Owner’s Manual Installation and Operation Model: Escape-36DV CAUTION DO NOT DISCARD THIS MANUAL • Important operating and maintenance instructions included. • Read, understand and follow these instructions for safe installation and operation. WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.
Read this manual before installing or operating this appliance. Please retain this owner’s manual for future reference. Congratulations Congratulations on selecting a Heat & Glo gas appliance —an elegant and clean alternative to wood burning appliances. The Heat & Glo gas appliance you have selected is designed to provide the utmost in safety, reliability, and efficiency. This Owner’s Manual should be retained for future reference.
Table of Contents 1 Listing and Code Approvals A. B. C. D. E. F. G. 9 Gas Information Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . BTU Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . Non-Combustible Materials Specification. . . . . . . . . . . . . . Combustible Materials Specification . . . . . . . . . . . . . . . . . Electrical Codes . . . . . . . . . . . . . . .
1 Listing and Code Approvals A. Appliance Certification C. High Altitude Installations MODELS: Escape-36DV, Escape-36DVLP LABORATORY: Underwriters Laboratories, Inc. (UL) TYPE: Direct Vent Gas Appliance Heater STANDARD: ANSI Z21.88-2000 • CSA2.33-M98 • UL307B This product is listed to ANSI standards for “Vented Gas Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and Recreational Vehicles”, and “Gas Fired Appliances for Use at High Altitudes”.
Note: The following requirements reference various Massachusetts and national codes not contained in this document. G.
2 Getting Started A. Design and Installation Considerations C. Inspect Appliance and Components Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required. WARNING Inspect appliance and components for damage. Damaged parts may impair safe operation. • Do NOT install damaged components. • Do NOT install incomplete components.
D. Inspect Firebox Surface cracking or crazing of firebrick material is normal and expected. The following types of cracks are acceptable and do not require replacement of the unit or the firebox: • Cracks that do not propagate entirely thru the material. • Light fracture lines or “spider-webbing” on the surface of the material. • Cracks that are less than 1/32 in. wide and less than 3 in. long. • If cosmetically unacceptable, such cracks may be repaired with the SRV-PACK service kit.
3 Framing and Clearances WARNING Note: • Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY. • Illustrations/diagrams are not drawn to scale. • Actual installation may vary due to individual design preference. Fire Risk Provide adequate clearance: • Around air openings • To combustibles • For service access Locate appliance away from traffic areas. A.
insulation. If the appliance is being installed on a cement slab, a layer of plywood may be placed underneath to prevent conducting cold up into the room. B. Constructing the Appliance Chase A chase is a vertical boxlike structure built to enclose the gas appliance and/or its vent system. Vertical vents that run on the outside of a building may be, but are not required to be, installed inside a chase. C. Clearances Construction of the chase may vary with the type of building.
D. Mantel Projections 3-1/2 IN. NO COMBUSTIBLES IN THIS AREA FINISH WALL COMBUSTIBLE COMBUSTIBLE FRAMING 7-1/2 IN. MINIMUM 36 IN. METAL PANELS (PROVIDED) UNLIMITED NON-COMBUSTIBLE MATERIAL COMBUSTIBLE PROJECTIONS 12 10-1/2 9 7-1/2 6 11-1/2 IN. 10 IN. MINIMUM 4-3/4 3-1/2 2-1/4 1 12 IN. Figure 3.4 Clearances to Mantel Legs or Wall Projections (Acceptable on both sides of opening.) 8 IN. 4 IN. MINIMUM NON-COMBUSTIBLE FACING MINIMUM 1/2 INCH THICKNESS TOP OF FIREPLACE OPENING WARNING Figure 3.
4 Termination Locations A. Vent Termination Minimum Clearances HORIZONTAL OVERHANG WARNING 2 FT. MIN. 20 INCHES MIN. VERTICAL WALL LOWEST DISCHARGE OPENING Fire Risk. Explosion Risk. Inspect external vent cap regularly. • Ensure no debris blocks cap. • Combustible materials blocking cap may ignite. • Restricted air flow affects burner operation. GAS DIRECT VENT TERMINATION CAP X 12 ROOF PITCH IS X/ 12 H (MIN.) - MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING WARNING Fire Risk.
M N P R Q (See Note 2) V T V S Electrical Service S V D* V V = VENT TERMINAL A B D* X = AIR SUPPLY INLET = 12 inches.................clearances above grade, veranda, (See Note 1) porch, deck or balcony = 12 inches.................clearances to window or door that may be opened, or to permanently closed window. (Glass) = 22 inches.................vertical clearance to unventilated soffit or to ventilated soffit located above the terminal *42 inches................
5 Vent Information and Diagrams A. Vent Table Key The abbreviations listed in this vent table key are used in the vent diagrams. V2 Second section of vertical length H1 First section (closest to appliance) of horizontal length H2 Second section of horizontal length Vertical . First section (closest to appliance) of vertical length in V1 8-1/2 in. WARNING Fire Hazard. Explosion Risk. Asphyxiation Risk.
D. Vent Diagrams WARNING Fire Risk. Explosion Risk. Do NOT pack insulation or other combustibles between ceiling firestops. • ALWAYS maintain specified clearances around venting and firestop systems. • Install wall shield and ceiling firestops as specified. Failure to keep insulation or other material away from vent pipe may cause fire. 1. Top Vent - Horizontal Termination V1 Minimum One Elbow Note: Must have a 12 inches minimum vertical vent before attaching any elbow to the unit. H1 Maximum 1 ft.
1. Top Vent - Horizontal Termination - (continued) V1 + V2 Minimum Three Elbows Note: Must have a 12 inches minimum vertical vent before attaching any elbow to the unit. H Maximum 1-1/2 ft. 457 mm 1-1/2 ft. 457 mm 2 ft. 610 mm 2 ft. 610 mm 2-1/2 ft. 762 mm 5 ft. 1524 3-1/2 ft. 1067 mm 8 ft. 2438 4-1/2 ft. 1372 mm 11 ft. 3353 V1 + V2 + H1 + H2 = 63 ft. (19.2 m) Maximum H1 + H2 = 23 ft. (7.1 m) Maximum H2 V2 H1 V1 Figure 5.5 Heat & Glo • Escape-36DV • 2012-900 • Rev.
2. Top Vent - Vertical Termination V1 = 40 ft. Max. (12.2 m) No Elbow Note: On vertical venting configurations install the flue restrictor (located behind the right side panel) per the following flue restrictor instructions. V1 Figure 5.6 Flue Restrictor Instructions 1. The flue restrictor (Figure 5.7) is located behind the right side panel. Use the restrictor if the vertical vent run is over 20 feet and has NO elbows. FLUE RESTRICTOR 2.
Two Elbows V1 + V2 Minimum H Maximum 1-1/2 ft. 457 mm 2 ft. 610 mm 2 ft. 610 mm 2-1/2 ft. 762 mm 2-1/2 ft. 762 mm 5-1/2 ft. 1676 mm 3-1/2 ft. 1067 mm 8-1/2 ft. 2591 mm 4-1/2 ft. 1372 mm 11-1/2 ft. 3505 mm V1 + H1 + V2 = 63 ft. (19.2 m) Maximum H1 + H2 = 23 ft. (7.1 m) Maximum Note: Must have a 12 inches minimum vertical vent before attaching any elbow to the unit. V2 H1 V1 Figure 5.9 Heat & Glo • Escape-36DV • 2012-900 • Rev.
2. Top Vent - Vertical Termination - (continued) V1 + V2 Minimum Three Elbows H1 + H2 Maximum 1-1/2 ft. 305 mm 2 ft. 610 mm 2 ft. 457 mm 2-1/2 ft. 762 mm 2-1/2 ft. 610 mm 5-1/2 ft. 1676 mm 3-1/2 ft. 914 mm 8-1/2 ft. 2591 mm 4-1/2 ft. 1219 mm 11-1/2 ft. 3505 mm V1+ V2 + H1+ H2= 63 ft. (19.2 m) Maximum H1 + H2 = 23 ft. (7.1 m) Maximum Note: Must have a 12 inches minimum vertical vent before attaching any elbow to the unit. V2 H1 H2 V1 INSTALLED HORIZONTALLY Figure 5.
6 Vent Clearances and Framing A. Pipe Clearances to Combustibles B. Wall Penetration Framing Combustible Wall Penetration WARNING Fire Risk. Explosion Risk. Maintain vent clearance to combustibles as specified. • Do not pack air space with insulation or other materials. Failure to keep insulation or other materials away from vent pipe may cause fire. 3 in. TOP CLEARANCE Frame a hole in a combustible wall for an interior wall shield firestop, (Figure 6.3) whenever a wall is penetrated.
C. Vertical Penetration Framing WARNING Fire Hazard Keep loose materials or blown insulation from touching the vent pipe. • National building codes recommend using attic shield to keep loose materials/ blown insulation from contacting vent. • Hearth & Home Technologies requires the use of an attic shield. ATTIC ABOVE 10 IN. (254 MM) Installing the Ceiling Firestop • Frame an opening 10 inches by 10 inches whenever the vent system penetrates a ceiling/floor (see Figure 6.4).
7 Appliance Preparation A. Removing Non-combustible Facing Material Assembly The non-combustible assembly is located on the right side of appliance. CAUTION Handle with care. • Non-combustible material may be damaged if dropped. • Hold non-combustible pieces in place. • Remove and save two screws from upper bracket. • Remove non-combustible pieces. • Remove and save three screws from lower bracket. • Discard brackets. • Replace screws in holes where brackets were attached to appliance. B.
NON-COMBUSTIBLE FACING MATERIAL (SUPPLIED ATTACHED TO BACK OF APPLIANCE) APPLY FASTENERS FROM FASTENER PACKET IN THESE AREAS Figure 7.2 Attaching Non-combustible Facing Material C. Installing Non-combustible Facing Material NON-COMBUSTIBLE ZONE WARNING Fire Risk. • Follow these instructions exactly. • Facing materials must be installed properly to prevent fire. • No materials may be substituted without authorization by Hearth & Home Technologies. 41 in.
8 Installing Vent Pipe A. Assembly of Vent Sections (DVP Pipe) WARNING Do not mix pipe, fittings or joining methods from different manufacturers. WARNING Fire Risk Exhaust Fumes Risk Impaired Performance of Appliance • Overlap pipe slip sections at least 1-1/2 inches. • Use pilot holes for screws. • Screws must not exceed one inch long. • Pipe may separate if not properly joined. Assembling Pipe Sections Insert the inner flue of section A into the flared inner flue of section B.
Note: Make sure that the seams are not aligned to prevent unintentional disconnection. This will secure the slip section to the desired length and prevent it from separating. The slip section can then be attached to the next pipe section. If the slip section is too long, the inner and outer flues of the slip section can be cut to the desired length. Cut from this end (outer) CORRECT Cut from this end (inner) Figure 8.5 Figure 8.
Securing the Vent Sections Vertical Sections Vertical sections of pipe must be supported every 8 feet after the 25 foot maximum unsupported rise. The vent support or plumber’s strap (spaced 120° apart) may be used to do this (see Figure 8.8). Horizontal Sections Horizontal sections of vent must be supported every 5 feet with a vent support or plumber’s strap. Figure 8.8 Securing Vertical Pipe Sections Figure 8.9 Securing Horizontal Pipe Sections B.
C. Installing Heat Shield and Horizontal Termination Cap WARNING Fire Hazard When installing a horizontal termination cap, follow the cap location guidelines as prescribed by current ANSI Z223.1 and CAN/CGA-B149 installation codes. Impaired performance of appliance WARNING • Telescoping flue section of termination cap MUST be used when connecting pipe section to termination cap. Burn Risk • Local codes may require installation of a cap shield to prevent anything or anyone from touching the hot cap.
Caulk the gap between the roof flashing and the outside diameter of the pipe. Also caulk the perimeter of flashing that contacts roof surface as shown in Figure 8.15. D. Installing Roof Flashing and Vertical Termination Cap To install roof flashing see Figure 8.13. For installation of vertical termination cap see minimum vent heights for various pitched roofs (see Figure 8.13). HORIZONTAL OVERHANG 2 FT. MIN. 20 INCHES MIN.
Assembling and Installing Storm Collar CAUTION Sharp Edges • Wear protective gloves and safety glasses during installation. Connect both halves of the storm collar with two screws (see Figure 8.16). Wrap the storm collar around the exposed pipe section and align brackets. Insert a bolt (provided) through the brackets and tighten nut to complete storm collar assembly (see Figure 8.17). Slide the assembled storm collar down the pipe section until it rests on the roof flashing. Figure 8.
9 Gas Information A. Fuel Conversions C. Gas Connection Before making gas connections ensure that appliance being installed is compatible with the available gas type. Any natural or propane gas conversions necessary to meet the appliance and locality needs must be made by a qualified technician using Hearth & Home Technologies specified and approved parts. Note: Have the gas supply line installed in accordance with local building codes, if any. If not, follow ANSI 223.1.
• Ensure that gas line does not come in contact with outer wrap of appliance. Follow local codes. • Incoming gas line should be piped into the valve compartment and connected to the 1/2 inch connection on the manual shutoff valve. WARNING Fire or Explosion Hazard • • • • Gas buildup during line purge may ignite. Purge should be performed by qualified technician. Ensure adequate ventilation. Ensure there are no ignition sources such as sparks or open flames. HIGH ALTITUDE INSTALLATIONS U.L.
10 Electrical Information A. Recommendation for Wire C. Intellifire Ignition System Wiring This appliance requires 110-120 VAC be wired to the junction box for proper operation of the appliance (Intellifire ignition). This appliance requires a 110 VAC supply to the appliance junction box for operation. A wiring diagram is shown in Figure 10.1.
DETAIL A BATTERIES RED BLACK GREEN ORANGE BATTERY 1 2 3 4 5 6 7 8 3V DC REAR VIEW GREEN IPI PILOT BROWN BROWN RED BROWN BROWN RED G Y R BLACK RED (MALE/FEMALE) FLAME SOLENOID RED (FEMALE/MALE) IPI MODULE RED BLACK IPI VALVE GROUND BLACK YELLOW (HNG) WHITE (HTL) R Y G WIRES WITH LABEL “FOR USE WITH REMOTE OR WALL SWITCH ONLY” (LOCATED UNDER FIREPLACE) FRONT VIEW FLAME ON RED RED ORANGE FLAME HIGH/LOW ADAPTER WIRES ORANGE AC PLUG YELLOW BLACK YELLOW FAN THERMOSTAT BLACK F
D. Junction Box Installation Romex Connector If the box is being wired from the OUTSIDE of the appliance: 14/2WG • Remove the cover plate located on the outer shell - right side (see Figure 10.3). Cover Plate outside firebox • Install the supplied Romex™ connector in the cover plate. • Make all necessary wire connections and reattach the cover plate to the outer shell.
11 Finishing A. Mantel Projections B. Facing Material Figure 11.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the opening edge of the appliance. WARNING Fire Risk. • Facing and/or finishing material must never overhang into the glass opening. Finishing materials must not interfere with: • Operation of louvers or doors. • Access for service.
WARNING Fire Risk. Finish all edges and fronts to clearances and specifications listed in manual. • Finishing material must NEVER pass the 1/2 inch metal edge around opening and overhang into glass opening. • Only non-combustible material (using 300º F. Minimum adhesive, if needed) can be applied as facing to fireplace surround in first 4 inches from opening sides and 6 inches above the opening. • Install combustible materials only up to specified clearances on top, front and side edges.
12 Appliance Setup A. Remove Shipping Materials E. Ember Placement Remove shipping materials from inside or underneath the firebox. B. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity. C. Accessories Install approved accessories per instructions included with accessories. See Service Parts List for appropriate accessories. Refer to Section 16. WARNING Explosion Risk. • Follow ember placement instructions in manual.
F. Positioning the Logs Log Assembly: LOGS-ESCAPE CAUTION: Logs are fragile! Carefully remove the logs from the packaging. 6 7 2 1 3 5 4 8 1 Step 1. Place the grate onto the burner. The back of the right tine drops into the hole on the right rear of the burner. The shorter left tine is pushed back into the half-hole on the left side of the burner. Be sure to push the grate all the way down to the floor and firmly back into its holder. LOG #1 (SRV750-706) (TWO): There are quantity two (2) of log #1.
LOG #2 (SRV569-705): Place log #2 on the left side of the burner resting on top of log #1, the grate tine, and on top of the pilot bracket. The log will rest touching the side of the firebox. The purpose of this log is to help disguise the pilot. Do NOT have the log touching the pilot or pilot operation may be affected. 2 LOG #3 (SRV2012-161): Place log #3 onto the back of the burner. The log sits on the bend up tabs and top of the burner surface.
LOG #5 (SRV2012-163): Place log #5 in front of log #4. The groove in the bottom end of the log fits into the right vertical tine of the grate. The back of the log rests in the groove on top of log #3. 3 4 5 LOG #6 (SRV2012-164): Place log #6 on the left side of the grate with the groove on the end of the log fitting into the vertical left tine of the grate. The burned end of the log rests in the groove on the left side of log #3. 3 6 LOG #7 (SRV2012-165): Place log #7 on top of log #6.
LOG #8 (SRV2012-166): Place log #8 on top of log #5. The flat bottom of log #8 sits on the large flat area of log #5. The burned end of log #8 rests on the second vertical tine from the right of the grate. Slide the log to the right until the “burner chunk” on the bottom of the log rests against the grate tine. Final Step: Place MYSTIC EMBERS generously around on the floor of the fireplace. Some can be spread out on the burner surface to blend the transition.
G. Glass Assembly H. Grilles and Trim WARNING Handle glass doors with care. • Inspect the gasket to ensure it is undamaged. • Inspect the glass for cracks, chips or scratches. • Do NOT strike, slam or scratch glass. • Do NOT operate appliance with glass door removed, cracked, broken or scratched. • Replace glass door assembly as a complete appliance. Removing Glass Assembly • Remove the ash lip that is located in front of the glass. • Remove the side panels located in front of the glass.
13 Operating Instructions A. Before Lighting Appliance Before lighting this appliance determine if it has a Standing Pilot or Intellifire ignition system by opening the control access panel to view wiring system and gas valve. If this appliance has a red or black ignitor button (see Figure 10.1) this appliance has a Standing Pilot ignition system. If there is no red or black ignitor button, this appliance has an Intellifire ignition system.
B. Lighting Appliance IPI Ignition FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance is equipped with an intermittent pilot ignition (IPI) device which automatically lights the burner. Do not try to light the burner by hand. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. B.
C. After Appliance is Lit CAUTION Initial Break-in Procedure When you light the appliance, you may notice that it produces heat which does have an associated odor or smell. If you feel this odor is excessive it may require the initial three to four hour continuous burn on high followed by a second burn up to 12 hours to fully drive off any odor from paint and lubricants used in the manufacturing process. Condensation of the glass is normal.
14 Troubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. A. Intellifire Ignition System Sympton 1. The ignitor/module makes noise, but no spark. 2.
Intellifire Ignition System - (continued) Symptom 3. (Continued) Pilot lights but continues to spark, and main burner will not ignite. (If the pilot continues to spark after the pilot flame has been lit, flame rectification has not occurred.) 4. Pilot sparks, but Pilot will not light. 46 Possible Cause Corrective Action c. Module is not grounded. Verify that module is securely grounded to metal chassis of appliance. Verify that wire harness is firmly connected to module. d.
15 Maintaining and Servicing Appliance A. Maintenance Tasks Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualified service technician should perform an appliance checkup at the beginning of each heating season. CAUTION WARNING Risk of injury or property damage. Before servicing: • Turn off gas. • Turn off electricity to appliance. • Disable remote control, if one is present. • Ensure appliance is completely cooled.
B. Replacing Light Bulb 1. Remove the front and glass by following the “Placing the Embers Material” section. 2. Remove the logs and grate. 3. Remove the burner by unscrewing the two screws on the back of the burner and the two screws by the pilot using a 1/4 inch hex driver. Gently move the pilot out of the way and slide the burner out. CAUTION Skin oils can cause early bulb failure. • Do not touch bulb with bare hands. • Use paper towel or rubber gloves when handling bulb.
Inspect Doors, Surrounds and Fronts Maintenance Tasks 1. Assess condition of screen and replace as necessary. Recommend addition of screen if one is not present. 2. Inspect for scratches, dents or other damage and repair as necessary. 3. Verify no obstructions to airflow through the louvers. 4. Verify maintenance of proper clearance to combustible household objects. Gasket Seal, Glass Assembly and Glass 1. Inspect gasket seal and its condition. 2.
16 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.
B. Vent Components Diagrams Pipe Effective Height/Length DVP4 DVP Pipe (see chart) 10-1/2 in. (267 mm) Effective Length Inches Millimeters 4 102 DVP6 6 152 DVP12 12 305 DVP24 24 610 DVP36 36 914 DVP48 48 1219 DVP6A 3 to 6 76 to 152 DVP12A 45 ° 4-7/8 in. ( 276 mm) 10-7/8 in. (276 mm) ° DVP45 (45 Elbow) 3 to 12 76 to 305 DVP12MI 3 to 12 76 to 305 DVP24MI 3 to 24 76 to 610 11-3/8 in. (289 mm) 10 in. (254 mm) 10 in. (254 mm) 1 in. (25 mm) 7-3/8 in. (187 mm) 24 in.
B. Vent Components Diagrams (continued) Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B will be required. 8 in. (203 mm) Heat Shield 15-1/8 in. (384 mm) Term Cap Minimum Effective Length Maximum Effective Length 3-1/8 in. 4-5/8 in.
B. Vent Components Diagrams (continued) 31 in. (787 mm) 13-1/4 in. (367 mm) 24-5/8 in. (625 mm) 27-1/2 in. (127 mm) 24-5/8 in. (625 mm) 13-1/4 in. (367 mm) RF6M Roof Flashing Multi-pak RF12M Roof Flashing Multi-pak 5 in. (127 mm) 13-3/4 in. (349 mm) 11-7/8 in. (302 mm) 5 in. (127 mm) 13-7/8 in. (352 mm) 13-3/4 in. (349 mm) DVP-BEK2 DVP-HPC Cap Brick Extension BEK Trap Cap Brick Extension 11-5/8 in. (295 mm) 12-1/8 in. (308 mm) 7-1/8 in. (181 mm) 5-3/4 in.
B. Vent Components Diagrams (continued) PVK-80 (For use with IPI and DSI appliances only.) 7-1/4 in. (184 mm) 12-1/2 in. (318 mm) 5-1/4 in. (133 mm) DVP-TVHW VerticalTermination Cap (Highwind) 1 in. (25 mm) 7-1/4 in. (184 mm) 14 in. (356 mm) 3/8 in. (10 mm) 1 in. (25 mm) 7-3/4 to 10-3/8 in. (197 to 264 mm) DVP-FBHT FireBrickTermination Cap Figure 16.5 DVP vent components 54 Heat & Glo • Escape-36DV • 2012-900 • Rev.
ESCAPE-36DV C. Service Parts Beginning Manufacturing Date: Sept. 2003 Ending Manufacturing Date: ______ Service Parts Diagram 9 10 12 11 13 15 14 Log Set Assembly 5 3 2 7 6 1 4 8 1 Part number list on following page. Heat & Glo • Escape-36DV • 2012-900 • Rev.
C. Service Parts List ESCAPE-36DV IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.
ESCAPE-36DV C. Service Parts Beginning Manufacturing Date: Sept. 2003 Ending Manufacturing Date: ______ Valve Assembly Parts List 7 2 5 1 4 6 3 8 IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.
D. Limited Lifetime Warranty Hearth & Home Technologies LIMITED WARRANTY Hearth & Home Technologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purchased from an authorized HHT dealer and installed in the United States of America or Canada. Warranty starts with date of purchase by the original owner (End User) except as noted for replacement parts.
D. Limited Lifetime Warranty (continued) • This limited warranty does not extend to or include surface finish on the appliance or terminations, door gasketing, glass gasketing, glass discoloration, firebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or corrosion on any of the metal surfaces, cast iron components, baffles, firepots, doors, or firebox area are not covered by this warranty.
E. Contact Information Heat & Glo, a brand of Hearth & Home Technologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 www.heatnglo.com Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer, please visit www.heatnglo.com.
