6

ManualsBrandsHeath Zenith ManualsAccessories for electricalEnergy Star SL-566

100 Watt H.P.S.

Dusk-to-Dawn Security Light

Installation Instructions With Two Piece Arm

READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION.

NOTE: All wiring must be run in accordance with the National Electrical Code (Canadian Electrical Code in Canada) through

conduit or another acceptable means. Contact a qualiﬁed electrician if there is any question as to the suitability of

the system.

Lens/Reﬂector

Assembly

Mounting

Arm

Lag Screw (4)

Flat Washer (10)

Mounting

Bracket

Photocontrol

Ground

Screw

1. Select a location on a ﬂat wall with structurally sound wood and

from 10 to 25 feet (3 to 7.6 m) from the ground. The wood should

be at least one inch thick to safely secure the ﬁxture.

2. Slide the curved section of the mounting arm into the mounting

bracket. Tighten the bolts on the mounting bracket evenly.

3. Using the mounting arm and bracket as a guide mark four mount-

ing holes. We suggest drilling 3/16" (4.8 mm) pilot holes for the

lag screws.

4. Mount the arm and bracket using four lag screws and washers

provided.

5. Place a ring of silicone caulk around mounting arm (see illustra-

tion). Slide the straight section of the mounting arm on to the

curved section aligning the predrilled holes.

6. Secure the two sections with two bolts, nuts and four washers

provided. Place silicone caulk on top of the bolts and washers

to prevent water from entering.

7. Thread your outdoor cable or ﬂexible conduit through the mount-

ing arm.

8. Loosely connect the mounting strap to the ﬁxture using two bolts

provided.

9. Slide the ﬁxture on to the mounting arm until the ﬁxture comes

to a stop. Secure the ﬁxture to the mounting arm by tightening

the two mounting strap bolts.

10. Connect the ﬁxture wires to the service wires using the wire nuts

provided (black to black and white to white). Push the connec-

tions as far as possible into the straight arm.

11. This ﬁxture must be grounded. Connect the service ground under

the head of the green ground screw and secure to the mounting

strap.

12. Install the lens/reﬂector assembly with two screws and washers

provided.

13. Screw in the 100 watt H.P. Sodium type S54 lamp provided.

14. Loosen the screw in the center of the photocontrol socket two

turns. Twist the socket so that the arrow points north. Note: There

is a stop to prevent the socket from turning all the way around. If

you have trouble turning the socket, try turning it the other direc-

tion. Retighten the screw in the center of the socket.

Mounting Strap

Silicone

Caulk

15. Align the photocontrol (it will only plug-in one way). Plug it in

and twist clockwise until it stops.

To test operation during daylight, cover the photocontrol with a

small box. Turn on the power. Not all photocontrols are alike. Some

may have a time delay of a few minutes, others will turn on as soon

as power is applied. The light will take up to ten minutes to reach

full brightness. Uncover the photocontrol and your unit will operate

automatically—on at dusk, off at dawn.

Model SL-5666

WARNING: Turn power off at the circuit breaker or

fuse.

Lamp in Fixture Contains Mercury. Dispose According

to Local, State, or Federal Laws.

Summary of content (12 pages)

PAGE 1
Model SL-5666 100 Watt H.P.S. Dusk-to-Dawn Security Light Installation Instructions With Two Piece Arm READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION. NOTE: All wiring must be run in accordance with the National Electrical Code (Canadian Electrical Code in Canada) through conduit or another acceptable means. Contact a qualified electrician if there is any question as to the suitability of the system. Lamp in Fixture Contains Mercury. Dispose According to Local, State, or Federal Laws.
PAGE 2
Installation Instructions Without Two Piece Arm READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION. NOTE: All wiring must be run in accordance with the National Electrical Code (Canadian Electrical Code in Canada) through conduit or another acceptable means. Contact a qualified electrician if there is any question as to the suitability of the system. Lamp in Fixture Contains Mercury. Dispose According to Local, State, or Federal Laws.
PAGE 3
Ballast Assembly Replacement Instructions Red Red Blue Black White White White White Blue Black 1. Remove bulb. 2. Loosen two screws holding plastic/aluminum reflector and remove reflector. 3. Remove two screws connecting ballast assembly to aluminum housing. 4. Remove tape from wire bundle. Be careful not to damage wires. 5. Label wires according to wiring diagram. 6. Remove wire nuts from wires. Retain wire nuts to connect replacement ballast assembly. 7.
PAGE 4
Technical Service Please call 1-800-858-8501 (English speaking only) for assistance before returning product to store. If you experience a problem, follow this guide. You may also want to visit our Web site at: www.hzsupport.com. If the problem persists, call* for assistance at 1-800-858-8501 (English speaking only), 7:30 AM to 4:30 PM CST (M-F). You may also write* to: HeathCo LLC P.O.
PAGE 5
Modelo SL-5666 Lámpara de Seguridad de Sodio de Alta Presión (H.P.S.) del Crepúsculo al Amanecer de 100 Vatios Instrucciones para instalación con brazo de dos piezas ANTES DE EMPEZAR LA INSTALACIÓN LEA CUIDADOSAMENTE TODAS LAS INSTRUCCIONES NOTA: Todo el cableado debe realizarse de acuerdo con el Código Nacional Eléctrico (Código Eléctrico Canadiense en Canadá) usando tubería u otro medio aceptable.
PAGE 6
Instrucciones para instalación sin brazo de dos piezas ANTES DE EMPEZAR LA INSTALACIÓN LEA CUIDADOSAMENTE TODAS LAS INSTRUCCIONES NOTA: Todo el cableado debe realizarse de acuerdo con el Código Nacional Eléctrico (Código Eléctrico Canadiense en Canadá) usando tubería u otro medio aceptable. Contáctese con un electricista calificado si tiene alguna pregunta respecto a la adaptabilidad del sistema. La lámpara en el dispositivo contiene mercurio.
PAGE 7
Instrucciones para el cambio del conjunto estabilizador Azul Azul Negro Blanco Blanco Blanco Blanco Rojo Rojo Negro 1. Retire la bombilla. 2. Afloje los dos tornillos que sostienen el reflector plástico/aluminio y retire el reflector. 3. Retire los dos tornillos que conectan el conjunto estabilizador a la caja de aluminio. 4. Retire la cinta del paquete de cables. Tenga cuidado de no dañar los cables. 5. Marque los cables según el esquema eléctrico. 6.
PAGE 8
SERVICIO TÉCNICO Favor de llamar al 1-800-858-8501 (sólo para hablar en inglés) para pedir ayuda antes de devolver el producto a la tienda. Si tiene algún problema, siga esta guía. Usted puede también visitar nuestro sitio Web: www.hzsupport.com. Si el problema continúa, llame al 1-800-858-8501 (sólo para hablar en inglés), de 7:30 AM a 4:30 PM CST (L-V). Usted puede también escribir a: HeathCo LLC P.O.
PAGE 9
Luminaire de sécurité crépuscule-aurore au sodium haute pression (SHP de 100 W) Modèle SL-5666 Mode d’installation du modèle avec bras en deux pièces LIRE SOIGNEUSEMENT LES DIRECTIVES AVANT D'ENTREPRENDRE L’INSTALLATION. NOTE : Le câblage doit être conforme aux exigences du Code canadien de l’électricité et être installé dans des canalisations ou autres dispositifs acceptables. Si vous avez des doutes concernant la convenance du système, consultez un électricien reconnu. le nord.
PAGE 10
Mode d’installation du modèle sans bras LIRE SOIGNEUSEMENT LES DIRECTIVES AVANT D’ENTREPRENDRE L’INSTALLATION. NOTE : Le câblage doit être conforme aux exigences du Code canadien de l’électricité et être installé dans des canalisations ou autres dispositifs acceptables. Si vous avez des doutes concernant la convenance du système, consultez un électricien reconnu. La lampe du luminaire contient du mercure. Mettez-la aux rebuts conformément aux lois locales, provinciales ou fédérales.
PAGE 11
Directives de remplacement du ballast Bleu Noir Blanc Blanc Blanc Bleu Blanc Noir Rouge Rouge 1. Retirez l’ampoule. 2. Desserrez les deux vis qui retiennent le réflecteur de plastique et d’aluminium, puis enlevez le réflecteur. 3. Retirez les deux vis qui fixent le ballast au boîtier d’aluminium. 4. Enlevez le ruban adhésif du faisceau de fils en prenant bien soin de ne pas endommager les fils. 5. Étiquetez les fils conformément au diagramme de câblage. 6.
PAGE 12
SERVICE TECHNIQUE Veuillez faire le 1 800 858-8501 (service en anglais seulement) pour obtenir de l’aide avant de retourner l’article au magasin. En cas de problème, suivez ce guide. Vous pouvez aussi visiter notre site Web à www.hzsupport.com. Si le problème persiste, composez* le 1 800 858-8501 (service en anglais seulement), entre 7 h 30 et 16 h 30, HNC, du lundi au vendredi. Vous pouvez aussi écrire au : HeathCo LLC P.O.