Manual

ManualsBrandsHeatmaster ManualsFireplace/Gas Stove AccessoriesCape Fear Collection 18" Oak Vent Free Logs Only in Oak

WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS CAREFULLY AND WITHOUT

ERROR OR FAILURE TO HEED ANY AND ALL WARNINGS IN THESE INSTRUCTIONS CAN

RESULT IN AN EXPLOSION, FIRE OR THE PRODUCTION OF CARBON MONOXIDE GAS

WHICH CAN CAUSE PROPERTY DAMAGE, BODILY INJURY OR DEATH.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of

this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

•

Do not try to light any appliance.

•

Do not touch any electrical switch.

•

Do not use any telephone in your building.

•

Immediately call your gas supplier from a neighbor’s telephone.

•

Follow the gas supplier’s instructions.

•

If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or the

gas supplier.

This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is in-

stalled. Provisions for adequate combustion and ventilation air must be provided. Refer to

page 4.

This appliance is intended for supplemental heating.

ANSI Z21.11 2-2016 APPROVED / ANSI Z21.60-2017 CSA 2.26 2017

State and local codes may only allow operation of this appliance in a vented configuration. Check your local and state codes.

This appliance may be installed in an aftermarket, permanently located, manufactured (mobile) home,

where not prohibited by local codes. This appliance is only for use with the type of gas indicated on

the rating plate.

If the information in this manual is not followed exactly, a fire or explosion may result,

causing property damage, personal injury or loss of life.

WARNING

IM-149

10/2018

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Installation and Operating Instructions for Natural & LP Gas

Unvented Gas Log Heater

HM2-IPI-ECO and HM2-MIL

18", 24" and 30/33" BURNER UNITS.

IMPORTANT: READ INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTAL-

LATION OF THIS ROOM HEATER.

Summary of content (26 pages)

PAGE 1
Installation and Operating Instructions for Natural & LP Gas Unvented Gas Log Heater HM2-IPI-ECO and HM2-MIL 18", 24" and 30/33" BURNER UNITS. ANSI Z21.11 2-2016 APPROVED / ANSI Z21.60-2017 CSA 2.26 2017 State and local codes may only allow operation of this appliance in a vented configuration. Check your local and state codes.
PAGE 2
Important safety information • WARNING • • • Any change to this heater or its controls can be dangerous and void any warranty. Do not allow fans to blow directly into fireplace. Avoid drafts that alter burner flame patterns. Do not use a blower insert, heat exchanger insert or any other accessory not approved for use with this heater. Improper installation or use of this heater can cause serious injury or death from fire, burns, explosion or carbon monoxide poisoning.
PAGE 3
Important safety information cont Do not use this room heater if any part has been under water. Immediately call a qualified service technician to inspect the room heater and to replace any part on the control system and any gas control which has been underwater. This room heater is for installation in a solid fuel burning fireplace or listed unvented firebox enclosure only.
PAGE 4
PRODUCT SPECIFICATIONS MINIMUM SIZE FIREPLACE DIMENSIONS Gas Log Size Dimension 18" Height of Front Opening 15" Width of Front Opening Depth Width of Rear Opening 24" 15" 15" 21 1/2" 26 1/2" 35 1/2" 14" 14" 14" 16” 21” 25” BTU'S RATING 18" 24" BTU Ratings 30/33" 30/33” LP 33,000 40,000 40,000 NAT 34,000 40,000 40,000 General Instructions WARNING PROVISIONS FOR ADEQUATE COMBUSTION AND VENTILATION AIR This heater shall not be installed in a confined space or unusually tight const
PAGE 5
General Installation Information The following formula can be used to determine the maximum heater rating per the definition of confined space: Counter BTU/HR= (L1 + L2) FT X (W)FT X (H)FT X 1000 Fireplace 50 Example: Refer to Figure 1. Two (2) connecting rooms with and open area between , with the following dimensions. L1 = 15 1/2 L2 = 12 ’ H L2 W = 12 ’ L1 W Figure 1. Example of large room with 1/2 wall divider. H=8’ (15 1/2 + 12 ) x (12) x (8) x 1000 = 52800 btu.
PAGE 6
CLEARANCE/ HEIGHT REQUIREMENTS 10 8 6 2 1/2 Heat resistant material 14 12 10 8 6 2 1/2 24 5/8 20 1/2 28" Heat resistant material 26" 18 5/8 14 1/2 22 1/2" 8" Hood Figure 3. Minimum Mantel Clearance with No Hood. Figure 4. Minimum Mantel Clearance with Hood. Example: The bottom of a mantel may project from the wall a minimum of 14” above the opening. The top side of the mantel may project a maximum of 6” at a minimum of 20-1/2” above the opening.
PAGE 7
CLEARANCE/ HEIGHT REQUIREMENTS cont Heat resistant material ( minimum requirements) with wooden mantel or other combustible projection: 8" or more of heat resistant material 8” or more of heat resistant material To install the heater with a wooden mantel, shelf or other combustible projection above, first measure the heat resistant material shown in Figure 7. Heater in Fireplace or Firebox Figure 7. Measuring heat resistant material for mantel.
PAGE 8
FIREPLACE PREPARATION Before fully installing the unit: • • Turn OFF the gas supply to the fireplace or firebox. Seal any fresh air vents and/or ash clean-out doors located on the floor or wall of the fireplace. If left unsealed, drafting may cause pilot outage or sooting. Use a heat resistant sealant. Do not seal the chimney flue damper.
PAGE 9
MAINTENANCE OF THE SYSTEM Under normal use this appliance will require only limited cleaning. Constant airflow through this appliance will cause dust to collect on the burners, base and logs. An excessive build up of dust can cause the pilot and burners to operate incorrectly and produce high levels of carbon monoxide, a poisonous gas. To clean the burner and base, turn the control to OFF and allow the system to cool down. Remove top logs and front log very carefully.
PAGE 10
TROUBLESHOOT- HM2 MILLIVOLT WARNING Turn appliance OFF and allow to cool before servicing. Only a qualified service person should service and/or repair the heater. Note: All troubleshooting items are listed in order of operation. OBSERVED PROBLEM (Millivolt unit only) When igniter is pushed there is no spark at the ODS/pilot. POSSIBLE CAUSE 1. 2. 3. 4. 5. 6. Appliance produces unwanted odors. 1. 2. Appliance shuts off during use 1. 2. 3. 4. REMEDY Igniter electrode positioned wrong.
PAGE 11
TROUBLESHOOTING OBSERVED PROBLEM (Millivolt unit only) ODS/pilot lights, but flame goes out when control knob is released. HM2 MILLIVOLT Cont’ POSSIBLE CAUSE 1. 2. REMEDY 1. 2. 6. 7. Press in control knob fully. After ODS/pilot lights, keep control knob pressed in for 30 seconds. Fully open manual shutoff valve. Hand tighten until snug, then tighten 1/4 turn more. Contact your local gas company or clean the pilot. Replace thermocouple. Replace control valve. 6. 7. Control knob not fully pushed in.
PAGE 12
TROUBLESHOOTING OBSERVED PROBLEM Either the remote or switch are pressed to start the burner ignition sequence and there is no function or response. HM2 IPI ECO POSSIBLE CAUSE 1. 2. 3. 4. 5. 6. 7. 8. 9. Missing or weak batteries at power supply box or remote. Box is unplugged. The switch cable is not plugged into the module. Control valve wiring harness not plugged in or not in proper position. Remote not communicating with the control module. Igniter cable is not connected.
PAGE 13
TROUBLESHOOTING OBSERVED PROBLEM When igniter button is pressed on the remote or switch pad, the pilot sparks but there is no ignition. HM2 IPI ECO Cont’ POSSIBLE CAUSE 1. 2. 3. 4. 5. 6. 7. 8. Gas supply turned off or equipment shutoff valve is closed. Air in gas lines. Thermocouple circuit between the control valve and the control module is open. No gas to the ODS pilot. Depleted LP gas supply. Valve cable is disconnected or broken. ODS pilot is clogged. Gas appliance regulator is not correct.
PAGE 14
ECO Electronic Ignition FOR YOUR SAFETY READ BEFORE LIGHTING WARNING If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance is equipped with an electronic ignition pilot. This pilot lights itself with either the manual on/off button or with the remote control transmitter that is provided. B. B. BEFORE LIGHTING smell all around the appliance area for gas.
PAGE 15
MILLIVOLT FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly a fire or explosion may result causing property damage, personal injury, or loss of life. A. This appliance is equipped with a push button piezo ignition device, which can be used to light the pilot. If the piezo fails to ignite the pilot, then follow the instructions for lighting pilot with match. B. BEFORE LIGHTING smell all around the appliance area for gas.
PAGE 16
UNIT PLACEMENT Place the entire unit system in the center of the fireplace to allow proper air flow on all sides of the unit. GAS PIPING AND GAS PRESSURE REQUIREMENTS Check the type of gas that is supplied to your fireplace. Use only the gas type indicated on the heater’s rating plate. If the gas listed on the plate is not your type of gas supply, DO NOT INSTALL THE SYSTEM. Contact your dealer. All gas piping must be installed to comply with local and National Fuel Gas codes.
PAGE 17
INSTALLER: Please be sure the homeowner understands these key points. WARNING Periodically clean loose particles, dust and lint from pilot and front and rear burner ports. Clean burner air intake holes. Failure to do so may result in sooting and poor combustion. Logs and volcanic rock must be positioned correctly. Failure to do so may result in sooting and poor combustion. “All previously applied loose material must be removed prior to reapplication”. Do not operate ceiling fans while using this heater.
PAGE 18
Regular Oak 18” Log Part Numbers: 431 444 432 409 430 429 Regular Oak 24” Log Part Numbers 408 424 428 409 410 427 426 Page 18
PAGE 19
Regular Oak 33” Log Part Numbers: 407 411 274 408 410 409 406 405 Page 19
PAGE 20
Split Oak 18” Log Part Numbers: 441 438 416 415 440 439 Split Oak 24” Log Part Numbers: 437 415 416 438 435 Page 20 436
PAGE 21
Split Oak 33” Log Part Numbers: 433 414 434 415 416 274 413 412 Page 21
PAGE 22
Cape Fear Oak Log Placement The bottom of the front & back logs are notched so they can lay on the grate properly. The top of the front & back logs are also notched. These notches are to ensure no flame impingement.
PAGE 23
GUIDELINES FOR APPLICATION/MAINTENANCE OF ODS PILOTS Technical Application: 1. For accurate and consistent ODS intervention (cutoff) performance, the applied ODS must always be connected to a control valve having a preferred dropout rating of 80mA and not less than 65mA. 2. Proper connection of thermocouple to gas safety valve is made by tightening the connection nut by hand and then turning it 1/4 turn using the proper sized wrench. Do not over tighten as damage to safety valve may result. 3.
PAGE 24
HM2 IPI ECO PARTS LIST Parts List D A Grate Assy B F N G E C Remote Transmitter O M L K H I J Key Letter Part Number Description Key Letter Part Number Description A 11-1181B 18”Burner I 01-1075 HI/Low Switch A 11-1182B 24” Burner J 01-1074 Learn Switch A 11-1183B 33” Burner K 16-1070 Battery Pack B 07-1034 LP Regulated Valve w/ Harness L H-0586-B EcoFlow Battery Holder Log B 07-1034 Natural Regulated Valve w/ Harness M 09-0996 Remote Transmitter C 07-1039
PAGE 25
HM2 MILLIVOLT PARTS LIST ON/OFF Switch Millivolt Valve Cover Plate Grate Peizo Pilot Regulator Natural Only ODS Pilot PART 18” 24” 33” Burner 11-1181B 11-1182B 11-1183B Grate 11-1265B 11-1270B 11-1275B Cover Plate 11-1294 11-1294 11-1294 Pilot Brkt Millivolt Not shown 16-1100 16-1100 16-1100 Valve Brkt Millivolt Not shown 16-1121 16-1121 16-1121 Millivolt LP Valve 16-1030 16-1030 16-1030 Millivolt NG Valve 16-1035 16-1035 16-1035 Millivolt ODS LP Pilot 16-1040 16-1040
PAGE 26
HEATMASTER, LLC LIMITED WARRANTY All refractory cement logs manufactured by Heatmaster LLC have a lifetime warranty against breakage due to heat to the original owner in the original installation. All other logs supplied from Heatmaster LLC have a 2 year warranty against breakage due to heat to the original owner in the original installation. All metal parts, including burners and grate assemblies, are warranted for 5 years. All other mechanical parts are warranted for 1 year. LIMITATIONS 1.