Item #0000000000 Model #HB-7903-02 USE AND CARE GUIDE D R A FT C O P Y WIRELESS MOTION ALERT DOORBELL KIT Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday 1-844-760-3644 HAMPTONBAY.COM Illustrations may vary from actual unit. THANK YOU We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this wireless motion alert doorbell kit.
Table of Contents Table of Contents........................................2 Safety Information......................................2 Warranty.....................................................2 3-Year Limited Warranty.........................2 Pre-Installation...........................................3 Planning Installation...............................3 Specifications.........................................3 Tools Required........................................3 Hardware Included..................
Pre-Installation PLANNING INSTALLATION Before installing the wireless motion alert doorbell kit, ensure that all parts are present. Compare the parts with the Hardware Included and Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this wireless motion alert doorbell kit. Estimated installation time: 30 minutes SPECIFICATIONS Power requirements Doorbell Push button Motion sensor 120V, 60 Hz Type A23 12V battery (included) 2x - Type “AAA” 1.
Pre-Installation (continued) PACKAGE CONTENTS A B C Part Description Quantity A Doorbell 1 B Motion sensor 1 C Push button 1 Installation 1 Installing the doorbell □□ Plug in the doorbell (A) at the desired location. A the batteries into the 2 Installing motion sensor B □□ Remove the screw and cover on the back of the motion sensor (B) using a small Phillips screwdriver (not included). □□ Install two “AAA” batteries. Ensure the batteries are oriented correctly.
Installation (continued) 3 Removing the battery tab C □□ Remove the backs of the push button (C) by pushing in the tab on the bottom with a small flathead screwdriver (not included). □□ Remove the orange battery tab from the push button (C). 4 Testing the push button and doorbell C □□ Temporarily position the push button (C) where it will be mounted. □□ Press the push button (C) to verify the doorbell (A) and push button (C) work properly.
Installation (continued) 6 Mounting the push button Use either screws (BB) or double-sided tape (CC) to mount the push button (C). □□ To mount with screws (BB), remove the back of the push button (C) by pushing in the tab on the bottom with a small flathead screwdriver. Place the back of the push button (C) on the door jamb and mark the two screw holes. Attach with screws (BB) and snap on the front of the push button (C).
Operation (continued) 2 Setting the sensor’s day detect The sensor (B) can be programmed to operate during the daytime only (DAY ONLY) or both day and night (DAY/NIGHT). DAY DETECT DAY ONLY B DAY/ NIGHT □□ Remove the batteries from the sensor (B). □□ Slide the “DAY DETECT” switch to the desired mode. Replace the batteries and cover. 3 Setting the sensor’s range The “RANGE” control increases and decreases the sensitivity of the sensor (B).
Operation (continued) 6 Selecting a push button tune NOTE: All doorbells are designed to play only two different tunes no matter how many push buttons are used. The doorbell (A) has different selectable tunes for different push buttons (sold separately). The push button (C) set as the “REAR” push button will only play “Ding” (one note tune). The push button set as the “FRONT” push button will play either “Ding-Dong” (two note tune) or Westminster (eight note tune).
Troubleshooting (continued) Problem Possible Cause Solution The doorbell sounds at night. □□ The day detect switch is in the “DAY/NIGHT” position. □□ The sensor is functioning correctly. If a doorbell alert is not desired at night, slide the day detect switch to the “DAY ONLY” position. The doorbell does not sound during the day. □□ The day detect switch is in the “DAY ONLY” position and the sensor is located in a dark area.
Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday 1-844-760-3644 HAMPTONBAY.COM Retain this manual for future use.
