Installation Instructions

ManualsBrandsHeath Zenith ManualsLighting & Ceiling FansWhite Dual Head Outdoor Security Flood Light

204021-01

3. Loosen the side bolt connected to the arm to aim the ﬁxture up

and down.

4. For a rain tight seal, caulk the aiming arm joint with silicon

caulking compound.

Compact Twin 150 Watt Halogen

Fixture Installation Instructions

To avoid Electrical Shock:

Wiring Fixture

Connect all white

wires together

Connect all black

wires together

Model 5502

The Heath

/Zenith Compact Twin Halogen disperses light over a wide area. It includes two 150W halogen lamps, mounting plate

for standard junction box and is for use with 120VAC.

FOR PROPER INSTALLATION AND OPERATION, PLEASE READ THESE INSTRUCTIONS CAREFULLY.

To Avoid Fire or Burn Hazards:

• Allow xture to cool before touching. The bulb and the xture operate at high temperatures.

•

Keep ﬁxture at least 2" (51 mm) from combustible materials. Do not aim at objects closer than 3 feet (1 m).

•

Use up to 150 watt lamp maximum per lampholder.

+/- 4°

Junction box ground

wire to green ground

screw on ﬁxture

No Service Parts Available for this Product

Cover Plate

1. Connect the lamp wires to the power source wiring. Secure with

wire connectors.

2. Attach the cover plate to the junction

box (Apply silicon caulk between

cover plate and junction box for

a raintight seal). Keep the fixture

horizontal (within +/- 4°) so the bulb

inside is horizontal. If the bulb is not horizontal, the bulb may

darken or shatter and fail prematurely.

WARNING: Turn power off at the circuit breaker or

fuse.

• Grounding and installations must comply with local codes and

the National Electric Code (Canadian Electrical Code).

• This product should be mounted on a grounded junction box and

must be used with a threaded cover plate.

• Permanently mount the xture to a building or pole. This xture

is for outdoor use and is wall and eave mountable.

Bulb Installation and Replacement

CAUTION: When replacing bulbs, turn power off and

let the ﬁxture cool.

NOTE: Bulbs are included, but need to be installed. The bulbs

are located behind the glass cover of each lamp head.

1. Open lamp head with a phillips head screwdriver. To remove the

old bulb, push the bulb towards the right until the left side of the

bulb is clear of the left socket.

2. To install the bulb, place one end of the bulb on the contact in

the right socket. While pushing the bulb against the right con-

tact, lower the other end of the bulb onto the contact in the left

socket.

3. Spin the bulb to verify it is seated properly.

4. Close the lamp head and tighten locking screw securely.

Important: Use a clean glove or cloth when handling the

new bulb. Use isopropyl (rubbing) alcohol to clean the bulb

if it is touched with your bare hands.

Left Socket

Right Socket

Contact

Bulb Lamp Head

Glass Cover

Summary of content (4 pages)

PAGE 1
Model 5502 Compact Twin 150 Watt Halogen The Heath®/Zenith Compact Twin Halogen disperses light over a wide area. It includes two 150W halogen lamps, mounting plate for standard junction box and is for use with 120VAC. FOR PROPER INSTALLATION AND OPERATION, PLEASE READ THESE INSTRUCTIONS CAREFULLY. To Avoid Fire or Burn Hazards: • Allow fixture to cool before touching. The bulb and the fixture operate at high temperatures. • Keep fixture at least 2" (51 mm) from combustible materials.
PAGE 2
Modelo 5502 Halógenas compactas gemelas de 150 vatios Las halógenas compactas gemelas de Heath®/Zenith dispersan luz a través de una amplia área. Viene con dos bombillas halógenas de 150 vatios, placa de montaje para una caja de empalmes estándar y se la debe usar con 120 VCA. PARA SU CORRECTA INSTALACION Y FUNCIONAMIENTO, POR FAVOR LEA CUIDADOSAMENTE ESTA INSTRUCCIONES. Para evitar pellgros de fuego o de quemazón: • Deje que el artefacto se enfríe antes de tocarlo.
PAGE 3
Modèle 5502 Luminaire Halogène Compact Double de 150 W Le luminaire halogène compact jumelé Heath®/Zenith éclaire une grande surface. Il comprend deux ampoules halogènes de 150 W, une plaque de montage pour boîte de jonction standard et est conçu pour le 120 V CA. LIRE SOIGNEUSEMENT LES DIRECTIVES AVANT D’ENTREPRENDRE L’INSTALLATION. Pour éviter les risques de brûlure ou d’incendie: • Laissez refroidir le luminaire avant de le toucher. L’ampoule et le luminaire fonctionnent à haute température.
PAGE 4
TWO YEAR LIMITED WARRANTY This is a “Limited Warranty” which gives you specific legal rights. You may also have other rights which vary from state to state or province to province. For a period of two years from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you.