Installation instructions

P/N: 41014306-EN rev A
11/1/15

2
3
6
7
1
4
5
8













Location of these materials may vary depending on your model.
Plastic
Putty
Knife
Adjustable
Wrench
Socket
Wrench Set
OR
Phillips head
or
Quadrex
head
screwdriver
™
™
ToolsNecessary:
Pliers
Awl
(OR)
•
•
•
•
•
•
•
•
•
•
•
If possible, use a hand truck to position the refrigerator directly in front of its cabinet enclosure.
Plug in the power cord, and push the refrigerator straight back into place.
(if necessary)
refrigerator:
•
• The cabinet should be level at the front and rear.
• The sides should tilt ¼-inch (6 mm) from front-to-
back (to ensure that doors close and seal properly).
• Doors should align with each other and be level.
To level the cabinet using the front rollers:
1 Remove the toe grille (Figure 1).
2
3
/
8
inch socket
wrench to raise or lower the front rollers (Figure 2).
We use packing foam and tape to secure the internal parts of your refrigerator for shipping.
Once the refrigerator is in position, you can remove this material.

• Shifting the refrigerator from side
• Do not block the toe grille on the
lower front of your refrigerator.
for proper operation.

Raise the front of the refrigerator
enough so the doors close freely when
opened halfway. The refrigerator
should slope ¼ inch to ½ inch
from front-to-back. Then level the
refrigerator from side-to-side.
Vegetables Fruits
lo
hi
Humidity Control
Top
Hinge
Cover
Top
Hinge
Center
Hinge
Shim
Pin
temperature
coldest
cold
off
* recommended
garage
temperature
coldest
cold
off
* recommended
Figure 3
3 Lower the anti-tip bracket clockwise until it contacts the floor. (Figure 3).
Raise
Figure 2
garage
temperature
coldest
cold
off
* recommended
Anti-tip
Bracket
The anti-tip device
must be installed
according to the
instructions in your
Use & Care Manual.
Failure to do so will result in
injury.
Installation Instructions for Top Mount Refrigerator
This document should only be removed by customer after installation.
WARNING
NOTE
CAUTION
CAUTION
NOTE
WARNING
CAUTION
Controls
Remove Internal Shipping Materials
Door Removal (if necessary)
Installation Checkoff List
Level Refrigerator & Adjust Doors
Place In Permanent Position
Transport Unpackaged Refrigerator To Site
Prepare The Installation Site
To avoid electric shock, which can cause death or severe personal injury, do not connect your
refrigerator to an electrical power source until you have completed Step 3 of these instructions.
These installation instructions
are provided only as a possible
customer option. We recommend
that you use a service or kitchen
contracting professional to install
your refrigerator.
Include these minimum guidelines in your site
: 1 inchRear
Sides & Top inch
Room temperatures below 55°F
(13°C) or above 110°F (43°C)
will impair cooling ability of your
refrigerator’s compressor
.
preparation:
Choose a place near a grounded electrical
outlet.
Do not use an extension cord or an adapter plug.
Avoid direct sunlight and close proximity to a
range, dishwasher or other heat source.
Floor should be level and able to support a fully
loaded refrigerator.
Allow the following clearances for ease of
installation, proper air circulation, and plumbing and
electrical connections:
8
/:
3
By now, you have already removed your refrigerator’s shipping carton.
You may still need to use a hand truck to move it through close spaces or
entrances. If the refrigerator is larger than an entrance, consider two options:
Remove the entrance door if one exists.
Remove the refrigerator doors (see how in your Use & Care Guide).
When using a hand truck:
Load refrigerator from side of cabinet only.
Do not run retaining straps over handles.
Do not over-tighten retaining straps.
Never use refrigerator handles to move the refrigerator.
Remove tape from doors only after unit is in place.
Shifting the refrigerator from side to
side may damage flooring.
Please contact the store from which you purchased your refrigerator.
Not satisfied with the installation of your refrigerator?
Handles are secure and tight
Door seals completely to cabinet on all sides
Freezer door is level across the top
Refrigerator is level, side to side and tilted
¼” (6mm) front to back
Toe grille is properly attached to refrigerator
Cabinet is setting solid on all corners
Doors
Leveling
Electrical Power
Final Ch
ecks
Shipping material removed
Fresh Food and Freezer controls set
Crisper Humidity controls set
Registration Card sent in
House power turned on
Refrigerator plugged in
If you need to remove the doors to get your refrigerator into the house, please see “Door
Removal Instructions” in your Use & Care Manual.
When changing controls, wait 24 hours before making additional adjustments.