Owner's manual

ManualsBrandsHearth and Home Technologies ManualsFaxesFAN KIT GFK21B

Hearth & Home Technologies • GFK21B Fan Kit • 4016-096 Rev H • 05/08

Models:

GFK21B

Fan Kit

Installation

Instructions

Note: An arrow (¨) found in the text signiﬁ es change in

content.

Sharp Edges

• Wear protective gloves and safety

glasses during installation.

CAUTION

Note: This appliance must be electrically wired and grounded

in accordance with local codes or, in the absence of local

codes, with National Electric Code ANSI/NFPA 70 -latest

edition or the Canadian Electric Code CSA C22.1.

Shock Risk

Explosion Risk

Do NOT wire 110-120 VAC to gas control

valve.

Do NOT wire 110120 VAC to wall switch

• Incorrect wiring will damage millivolt

values.

• Incorrect wiring will override IPI safety

lockout and may cause explosion.

WARNING

If you need clariﬁ cation of any of the instructions contained here contact your dealer or the Technical Services Department

at 1-800-927-6841.

The Fan Kit has been designed to circulate room air through the appliance to enhance heat output. The fan kit operates on

120VAC, 60 Hz power. This is available through a receptacle in the factory installed junction box. The junction box is located

in the controls compartment of the appliance.

A control module is provided with the fan kit which automatically turns the fan on and off at preset times and is equipped

with a variable speed control to provide a quiet forced air ﬂ ow at the desired speeds.

Check Contents of Shipping Carton

Compare contents of carton in Table 1 with the actual parts received. If any parts are missing or damaged, contact your

dealer before starting installation. Do not install a damaged fan kit.

Installation Precautions

The Fan Kit is tested and safe when installed in accordance with this installation manual. It is your responsibility to read

all instructions before starting installation and to follow these instructions carefully during installation to assure maximum

beneﬁ t from, and safe operation of the fan.

Table 1 Contents of Carton

Fan 1

Screws 6

Foam Tape 2

Control Module 1

Electrical Cord 1

Magnetic Tape 2

Fan Bracket 1

Jumper Wire (blue) 1

Shock Risk

Fire Risk

Use ONLY optional accessories approved

for this appliance.

• Using non-listed accessories voids

warranty.

• Using non-listed accessories may result

in a safety hazard.

• Only Hearth & Home Technologies

approved accessories may be used

safely.

WARNING

Note: You may not need all parts included with this kit.

Summary of content (4 pages)

PAGE 1
Installation Instructions TM Models: GFK21B Fan Kit If you need clarification of any of the instructions contained here contact your dealer or the Technical Services Department at 1-800-927-6841. The Fan Kit has been designed to circulate room air through the appliance to enhance heat output. The fan kit operates on 120VAC, 60 Hz power. This is available through a receptacle in the factory installed junction box. The junction box is located in the controls compartment of the appliance.
PAGE 2
1. Install the Fan Bracket & Shield • • Place the fan bracket around the fan. See Figure 1. Figure 1 Fan Bracket-No screws If no fan shield is needed, install screws to hold the front of the fan bracket in place. See Figure 4. Figure 4 Fan Bracket Figure 5 Foam Tape ¨ • Use pliers to crimp the bracket tabs around the fan housing. See Figure 2.
PAGE 3
2. Remove Valve Assembly On a Novus 30 in. appliance (GNDC30 or GNBC30 only) the valve assembly must be raised slightly to allow the fan to be moved past it to the back of the appliance. FIREBOX BOTTOM 3. Install the Fan FAN APPLIANCE BACK Position the fan all the way to the rear and center in the appliance. Press the fan (magnets to the bottom) to the back of the appliance. See Figure 7. Plug the fan cord into the fan receptacle labeled “FAN” on the junction box. See Figure 8. 4.
PAGE 4
Dexen Valve (IPI) - Connect the black, white and red wires with 1/4 in. female connectors from fan control module to appliance junction box as shown in Figure 10. - Connect the black ground wire to the appliance. - Remove the green ignition control wire from the valve. - Connect the black with white stripe wire with 3/16 in. piggyback connector from fan control module to valve. - Connect green ignition control wire to piggyback connector on black with white stripe fan control module wire.