HF 380 AIR PURIFIER HF 3 INSTRUCTION MANUAL HEAVEN FRESH ©2010, HFFR-CANFR-HF 380-03/11
Thank you for purchasing the efficient Heaven Fresh HF 380 Air Purifier. We wish you many years of healthy indoor air with this innovative product. Ensure that all safety precautions are followed when using electrical appliances for the proper operation of the device. This instruction booklet describes the safety precautions to be observed during operation to prevent injuries to yourself, other persons and damage to the device.
COMPONENTS [ Front View ] Air Outlet Dust Sensor CLEAN METAL GRID REPLACE FILTER RESET Air Inlets Air Inlets Bottom Stand [ Control Panel ] Receiver port Odour Sensor CLEAN METAL GRID REPLACE FILTER RESET Heaven Fresh 2 3 HF 380
COMPONENTS [ Back View ] [ Interior View ] Plasma Dust Collector (Metal grid) Heaven Fresh 4 HF 380
BEFORE USING BEFORE USING Follow these steps to optimize accuracy of clean air sensors: Follow these steps to optimize accuracy of clean air sensors: 1. Run the unit for a couple hours or more. 2. During this time, also increase ventilation in the room as much as possible, odour even opening a window if the air outside is at least fairly clean. odour 3. Unplug the HF 380, then immediately plug it in, turn it on, and resume operation.
EXPLANATION OF INDICATORS Odour odour odour odour odour, Heaven Fresh 6 HF 380
OPERATING INSTRUCTIONS (1 ft) from to turn off Timer duration duration Heaven Fresh 7 HF 380
CLEANING AND MAINTENANCE During cleaning and maintenance, please turn off and disconnect the plug from the power outlet. is Disassembling the device Assemble the Removing Push the plasama dust collector towards the base of the device. Use your foot or knee if needed to hold the base in place. Push the two tabs inward and lift up the dust collector.Hold the top of the unit (where the control panel is) down to help pull out the collector grid.
CLEANING AND MAINTENANCE from Plasma Dust Collector R 11 8 with running & avoid scratching the coating on the cover.
CLEANING AND MAINTENANCE C CLEAN METAL GRID REPLACE FILTER making sound RESET Remove 8 2. Lift up the tab at the top of the plastic housing for the metal dust collector gird. Once this tab is open,remove the dust collector. Please wear protective gloves to avoid any cuts on your fingers. CAUTION Please keep in mind that electrical wires of the Plasma Dust Collector Plate are fragile and special care is required while cleaning.
CLEANING AND MAINTENANCE use warm water If the dirt is hard to remove, pre-soak in diluted detergent and then use a toothbrush to clean. Please beware not to damage any wiring while cleaning the dust collector.
CLEANING AND MAINTENANCE CLEAN METAL GRID REPLACE FILTER RESET 8 Replacing the UV lamp the 10 the not functioning, Remove replace with Carefully Resetting After cleaning and replacing filters, reset the CLEAN METAL GRID and REPLACE FILTER indicators. Otherwise the two indicators would remaining glowing after turning on the unit. While resetting, the unit should remain plugged into the socket, but the uint itself should be turned off.
CLEANING AND MAINTENANCE Take out Put back the sensor correctly after cleaning, make sure that the cord is reconnected in the correct direction.
FREQUENTLY ASKED QUESTIONS Clean Air Monitor Q. Why does only one LED light glow under "Clean Air Monitor"? A. First, the air may have been clean the whole time. Or, the air purifier may be positioned where the sensor is too far away from the airborne pollutants and irritants. If this is the case, relocate the unit where it is close to the source of indoor air pollution. To test the sensor, stir dust or increase pollution near the sensor.
FREQUENTLY ASKED QUESTIONS Q. odour? is 10 Check the electrical discharge wires to make sure they have not been disconnected or broken. If they are, please fix or contact the distributor for a replacement. Q. Is it firmly plugged into the wall socket? Please check to make sure it is. Has the unit been properly reassembled after being cleaned? Please confirm. The unit will not operate if the plasma dust collector or the front cover is not properly installed. APPLICABLE AREAS 650 ft² (60.
APPLICABLE AREAS 650 ft² (60.4 m²) living SPECIFICATIONS Model: NatruroPure™ HF 380 Rated Voltage: AC 110~120V/50~60Hz. (North America) AC 220~240V/50~60Hz. (Europe and Asia) Power consumption: 80 W (High Setting) Ion output: > 4,000,000 / cm³ UV: 20uw (254 Nanometers) Dust Removal Rate: 99.97% Noise Level (dB): Silent (20) Low (35) Med (45) High (52) Air Volume: 106 ft³ (3.0 m³) per Minute (High Setting) Dimensions: 13.5" (L) x 10.0" (W) x 24.0" (H) 34.3 (L) x 25.4 (W) x 61.0 (H) (cm) Weight: 15 lbs ( 6.
WARRANTY CERTIFICATE WARRANTY CERTIFICATE FOR THE MULTI-FUNCTIONAL PURIFICATION SYSTEM HF 380 Date of purchase: Customers name: Address: Telephone: Email: Seller’s name: Address: 1. Please fill in completely this Warranty Certificate. Send it with the invoice and the unit, postage pre-paid and using the original packing box, to your distributor. Make sure to include the appropriate return postage for the package. 2.
Heaven Fresh 18 HF 380
WARRANTY INFORMATION Heaven Fresh products are subject to strict quality control before leaving the manufacturer. This allows our customers to benefit from repairs, replacement of parts and even replacements for free. What is covered: For how long: What we will do: Exclusions: All parts defective in material and workmanship. Three years from purchase date. Repair or replace any defective parts. Regular replacement parts such as air filter cartridges and UV lamp.
Canada sales@heavenfresh.ca www.heavenfresh.ca 1-866-625-1857 (English) 1-866-583-1857 (French) USA sales@heavenfresh.com www.heavenfresh.com 1-800-642-0367 UK sales@heavenfresh.co.uk www.heavenfresh.co.uk 0800 952 9962 Germany sales@heavenfresh.de www.heavenfresh.de 0800 66 47 259 France sales@heavenfresh.fr www.heavenfresh.fr 0800 900 991 Ireland sales@heavenfresh.ie www.heavenfresh.ie 1-800-550-457 Middle East sales@heavenfresh.ae www.heavenfresh.