6911-N STOP! Call Us First! DO NOT RETURN TO STORE. For immediate help with assembly or product information call our toll free number: 1-800-577-9663 or email: customerservice@heartlandind.
(This page intentionally left blank.
ASSEMBLY MANUAL 16911-N 06-19-2020 A Backyard Products Company ROCKPORT 8' x 12' (244 x 366 cm) ACTUAL FLOOR SIZE IS 96 x 141" (243,2 x 358,1 cm) KEEP THIS MANUAL FOR FUTURE REFERENCE IMPORTANT! READ INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING ASSEMBLY. BEFORE YOU BEGIN • BUILDING RESTRICTIONS AND APPROVALS Be sure to check local building department and homeowners association for specific restrictions and/ or requirements before building.
TOOLS Required ❑ Phillips Optional ❑ Tool Belt/ ❑ Utility Knife Screwdriver Nail Pouch ❑ Shingle Blades ❑ Drill / Driver ❑ 1/8" Drill Bit ❑ 1/4" Drill Bit ❑ 5/16" Drill Bit ❑ 1/2" Drill Bit ❑ #2 Philips Drive Bit ❑ Tin Snips ❑ Caulk Gun (for drip edge) ❑ Chalk Line ❑ Paint Tools ❑ Hammer ❑ Nail Gun ❑ Pencil ❑ Ladder ❑ Tape Measure ❑ Square • gun nails ❑ Safety Glasses ❑ Level ❑ Gloves or Safety! Always use approved safety glasses during assembly.
ADDITIONAL MATERIALS FOUNDATION OR FLOOR MATERIALS • This shed does not include any floor or leveling materials. • See the FLOOR LEVELING section on page 7 for recommended methods and suggested materials to properly level your floor, as this will vary depending on your specific site. WOOD FLOOR FRAME MATERIAL REQUIRED: x10 x2 Use only wood treated for ground contact and fasteners approved for use with treated wood. Hot Dipped Galvanized Box-Type Nails.
Part identification letters are stamped on some parts. RS PARTS IDENTIFICATION AND SIZES WOOD SIZE CONVERSION CHART Treated lumber is stamped: Nominal Board Size Actual Size 2 x 4..............1-1/2" x 3-1/2" (3,8 x 8,9 cm) 1 x 4................ 3/4" x 3-1/2" (1,9 x 8,9 cm) 2 x 3..............1-1/2" x 2-1/2" (3,8 x 6,3 cm) 1 x 3................ 3/4" x 2-1/2" (3,8 x 6,3 cm) RS Check these locations for part stamp. PARTS LIST WALLS INVENTORY YOUR PARTS before you begin.
OVERHANG & TRIM PARTS LIST continued...
WALL PANELS & DOORS x2 x4 3/8 x 20 x 72" (1 x 50,8 x 182,9 cm) x4 3/8 x 48 x 72" (1 x 121,9 x 182,9 cm) 3/8 x 46-1/8 x 72" (1 x 117,2 x 182,9 cm) x1 x1 x1 x1 x1 x1 LEFT DOOR RIGHT DOOR NAIL BOXES x3 BOXES x5 BOXES 3" (7,6 cm) 2" (5,1 cm) FASTENER/HARDWARE BAG x120 1-1/2" (3,8 cm) x160 x115 3" (7,6 cm) x25 2" (5,0 cm) x95 1-1/4" (3,2 cm) 3/4" (1,9 cm) x75 x12 NOTE: If you are using a nail gun, nails may be used where screws are shown for quicker assembly.
FLOOR LEVELING OPTIONS There are multiple ways to level your floor frame. Our recommended leveling method is shown below. Leveling materials are not included in this kit. PREFERRED METHOD - 4x4 TREATED RUNNERS • 3" Screws angled into 4x4. • (2) at each point frame • and 4x4 touch. 12" (30,5 cm) O R Measurements to centers of 4x4's. D O MATERIAL REQUIRED 12" (30,5 cm) x2 4 x 4 x 12' (10 x 10 x 366 cm) Treated Lumber Fasteners for Frame to 4 x 4. (3" Screws shown as one option.
CONCRETE FOUNDATION Your kit contains all materials to construct a wooden floor. If you choose to install your kit on a concrete slab refer to the diagram below. Treated Sill Plate Caulk between sill plate and concrete. C 3-1/2" (8,9 cm) B A OR DO 4" (10,2 cm) Building Size Actual Size 8' x 12' (243,2 x 365,8 cm) 96" x 141" (243,2 x 358,1 cm) A B 96" (243,2 cm) 134" (340,4 cm) Requires: x2 2 x 4 x 11'-2" (5,1 x 10,2 x 344,5 cm) x2 2 x 4 x 8' (5,1 x 10,2 x 244 cm) MUST be treated lumber.
FLOOR FRAME PARTS REQUIRED: x10 x2 Look for TREATED 2 x 4 x 93" (5,1 x 10,2 x 236,2 cm) x40 3" (7,6 cm) Stamp 2 x 4 x 141" (5,1 x 10,2 x 358,1 cm) BEGIN 1 Orient parts as shown on flat surface. Measure and mark. Use (2) 3" nails at each mark. HINT: For easier nailing stand on frame.
LEVEL AND SQUARE FLOOR FRAME Before attaching floor decking, it is important to level and square the floor frame. A level and square floor frame is required to correctly construct your shed. BEGIN 1 See page 7 for the preferred floor leveling method. 2 Use level and check the frame is level before applying floor panels. 3 Check for frame squareness by measuring diagonally across corners. If the measurements are the same, the frame is square.
FLOOR PANELS PARTS REQUIRED: x62 2" (5,1 cm) 5/8 x 48 x 96" (1,6 x 121,9 x 243,8 cm) x1 Ensure your floor frame is square by installing one panel and squaring frame. BEGIN 1 Attach the 48" x 96" panel with the rough side up (painted-grid lines side) with the 48" edge and corner flush to the floor frame (Fig A). Secure panel with (2) 2" nails in the corners. 2 Move to the opposite side.
FLOOR PANELS PARTS REQUIRED: x1 x124 2" (5,1 cm) x1 5/8 x 48 x 96" (1,6 x 121,9 x 243,2 cm) 4 5/8 x 45 x 96" (1,6 x 114,3 x 243,2 cm) Continue installing panels with rough side up (painted grid lines). install 45" panel in middle of floor frame. Use grid lines on panels for 2" nails 6" apart on edges and 12" apart inside panels.
IMPORTANT! DO OR Check the floor frame is level after installing floor panels. Re-level if needed. • The floor should be used as a stable work surface for wall construction. HINT: • Organize your assembly procedure during the build process to avoid over-handling of the walls.
SIDE WALL FRAME PARTS REQUIRED: x2 OP x7 UM x2 UN x32 3" (7,6 cm) 2 x 4 x 46-1/2" (5,1 x 10,2 x 118,1 cm) 2 x 4 x 68" (5,1 x 10,2 x 172,7 cm) 2 x 4 x 94-1/2" (5,1 x 10,2 x 240 cm) BEGIN HINT: For easier nailing stand on frame. 1 Orient parts on edge on floor. Measure and mark.
SIDE WALL PANELS PARTS REQUIRED: x1 x45 2" (5,1 cm) 3/4" GAUGE BLOCK 46-1/8 x 72" (117,2 x 213,4 cm) Ensure your wall frame is square by installing one panel and squaring frame. 3 Place 46-1/8" x 72" panel onto wall frame flush to top of frame with primed side up as shown. Use the gauge block to mark the 3/4" measurement on the wall stud. Secure panel with (2) 2" nails in the corners (Fig. A). 4 Move to the opposite end.
SIDE WALL PANELS PARTS REQUIRED: x1 5 48 x 72" (121,9 x 213,4 cm) x90 x1 2" (5,1 cm) 3/4" GAUGE BLOCK 46-1/8 x 72" (117,2 x 213,4 cm) Place center 48" x 72" panel on frame as shown with primed side facing up. Secure with 2" nails 6" apart on edges and 12" apart inside panel. Flush Approx. 3/8" Reveal For squareness maintain flush and 3/4" measurement along panel edges.
BACK WALL FRAME PARTS REQUIRED: x3 x2 x12 3" (7,6 cm) UM 2 x 4 x 68" (5,1 x 10,2 x 172,7 cm) SZ 2 x 4 x 89" (5,1 x 10,2 x 226,1 cm) BEGIN 1 Orient parts on edge on floor. Measure and mark. Secure with (2) 3" nails at each mark.
BACK WALL PANELS PARTS REQUIRED: x2 x68 2" (5,1 cm) 3/4" GAUGE BLOCK 3/8 x 48 x 72" (1 x 121,9 x 182,9 cm) 2 Install 48" x 72" wall panels with primed side up as shown. Secure panels to frame with 2" nails 6" apart along edges and 12" apart on inside of panel. 3-1/2" (8,9 cm) Flush For squareness maintain flush and 3/4" measurement along panel edges.
FRONT WALL PARTS REQUIRED: x2 x2 x1 x8 RD 3" (7,6 cm) 2 x 4 x 16-1/2" (5,1 x 10,2 x 41,9 cm) UM 2 x 4 x 68" (5,1 x 10,2 x 172,7 cm) SZ 2 x 4 x 89" (5 x 10,2 x 226,1 cm) BEGIN 1 Orient parts on edge on floor. Measure and mark. 2 Use (2) 3" nails at each mark. HINT: For easier nailing stand on frame.
FRONT WALL PARTS REQUIRED: x1 x2 3" (7,6 cm) OO x38 1-1/4 x 2-1/2 x 69" (3,2 x 6,3 x 175,3 cm) TEMPORARY SUPPORT 2" (5,1 cm) x2 3/8 x 20 x 72" (1 x 50,8 x 182,9 cm) 3 Place 20" x 72" panels onto wall frame flush to SZ with primed side up as shown. Secure panel with 2" nails 6" apart. 4 Install OO as a brace to maintain 56" (142,3 cm) opening. Use (2) 3" screws to attach. 20" (50,8 cm) Flush For squareness maintain flush along panel edges.
FRONT WALL PARTS REQUIRED: x1 5 x5 3" (7,6 cm) OY 2 x 3 x 72" (5,1 x 7,6 x 213,4 cm) Center OY on SZ flush to edge of panel (Fig. A, B). Secure with (5) 3" screws spaced evenly and screwed-in at an angle. Fig. A OY Fig. B 3" (7,6 cm) Screws at angle Flush to panel edge Front wall panel OY Front wall panel CENTER CENTER FINISH Your front wall is now assembled.
RIGHT SIDE WALL INSTALLATION PARTS REQUIRED: x1 x12 OO 1-1/4 x 2-1/2 x 69" (3,2 x 6,3 x 175,3 cm) 3" (7,6 cm) x2 x27 3" (7,6 cm) 2" (5,1 cm) BEGIN 1 Center 12' right side wall on the 141" (358,1 cm) floor dimension. 1" (2,5 cm) overlap is to the bottom. Use OO as a temporary brace. Secure with (2) 3" screws. 1" ) 14 ,1 cm 8 (35 3" (7,6 cm) Screws D O O R OO 1" (2,5 cm) 2 First, nail lower edge of panel to floor frame with 2" nails 6" apart. Angle nail to hit floor frame (Fig. A).
BACK WALL INSTALLATION PARTS REQUIRED x18 x1 x2 3" (7,6 cm) 2" (5,1 cm) x11 1-1/2" (3,8 cm) x8 3" (7,6 cm) Fig. B BEGIN 1 2" (5,1 cm) Place back wall centered on floor. Secure wall with (1) 2" screw into side wall bottom plate (Fig. A) and top plate (Fig. B). 2" (5,1 cm) Screw Flush Secure wall to bottom plate first. ENSURE PANEL CORNERS ARE FLUSH. 2" (5,1 cm) Screw Fig. A 2 Nail lower edge of panels to floor with 2" nails 6" apart. Angle nail to hit floor frame (Fig. C).
LEFT SIDE WALL INSTALLATION PARTS REQUIRED: x2 2" (5,1 cm) BEGIN 1 Center left side wall on the 141" (358,1 cm) floor dimension. (35 141 8,1 " cm ) 2 Secure wall with (1) 2" screw through back wall panel into side wall bottom and top plates (Fig. B, Fig. A). 2" (5,1 cm) Screw Fig. B Secure wall to bottom plate first. ENSURE PANEL CORNERS ARE FLUSH. Flush Fig.
LEFT SIDE WALL INSTALLATION PARTS REQUIRED: x27 x1 2" (5,1 cm) x11 3 x12 1-1/2" (3,8 cm) 3" (7,6 cm) 3" (7,6 cm) Nail lower edge of side wall panels to floor frame with 2" nails 6" apart. Angle nail to hit floor frame (Fig. C). 3" (7,6 cm) Nails Secure wall bottom plates to floor with 3" nails (Fig. C). 6" (15,2 cm) Nail 2" nails first. 3" (7,6 cm) Nails 2" (5,1 cm) Nails Fig. C 3" (7,6 cm) Screw 4 Nail back wall panel to side wall stud with 1-1/2" nails 6" apart.
FRONT WALL INSTALLATION PARTS REQUIRED x10 2" (5,1 cm) x22 1-1/2" (3,8 cm) x2 x4 2" (5,1 cm) 3" (7,6 cm) Fig. B BEGIN 1 x4 3" (7,6 cm) 2" (5,1 cm) Screw Place front wall on floor centered between side walls. Secure wall with 2" screws into top and bottom plates (Fig. A, Fig. B). Flush Secure wall to bottom plate first. ENSURE PANEL CORNERS ARE FLUSH. Flush 2" (5,1 cm) Screw 2 Nail lower edge of panels to floor with 2" nails 6" apart. Angle nail to hit floor frame (Fig. C).
RAFTERS PARTS REQUIRED: x2 x11 x12 x132 3" (7,6 cm) OSB OR WOOD GRAIN 2" (5,1 cm) TEMPORARY SUPPORT 7-1/4 x 18-1/4" (18,4 x 46,4 cm) 2 x 6 x 5-1/4" x2 AYB (5,1 x 15,2 x 13,3 cm) PGA 2 x 4 x 68-7/16" (5,1 x 10,2 x 173,2 cm) You will build SIX assemblies. (5) with two gussets, and (1) with one gusset. ¸1 BEGIN 2 HINT: Place AYB against back wall at measurement shown. Secure AYB with (2) 3" screws as shown.
RAFTER INSTALL PARTS REQUIRED: x5 x24 x1 Preassembled ¸1 3" (7,6 cm) (1) GUSSET Preassembled BEGIN Secure rafters to top plate with (2) 3" screws in each rafter (Fig. A, Fig. B). . Note single-gusset rafter at back wall with gusset facing inward.
BACK GABLE UNIT PARTS REQUIRED: x10 x1 RLB 1-1/2" (3,8 cm) 2 x 4 x 35-3/16" (5,1 x 10,2 x 89,4 cm) x1 x1 BEGIN 1 Orient RLB on flat as shown. Place left gable panel as shown. Secure with 1-1/2" nails as shown. 1-3/4" (4,5 cm) 1-1/2" (3,8 cm) Nails Primed side up RLB (on flat) 1-1/2" (3,8 cm) 2 Place right gable panel flush to left panel. Secure with 1-1/2" nails as shown. 1-1/2" (3,8 cm) Nails Primed side up Flush FINISH Your back gable unit is now assembled.
BACK GABLE UNIT INSTALLATION PARTS REQUIRED: x40 x2 1-1/2" (3,8 cm) 3" (7,6 cm) Back Gable Unit BEGIN 1 Install back gable unit on back wall top plate. Measure 1-1/2" down from top plate and mark at each side as shown. Set gable unit on top plate. Hold secure with (1) 1-1/2" nail on each side. BE SURE GABLE IS CENTERED ON WALL BEFORE NAILING. 2 Continue nailing lower edge of panels into top plate with 1-1/2" nails 6" apart. 3 Secure panels to rafter with 1-1/2" nails 6" apart.
FRONT GABLE UNIT PARTS REQUIRED: x1 UY 1-1/2" (3,8 cm) 2 x 4 x 21-3/4" (5,1 x 10,2 x 55,2 cm) 2 x 4 x 6-1/2" (5,1 x 10,2 x 16,5 cm) x1 x12 x1 RH x1 BEGIN 1 Orient parts UY and RH on flat as shown. Place left gable panel as shown. Secure with 1-1/2" nails as shown. 1-3/4" (4,5 cm) 1-1/2" (3,8 cm) Nails Primed side up RH (on flat) Flush UY (on flat) 1-1/2" (3,8 cm) 2 Place right gable panel flush to left panel. Secure with 1-1/2" nails as shown.
FRONT GABLE LADDERS PARTS REQUIRED: x4 x24 SXA 3" (7,6 cm) 2 x 3 x 68-7/16" (5,1 x 7,6 x 173,8 cm) x6 URB 2 x 3 x 5-1/2" (5,1 x 7,6 x 14 cm) BEGIN 1 Arrange, measure and mark locations of four URB as shown place SXA on top. Secure with 3" screws as shown (Fig. A). Ensure parts are flush along edges. Fig.
FRONT GABLE UNIT PARTS REQUIRED: x2 Ladder Assemblies x4 x16 Front Gable Unit 3" (7,6 cm) 1-5/8" (4,1 cm) BEGIN 1 Place ladder assemblies in rafter jig, flush into corner and flush to AYB. Toe-screw ladder assemblies together with (4) 3" screws (Fig. F). Fig. F AYB Flush HINT: Pre drill to avoid splitting wood. 3" (7,6 cm) Screws 2 Flush at peak Place gable unit primed side down on gable ladders. Ensure panels are flush at peak of ladder and flush along top edge of ladder assembly.
FRONT GABLE UNIT INSTALLATION PARTS REQUIRED: x18 x2 2" (5,1 cm) 3" (7,6 cm) Front Gable Unit BEGIN 1 Install front gable unit on front wall top plate. Measure 1-1/2" (3,8 cm) down from top plate and mark at each side as shown. Set gable unit on top plate. Hold secure with (1) 2" nail on each side. BE SURE GABLE IS CENTERED ON WALL BEFORE NAILING. Continue nailing lower edge of panels into top plate with 2" nails 6" apart.
FRONT GABLE L-blocks PARTS REQUIRED: x8 3" (7,6 cm) x2 LUA 2 x 6 x 3-5/8" (5,1 x 15,2 x 9,2 cm) x2 AYB 2 x 6 x 5-1/4" (5,1 x 15,2 x 13,3 cm) BEGIN 1 Build two L-blocks by attaching AYB to LUA with (2) 3" screws (Fig. A). Fig. A 3" (7,6 cm) Screws 5-1/2" (14 cm) AYB HINT: Pre drill to avoid splitting wood. 3-5/8" (9,2 cm) LUA Ensure each L-block is in the correct position using a level, as shown in Fig. B. Pre-drill all holes. Secure each L-block with (4) 3" screws, as shown (Fig. C). 2 Fig.
FRONT OVERHANG SOFFIT PARTS REQUIRED: x20 x2 1-1/4" (3,2 cm) 3/8 x 8-1/2 x 61-5/16" (1 x 21,6 x 155,7 cm) Ensure overhang boards meet at peak (Fig. A). BEGIN 1 Position 61-5/16" overhang boards flush at peak, primed side down and flush to wall panels (Fig A). Secure panels to frame with (20) 1-1/4" screws spaced evenly. 61-5/16" Fig.
SOFFIT NAILERS PARTS REQUIRED: x2 x2 5/8" x 1-1/2" x 46-3/4" (1,6 x 3,8 x 118,7 cm) OSB x2 x16 3/8" x 2" x 5" (1 x 5,1 x 12,7 cm) x4 5/8" x 1-1/2" x 96" (1,6 x 3,8 x 243,2 cm) OSB 2" (5,1 cm) 1-1/4" (3,2 cm) BEGIN 1 At the back of the shed, install 2" x 5" soffit filler flush to bottom and outside edges of rafter (Fig. A). Fasten with (2) 1-1/4" screws as shown. Repeat on opposite side. 2 Mark wall at each rafter with a square flush to bottom side of rafter and side wall (Fig. B).
EAVE SOFFIT PARTS REQUIRED: x48 x2 1-1/4" (3,2 cm) 3/8 x 5-3/16 x 71-1/4" (1 x 13,2 x 181 cm) x2 3/8 x 5-3/16 x 79-3/4" (1 x 13,2 x 202,6 cm) BEGIN 1 Place 79-3/4" and 71-1/4" soffit boards primed side down on bottom side of rafter and nailer. Flush soffit board to front corner of overhang L-block (Fig. A), side wall panels and nailer (Fig. B). Secure with 1-1/4" screws 12" apart and angled into rafter at seam (Fig. B, Fig. C). Repeat steps on opposite side.
ROOF PANELS PARTS REQUIRED: x2 7/16 x 21 x 96" (1,1 x 53,3 x 243,2 cm) x4 7/16 x 21 x 23-1/4" (1,1 x 53,3 x 59,1 cm) x2 2" (5,1 cm) 7/16 x 21 x 31-3/4" (1,1 x 53.3 x 80,6 cm) x2 3/4" GAUGE BLOCK x2 7/16 x 48 x 23-1/4" (1,1 x 121,9 x 59,1 cm) x2 7/16 x 31-3/4 x 48" (1,1 x 80,6 x 121,9 cm) x2 7/16 x 48 x 96" (1,1 x 121,9 x 243,2 cm) Roof panels may cause serious injury until securely fastened. Install all roof panels with the rough side facing up (painted grid lines side).
ROOF PANELS PARTS REQUIRED: 3 Keep spacing between the center of the rafters. x216 Fig. C 24" (61 cm) 24" (61 cm) 2" (5,1 cm) 24" (61 cm) 24" (61 cm) Secure with (1) 2" nail into each rafter (Fig. C). 2" Nails Flush at peak 4 Install 48"x 23-1/4" and 21"x 31-3/4" roof panels flush to installed panel and flush at rafter peak (Fig. B, Fig. D). Fig. B 48"x 23-1/4" Fig. D Flush Secure with (2) 2" nails into each panel as shown. Flush 21"x 31-3/4" Flush OR DO 5 Fig.
ROOF PANELS PARTS REQUIRED: 6 Install roof panels flush to installed panels and flush to each edge, as shown. Install panels in the following order: 1. 31-3/4"x 48" 2. 21"x 96" 3. 21"x 23-1/4" Secure roof panels with 2" nails 6" apart along edges and 12" inside panels. 6" (15,2 cm) Flush 12" (30,5 cm) Flush Flush 21" x 23-1/4" Flush OR 21" x 96" DO 31-3/4" x 48" 7 Repeat process to attach roof panels on the opposite side. OR DO FINISH Your roof panels are now installed.
GABLE FASCIA - FRONT PARTS REQUIRED: x4 x2 x22 TEMPORARY GI 19/32 x 3 x 23" (1,5 x 7,6 x 58,4 cm) PDB 19/32 x 3-1/2 x 66-1/4" (2,5 x 8,9 x 168,3 cm) x1 19/32 x 5-1/2 x 6-13/16" (1,5 x 14 x 17,3 cm) LEFT x1 19/32 x 5-1/2 x 6-13/16" (1,5 x 14 x 17,3 cm) RIGHT 2" (5,1 cm) Use GI as temporary ledger-boards to help install trim boards. BEGIN Install (4) GI projecting out past edge of OSB roof panels, two on each side of roof, as shown. Fasten each with 2" finish nails. Do not sink nails completely.
FRONT OVERHANG TRIM PARTS REQUIRED: x2 x8 3/8 x 4-3/8 x 8-1/2" (1,0 x 11,1 x 21,6 cm) 1-1/4" (3,2 cm) BEGIN 1 Install overhang corner soffit trim boards primed side out as shown (Fig. A). Secure parts with 1-1/4" screws. Fig. A 1-1/4" (3,2 cm) Screws Flush Flush 4-3/8 x 8-1/2" Primed side out 4-3/8 x 8-1/2" Primed side out FINISH Your corner soffit trim is now installed.
EAVE FASCIA PARTS REQUIRED: x2 x2 ¸1 x36 2" (5,1 cm) 3/8 x 3-1/4 x 71-1/4" (1 x 8,3 x 181 cm) 3/8 x 3-1/4 x 79-3/4" (1 x 8,3 x 202,6 cm) BEGIN Install eave fascia boards flush to rafters and flush to roof panels (Fig. A). Secure with (2) 2" finish nails at each rafter and (4) 2" finish nails at seam. Repeat STEP 1 to install fascia on opposite side. 3/8 x 3-1/4 x 71-1/4" 3/8 x 3-1/4 x 79-3/4" SEAM 3/8 x 3-1/4 x 71-1/4" 3/8 x 3-1/4 x 79-3/4" Fig.
GABLE FASCIA - REAR PARTS REQUIRED: x4 x2 x22 TEMPORARY GI x1 19/32 x 5-1/2 x 6-13/16" (1,5 x 14 x 17,3 cm) LEFT x1 19/32 x 5-1/2 x 6-13/16" (1,5 x 14 x 17,3 cm) RIGHT 19/32 x 3 x 23" (1,5 x 7,6 x 58,4 cm) PDB 19/32 x 3-1/2 x 66-1/4" (2,5 x 8,9 x 168,3 cm) 2" (5,1 cm) Use GI as temporary ledger-boards to help install trim boards. BEGIN Install (4) GI projecting out past edge of OSB roof panels, two on each side of roof, as shown. Fasten each with 2" finish nails. Do not sink nails completely.
COLLAR TIES PARTS REQUIRED: x2 x12 3" (7,6 cm) OP 2 x 4 x 46-1/2" (5,1 x 10,2 x 118,1 cm) BEGIN 1 Position and level OP on 3rd and 5th rafters from back wall. Flush OP to roof panels. HINT: For best appearance install OP on rafter facing away from door. 2 Secure with 3" nails as shown. OP Flush Flush 3" (7,6 cm) Nails 5th 3" (7,6 cm) Nails 3rd FINISH Your collar ties are now installed.
DOORS PARTS REQUIRED: x1 x4 3" (7,6 cm) OO x2 1-1/4 x 2-1/2 x 69" (3,2 x 6,3 x 175,3 cm) 1-1/4" (3,2 cm) x1 GAA 1 x 3 x 5" (2,5 x 7,6 x 12,7 cm) x1 Left Door x1 Right Door BEGIN 1 Orient parts as shown on flat surface. 3/8" offset is to top. Look for red (right) and green (left) on hinge board. Attach temporary supports OO and GAA as shown. Tighten securely.
DOORS PARTS REQUIRED: x1 2 x12 3" (7,6 cm) OO 1-1/4 x 2-1/2 x 69" (3,2 x 6,3 x 175,3 cm) Install OO flush under panels. Secure to floor frame with (2) 3" screws (Fig. A). Fig. A Flush against wall panels OO OO 3 Center doors on panel seam as shown (Fig. B). 4 Screw hinge boards into wall supports and floor with (10) 3" screws as shown. Make sure screws go into framing and floor (Fig. C). Remove temporary supports and ensure that the doors open properly. SEAM Fig.
DOOR TRIM x5 PARTS REQUIRED: x1 x4 WR 19/32 x 2-1/2" x 63" (1,5 x 6,4 x 160 cm) x56 x1 FA 19/32 x 2-1/2" x 22-5/8" (1,5 x 6,4 x 57,5 cm) 2" (5,1 cm) 3/4" (1,9 cm) 56" Metal Threshold 3/4" (1,9 cm) x11 Bagged seperately / special coating BEGIN 1 Reinforce the door and install horizontal door rails FA. Secure trim with 3/4" screws from behind door panel into trim (Fig. A, B). 2 Center trim WR over doors and secure with (5) 2" finish nails.
DOOR STIFFENERS PARTS REQUIRED: x2 x14 2" (5,1 cm) OO 1-1/4 x 2-1/2 x 69" (3,2 x 6,3 x 175,3 cm) BEGIN 1 Center OO’s vertically on the left and right doors as shown (Fig. A, Fig. B). Secure using (7) 2" screws through outside trim into OO (Fig. B). OO x2 Center OO in door opening. Fig. B IT IS IMPORTANT TO HOLD THESE DIMENSIONS Fig. A 3/4" (1,9 cm) 3/4" (1,9 cm) OFFSET 2" (5,1 cm) Screws x14 11" (27,9 cm) Approximately FINISH Your door stiffeners are now installed.
DOOR HARDWARE PARTS REQUIRED: x8 x2 1" (2,5 cm) 5/16" (0,8 cm) Drill Bit BEGIN Place spring bolt onto OO in open position with bolt end 3/8" down from frame. Bolt is open when loop is contacting base (Fig A). 1 Mark and pre-drill holes for screws. 2 Install bolt with screws supplied and drill 5/16" hole for bolt to extend into. 3 Place bolt onto OO in open position with bolt end 1/2" up from floor. Bolt is open when loop is contacting base (Fig B). Mark and pre-drill holes for screws.
DOOR HARDWARE / DECORATIVE HINGES PARTS REQUIRED: x1 x2 x4 1-1/2" (3,8 cm) 3/8" (10,9 cm) Drill Bit x12 3/4" (1,9 cm) 1/4" (0,6 cm) Drill Bit BEGIN 1 Measure and mark location of hole on outside of right door as shown (Fig. A). Pre-drill hole with 1/4" drill. Re-drill hole with 3/8 " drill. Keep drilled hole square to trim to avoid breaking edge of door stiffener. Flush to hinge RIGHT DOOR 1-3/4" (4,4 cm) TOP VIEW 35-3/4" (90 cm) 1-3/4" (4,4 cm) Fig.
GABLE PEAK PARTS REQUIRED: x1 x4 7-1/4 x 18-1/4" (18,4 x 46,4 cm) WITH WOOD GRAIN ON FACE BEGIN 1 Position gable peak flush to peak of overhang as shown. Secure using (4) 2" finish nails. Primed side out 2" (5,1 cm) Finish Nails FINISH Your front gable peak trim is installed.
GABLE WINDOW PARTS REQUIRED: x2 1-1/4" (3,2 cm) x1 BEGIN 1 Apply high quality exterior-grade caulk behind frame near edge before installing to seal window. 2 From outside of shed, position window in opening and level. Use (2) screws at top of windows. Do not fully tighten screws. 1-1/4" (3,2 cm) Screws Caulk behind frame near edge before installing. You must use a caulk sealant behind window flange in order to validate your warranty.
WINDOWS TRIM PARTS REQUIRED: x2 3 x2 x8 EY 2" (5,1 cm) 19/32 x 2-1/2 x 9" (1,5 x 6,4 x 22,9 cm) WA 19/32 x 2-1/2 x 36-3/4" (1,5 x 6,4 x 93,3 cm) Center WA 3/4" onto window frame. Secure using (2) 2" finish nails as shown. Do not nail into window flange. Flush Flush WA 3/4" (1,9 cm) Centered 4 Position EY on onto window frame as shown. Secure using (2) 2" finish nails. Remove 1-1/4" screws.
GABLE WINDOW PARTS REQUIRED: x12 3/4" (1,9 cm) 6 From inside, secure trim with (12) 3/4" screws. Snip protruding finish nails. Do not screw into window flange. 3/4" (1,9 cm) Screws INSIDE OF SHED 3/4" (1,9 cm) Screws Snip off 2" nails protruding through panel. FINISH Your window is now installed.
CORNER TRIM PARTS REQUIRED: x4 x4 x48 2" (5,1 cm) 3/8 x 1-3/4 x 70-1/2" (1 x 4,4 x 179,1 cm) 3/8 x 1-3/4 x 67-9/16" (1 x 4,4 x 171,6 cm) BEGIN 1 Front and back 70-1/2" corner trim is flush under gable panel and flush along the face of side wall panel. Fasten with 2" finish nails spaced evenly. 2 Install 67-9/16" side corner trim flush along edge of front corner trim and flush up against eave soffit. Fasten with 2" finish nails spaced evenly. Repeat STEPS 1 - 2 to install trim to all four corners.
HOOK & EYE PARTS REQUIRED: x2 Eye Hook BEGIN 1 Install hooks into endcap and into L-block behind (Fig. A). 2 Swing door open to locate eye. Fig. A Eye FINISH Your hook and eyes are installed.
VENTS PARTS REQUIRED: x12 1/2" (1,3 cm) 8 x 16" (20,3 x 35,6 cm) x2 ¸1 You can place your side wall vent on either side of shed BEGIN Locate and mark for vents in side walls. Install (1) vent near the floor and (1) vent near the eave. Caulk behind vent flanges. Secure with 1/2" screws.
PAINT & CAULK - NOT INCLUDED - • Use acrylic latex caulk that is paintable. Caulk at all horizontal and vertical seams, between the trim and walls, and all around the door trim. • Use a high quality exterior acrylic latex paint. When painting your building, there are a few key areas that can be easily overlooked that must be painted: • Bottom edge of all siding and trim • Inside of doors and all 4 edges Note: Prime all un-primed exterior wood before painting.
SHINGLES - NOT INCLUDED • Follow directions provided by manufacturer and these instructions. Familiarize yourself with a 3-Tab Shingle. Notch SHINGLE NAIL PATTERN 1" (2,5cm) 1/2" (1,3cm) Notch Sealing Str ip 1" (2,5cm) Half A Rain Slot Full Rain Slot NAILS NEVER DRIVE FASTENERS INTO OR ABOVE SEALING STRIPS. BEGIN 1 Install first starter row upside down and color up with a 1" overhang at back and bottom of roof panel. Use (4) nails per shingle.
SHINGLES continued... 2 2 Beginning at front of shed, install first row of shingles with notch at 1" past roof edge or flush with drip edge. Roof Deck FRONT OF SHED 1" (2,5 cm) Notch BACK OF SHED Flush with starter row. - or - Drip Edge Flush with starter row. Notch 3 Install second row of shingles flush at top of first row's rain slots. Ensure 1" overhang or flush to drip edge at front, stagger each row. FRONT OF SHED BACK OF SHED 1" (2,5 cm) Notch Flush with rain slots.
SHINGLES continued... 5 Continue installing rows of shingles to the peak. At the peak make sure there is a maximum of 5" or less to the rain slot, as shown below. If shingles overlap at ridge cut to peak with a utility knife. Cut Off. 5" (12,7 cm) MAX. CUT Top of rain slot. 5" (12,7 cm) or less. • If more than 5" to rain slot you must install another row of shingles. 6 Repeat steps 1 - 5 to shingle the opposite side of your roof. Trim shingles at ridge.
SHINGLES - RIDGE CAP • You will finish off the top of the roof with a ridge cap made from shingles. BEGIN 1 Cut shingles into THREE pieces. Hint: Use cut-off pieces first. 2" (5 cm) 2" (5 cm) 2" (5 cm) 2" (5 cm 2" (5 cm) 2" (5 cm) Score shingle, then snap-off angled cut. Weather Seal Top of slot. Note: • You will need about 30 - 32 cut pieces. 2 30 to 32 Pieces Install first ridge cap flush to shingles at front, as shown. (1) Nail per side through weather seal.
SHINGLES - RIDGE CAP continued... 4 Continue installing ridge cap to back of roof. 5 Make sure there is 4" between the shingle-color and edge of shingles. 4" (10 cm) 6 Trim cap off flush to shingles When you have 4" minimum of shingle color cut one piece to cap your roof. Cut at top of rain slot. Cap 7 Install flush to shingles. Flush to shingles (2) Nails per side. FINISH You have finished your ridge cap.
LIMITED CONDITIONAL WARRANTY* Backyard Storage Solutions, LLC warrants the following: 1. Every product is warranted from defects in workmanship and manufacturing for 1 year. 2. All accessories, hardware and metal components are warranted for 2 years. 3. All Oriented Strand Board (OSB) is warranted for 2 years 4. Siding and Trim is warranted for 15 years. 5. LP Prostruct® Flooring is warranted for 10 years 6. Cedar lumber is warranted for 15 years. 7. Preserved Pine is warranted for 10 years. 8.
