Junction Box Installation Romex Connector If the box is being wired from the OUTSIDE of the appliance: Remove the cover plate located on the outer shell - right side (see Figure 10.3). • Install the supplied Romex™ connector in the cover plate. • Feed the necessary length of wire through the connector. 14/2WG Cover Plate outside firebox HT W WHT B LK BLK • • Make all necessary wire connections and reattach the cover plate to the outer shell.
11 Finishing A. Mantel Projections Figure 11.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance. 1/2 INCH NON-COMBUSTIBLE BOARD REQUIRED ON UNIT FACE 31 CEILING 1 INCH MINIMUM TO VENT PIPE 18 17 16 15 14 13 9 1/8 MIN.
C. Finishing Styles • This model has multiple installation and finishing options. The following section describe three basic installations. CAUTION Note: A 1/2 inch clearance must be maintained between combustible materials and the front face of the fireplace. OPTION A: Flush Wall Finish Kiva-style finished in a straight wall (see Figure 11.4).
NOTE: Previous numbers are for combustible construction numbers. Arch may protrude up to 5-1/2 inches maximum as measured from unit front face. OPTION C: SOUTHWESTERN kiva-style The third installation option illustrated is a corner-installation with custom finishing. This option requires advanced finishing methods involving either combustible or non-combustible construction materials (see Figure 11.7). NOTE: The kiva-style arch depth may be any size if using noncombustible materials i.e.
Í OPTION D: Flush Wall Finish with Luxor Surround Kiva-style finished in a straight wall (see Figure 11.8). 3-in. GAP SHEETROCK EDGE FINISHING STRIP Figure 11.8 Flush wall installation with Luxor Surround • Unit is installed using framing dimensions found in Figure 3.2. • Do not use nailing tabs provided on unit sides for Option D. • Nailing tabs found in manual bag assembly or in cardboard sleeve of packing. Install nailing tabs using screws on upper unit sides (see Figure 11.3).
12 Appliance Setup A. Remove Shipping Materials Placing the Ember Material Remove shipping materials from inside or underneath the firebox. Ember material is shipped with this gas appliance. To place the ember material: • Embers CANNOT be placed directly over ports. B. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity. C. Accessories Install approved accessories per instructions included with accessories.
E. Positioning the Logs If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately, refer to the following instructions. CAUTION: Logs are fragile! Carefully remove the logs from the packaging. Before placing logs, remove shipping bracket and tie straps from the burner and grate. Place the lava rock on the bottom of the firebox. Evenly spread out the lava rocks with your hand.
GROOVES FOR LOG #4 1 1 3 3 1 2 2 2 Figure 12.9 Figure 12.8 LOG #3 (SRV703-703): Place log #3 flush with grate tines 1 and 2. The right end of the log should make contact with grate tine 2. FLAT SPOT FOR LOG #5 4 4 2 Figure 12.11 Figure 12.10 LOG #4 (SRV750-705): Place the top of log #4 in the groove in log #1. Place the base of the log into the groove on log #3 such that the end of the log contacts grate tine 2. 5 5 Figure 12.12 4 Figure 12.
GROOVES FOR LOG #7 6 3 6 Figure 12.15 Figure 12.14 LOG #6 (SRV750-706): Place log #6 in the groove in log #3. Log #6 must be placed parallel to the burner ports behind the log. CAUTION: If log #6 is not parallel to burner ports then sooting may occur. Do not place logs directly on burner ports. FLAT SPOT FOR LOG #8 2 7 7 1 Figure 12.17 Figure 12.16 LOG #7 (SRV750-704): Place the top portion of log #7 into the groove on log #1 and place the bottom of the log in the groove in log #2.
Positioning the Logs If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately, refer to the following instructions. Log Assembly: LOGS-BRAVO CAUTION: Logs are fragile! Carefully remove the logs from the packaging. Before placing logs, check that the sensor on the pilot assembly does not contact the burner. Remove shipping bracket and tie straps from the burner and grate. 2 4 1 5 6 3 Place the lava rock on the bottom of the firebox.
2 RIGHT GRATE TINE 2 LOG #2 (SRV750-705): Place the top of log #2 in the groove on log #1. Place the base of the log on the inside of the outer right grate tine with the grate tine fitting in the groove on log #2. GROOVE FOR LOG #4 3 3 LOG #3 (SRV750-706): Place log #3 with the base on the inner right grate tine. The top of the log should be placed so that it doesn’t cover any ports on the burner.
GROOVE FOR LOG #6 5 5 LOG #5 (SRV704-702): Place log #5 on right side of the grate. Position the base of the log on the log tab. The log tab should insert into slot feature on back side of log. Place the top of the log into the groove on log #1. 6 6 LOG #6 (SRV704-701): Place log #6 on left side of grate. Position the base of the log on the log tab. Log tab should insert into slot feature on back side of log. Place the top of the log into flat spot on log #1. Hearth & Home Technologies, Inc.
F. Glass Assembly G. Grilles and Trim WARNING Handle glass doors with care. • Inspect the gasket to ensure it is undamaged. Install optional marble and brass trim surround kits as desired. Marble, brass, brick, tile, or other noncombustible materials can be used to cover up the gap between the sheet rock and the appliance. Shutter Settings • Inspect the glass for cracks, chips or scratches. Burner • Do NOT strike, slam or scratch glass.
13 Operating Instructions A. Before Lighting Appliance This appliance has an Intellifire ignition system. CAUTION If installing Intellifire ignition battery backup: • Do not install batteries if the backup mode may not be used for extended time. • Batteries may leak. • Install batteries only when needed for power outage. WARNING HOT! DO NOT TOUCH. SEVERE BURNS MAY RESULT. CLOTHING IGNITION MAY RESULT. Glass and other surfaces are hot during operation and cool down. • Keep children away.
B. Lighting Appliance Intellifire Ignition FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance is equipped with • Do not touch any electric switch; do not use any phone in your building. an intermittent pilot ignition (IPI) device which automatically lights • Immediately call your gas supplier the burner. Do not try to light the from a neighbor’s phone.
C. After Appliance is Lit Initial Break-in Procedure When you light the appliance, you may notice that it produces heat which does have an associated odor or smell. If you feel this odor is excessive it may require the initial three to four hour continuous burn on high followed by a second burn up to 12 hours to fully drive off any odor from paint and lubricants used in the manufacturing process. Condensation of the glass is normal.
14 Troubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. A. Intellifire Ignition System Sympton 1. The ignitor/module makes noise, but no spark. 2.
Intellifire Ignition System - (continued) Symptom Possible Cause Corrective Action 3. (Continued) - Pilot lights b. Poor flame rectification or contaminated but continues to spark, sensor rod. and main burner will not ignite. (If the pilot continues to spark after the pilot flame has been lit, flame rectification has not occurred.) Verify that flame is engulfing sensor rod. If the pilot assembly does not have a ground strap, consider installing one to increase flame rectification.
15 Maintaining and Servicing Appliance Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualified service technician should perform an appliance checkup at the beginning of each heating season. WARNING Risk of injury or property damage. Before servicing: • Turn off gas. • Turn off electricity to appliance. • Disable remote control, if one is present. • Ensure appliance is completely cooled.
Inspect Doors, Surrounds and Fronts Mantenance Tasks 1. Assess condition of screen and replace as necessary. Recommend addition of screen if one is not present. 2. Inspect for scratches, dents or other damage and repair as necessary. 3. Verify no obstructions to airflow through the louvers. 4. Verify maintenance of proper clearance to combustible household objects. Gasket Seal, Glass Assembly and Glass 1. Inspect gasket seal and its condition. 2.
16 Î Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.
B. Vent Components Diagrams Pipe Effective Height/Length DVP Pipe (see chart) Effective Length Inches Millimeters 4 102 DVP4 DVP6 6 152 DVP12 12 305 DVP24 24 610 DVP36 36 914 DVP48 48 1219 DVP6A 3 to 6 76 to 152 DVP12A 3 to 12 76 to 305 DVP12MI 3 to 12 76 to 305 DVP24MI 3 to 24 76 to 610 10-1/2 in. (267 mm) 45° 4-7/8 in. ( 276 mm) 10-7/8 in. (276 mm) DVP45 (45 ° Elbow) 11-3/8 in. (289 mm) 10 in. (254 mm) 10 in. (254 mm) 1 in. (25 mm) 7-3/8 in. (187 mm) 24 in.
B. Vent Components Diagrams (continued) 8 in. (203 mm) Max Effective Length 15-1/8 in. (384 mm) EFFECTIVE LENGTH Term Cap 14 in. (566 mm) Minimum Maximum Trap1 4-1/8 in. (105 mm) 5-5/8 in. (143 mm) Trap2 6-3/4 in. (171 mm) 10-5/8 in. (270 mm) DVP-TRAP SERIES Horizontal Term Cap DVP-TRAP1 DVP-TRAPK2 DVP-Trap2 DVP-TRAPK1 DVP-VTI DVP-TH Figure 16.3 DVP vent components 52 Hearth & Home Technologies • Bravo, Aztec • InD • 703-900 Rev.
B. Vent Components Diagrams (continued) 7-3/8 in. (187 mm) 1-1/2 in. (38 mm) 3-7/8 in. (98 mm) 14 in. (356 mm) 17-3/4 in. (451 mm) 10-1/2 in. (267 mm) DVP-TV Vertical Termination Cap 12 in. (305 mm) DVP-TB1 Basement Vent Ca p 31 in. (787 mm) 13-1/4 in. (367 mm) 24-5/8 in. (625 mm) 27-1/2 in. (127 mm) 24-5/8 in. (625 mm) 13-1/4 in. (367 mm) RF6M Roof Flashing Multi-pak 13-3/4 in. (349 mm) RF12M Roof Flashing Multi-pak 5 in. (127 mm) 7-1/4 in. (184 mm) 12-1/2 in. (318 mm) 13-3/4 in.
AZTEC C. Service Parts List Beginning Manufacturing Date: 3-02 Ending Manufacturing Date: ______ (NG, LP) Exploded Parts Diagram 3 19 7 18 1 6 17 4 5 2 8 Log Set Assembly 13 14 11 9 12 16 10 Part number list on following page. 54 Hearth & Home Technologies • Bravo, Aztec • InD • 703-900 Rev.
Service Parts List AZTEC IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealer’s VIP site. When ordering, supply serial and model numbers to ensure correct service parts.
BRAVO Service Parts (NG, LP) Exploded Parts Diagram Beginning Manufacturing Date: 3-02 Ending Manufacturing Date: ______ 17 3 7 16 1 6 4 5 2 15 8 Log Set Assembly 9 14 12 11 10 Part number list on following page. 56 Hearth & Home Technologies • Bravo, Aztec • InD • 703-900 Rev.
Service Parts List BRAVO IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealer’s VIP site. When ordering, supply serial and model numbers to ensure correct service parts.
AZTEC, BRAVO Service Parts Beginning Manufacturing Date: 3-02 Ending Manufacturing Date: _____ (NG, LP) Exploded Parts Diagram 3 Intermittent Pilot Ignition Valve Assembly 4 8 1 6 5 2 7 AVAILABLE TO SHIP IN 24 HOURS ITEM 58 DESCRIPTION 1 Jumper Wire 2 Wire Assembly Thermostat Wire Assembly 3 SERIAL # PART NUMBER 2012-206 Y 593-596A 2045-024 Y Y Flex Ball Valve Assembly 302-320A Y 4 Valve NG 593-500 Y 4 Valve LP 593-501 Y 5 Module 593-592 Y 6 Wire Assembly 593-590A Y
D. Limited Lifetime Warranty LIMITED LIFETIME WARRANTY BRAVO GAS APPLIANCE PRODUCTS BASIC ONE-YEAR WARRANTY. HEAT & GLO, a brand of HEARTH & HOME TECHNOLOGIES INC., located at 20802 Kensington Boulevard, Lakeville, MN 55044, (“HEAT & GLO”) warrants to the original owner that your new HEAT & GLO Gas Appliance (the “Product”) will be free from defects in materials and workmanship for a period of one year from the date of installation.
Limited Lifetime Warranty Aztec Gas Appliance (Fireplace) Limited Lifetime Warranty HEARTH & HOME TECHNOLOGIES INC. (“HHT”) extends the following warranty for HEATILATOR® gas appliances installed in the United States of America or Canada (the "Appliance"). Dealers and employees of HHT have no authority to make any warranty or authorize any remedies in addition to or inconsistent with the terms of this warranty.
E. Contact Information Hearth & Home Technologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 www.fireplaces.com Please contact your Hearth & Home Technologies dealer with any questions or concerns. For the number of your nearest Hearth & Home Technologies dealer, please call 1-888-427-3973 (Bravo) or 1-800-927-6841 (Aztec).
