CONTROLS for HEATSTRIP HEATERS PRODUCT MANUAL
HEATSTRIP CONTROLS REV D JUL15 To improve control of Heatstrip outdoor heaters, there are a range of solutions to help you increase the use of your outdoor entertaining area.
HUSA03 SINGLE ROCKER SWITCH SPECIFICATIONS Can control one heater or one set of heaters Wireless wall switch Detachable face plate Fits inside standard junction box HUSA04 DOUBLE ROCKER SWITCH SPECIFICATIONS Can control two heaters or two sets of heaters Wireless wall switch Detachable face plate Fits inside standard junction box
HUSA05 RELAY SPECIFICATIONS Frequency 902MHz Transmission Range 80ft(25m) Dimensions 2.78” x 1.65” x 1.1” (73 x 42 x 28mm) Weight 3.02 Oz (90g) Compliance ETL FCC: SZV-STM300U IC: 5713A-STM300U Surge Protection 3000 volts Line voltage 120, 208. 240 volts Current 16 amps The relay receives wireless messages from a switch to turn the Heater on or off. The relay can control one heater only. FEATURES ON/OFF control of the heater Timer OFF function, 15, 30, 45, 60 minutes.
INSTALLATION Can be mounted inside a standard junction box, Attached using a standard knockout and thread connector with nut (included). The Relay is to be mounted indoors only and protected from the environment. Use a non-metal electrical enclosure for best RF transmission. Install in a suitable location taking care with interference through walls and other obstacles. When the relay is first installed, the relay will go through a start up sequence.
LIGHT TABLE Menu Set NORMAL Operation, Heater is on, relay is closed solid NORMAL Operation, Heater is off, relay is open solid Basic set up Advanced set up Auto Off set up Menu Set To exit any menu, hold both buttons 2 seconds Option is pending blink Active setting blink RESTORE FACTORY SETTINGS To restore factory settings, hold both buttons until Menu is solid red and Set is solid Amber (approx 15 seconds) solid solid Press and hold for Set for 3 seconds Start, you can now follow the se
LINKING RELAY TO SWITCHES & REMOTE CONTROL Menu Set 1. NORMAL operation, relay needs to be in this position. solid 2. To enter Setup menu, press both buttons for 2 seconds 3. Ready to accept new links, the link will stay open for 2 minutes. The Menu light will continue to blink once as long as the relay is in the Setup menu. 1 1 4. Press the ON button 3 times in quick succession. Only one switch/remote control can be linked at a time. 5. The relay will toggle on and off.
UNLINK SWITCH Menu Set 1. NORMAL operation, relay needs to be in this position. solid 2. To enter Setup menu, press both buttons for 2 seconds 3. Ready to accept new links, the link will stay open for 2 minutes. 1 1 Menu Set 4. Press the Set button 3 times 1 3 Blink 5. Press the ON button 3 times in quick succession. Only one switch/remote control can be unlinked at a time. 6. The relay will toggle on and off. Set light will be solid for 3 seconds. 7.
SET UP AUTO OFF FUNCTION The relay comes with an option to program in an Auto-Off function. The factory default auto off is disabled to begin with. The Auto-Off is active all the time once programmed. To change it, you’ll need access to the relay and to go through this program again. Menu Set 1. Start, Relay needs to be in either of the two modes solid 2. To enter Setup menu, press both buttons for 2 seconds 3. Relay is ready to accept change of Menu 1 1 4 1 4.
HUSA04 REMOTE CONTROL SPECIFICATIONS Small handheld Can control two heaters or two sets of heaters RANGE: 80 feet FREQUENCY: 902 MHz CHANNELS: 4 buttons ( 2 orckers0 DIMENSIONS: 1.85 x 3.15 x .
WIRING DIAGRAMS All wiring must be carried out by a licensed electrician and according to local building codes. Diagrams are indicative and must be installed with required isolators, RCDs, fuses, or circuit breakers.
Warranty Terms & Conditions The below Warranty Terms and Conditions apply for International Customers. Heatstrip USA warrants to the original owner that HEATSTRIP® Controller products will be free from defects in materials and workmanship for a period of 12 months from the date of purchase in accordance with the following warranty terms and conditions.