Service Jacks Operating Instructions & Parts Manual Model Number HW93642 HW93652 Capacity 2 Ton 3 Ton Assembled in the US with US and Global Components ! This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153 customerservices@heinwerner-automotive.
SAFETY AND GENERAL INFORMATION Save these instructions. For your safety read, understand, and follow the information provided with and on this jack. The owner and operator of this equipment shall have an understanding of this jack and safe operating procedures before attempting to use. The owner and operator shall be aware that use and repair of this product may require special skills and knowledge.
! WARNING ! WARNING • Read, understand and follow the instructions before using the appliance. •The operating manual and safety information should be communicated in the native language of the operator before use. • Failure to do so may cuase personal injury and/ or property damage. • Study, understand, and follow all instructions before operating this device. • Do not exceed rated capacity. • Use only on hard, level surface. • Lifting device only.
OPERATION Lifting ! WARNING: Lift only on areas of the vehicle as specified by the vehicle manufacturer. 1. Follow the vehicle manufacturer’s recommended guidelines for lifting. Engage the emergency brake and chock each unlifted wheel in both directions to prevent inadvertent vehicle movement. 2. Locate and close the release valve by turning the handle clockwise until firm resistance is felt. 3. Refer to the vehicle manufacturer owner’s manual to locate approved lifting points on the vehicle.
MAINTENANCE NOTICE: Use only quality grade hydraulic jack oil. Avoid mixing different types of fluid and NEVER use brake fluid, turbine oil, transmission fluid, motor oil or glycerin. Improper fluid can cause failure of the jack and the potential for sudden and immediate loss of load. Hein-Werner hydraulic jack oil HW93291 or equivalent is recommended. Adding oil 1. Lower saddle fully. 2. Set jack in its upright, level position. 3. Locate and remove air vent screw. 4.
Replacement Parts Illustration for Model HW93642 & HW93652 (refer to parts list on page 7) Frame Section 5 1 4 2 6 3 14 7 13 8 9 10 12 11 Hydraulic Unit Cross Section 32 31 30 29 Handle Assembly 28 40 15 39 16 17 24 38 18 19 20 21 25 22 27 26 37 37 23 36 One-Piece Handle Hydraulic Unit Base 35 33 34 Figure 2 - Parts Illustration for Model HW93642 & HW93652 6
Replacement Parts List for Model HW93642 & HW93652 (refer to parts drawing on page 6) Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16* 17 18 19 20 21* 22* 23 24 25* 26* 27* 28* 29* 30* 31* 32 33* 34* 35* 36* 37* 38* 39* 40 * Part Number HW93642 HW93652 231583 201115 219451 231584 201806 201805 214557 204324 234678 234677 234956 239304 239312 221408 243618 N/A N/A N/A N/A N/A N/A N/A N/A N/A 890-021-666 230301 221318 221748 228256 218043 233917 216143 248731 203196 203198 203201 204842 201733 234957 234961 2487
TWO YEAR LIMITED WARRANTY For a period of two (2) years from date of purchase, SFA Companies will repair or replace, at its option, without charge, any of its products which fails due to a defect in material or workmanship under normal usage. This limited warranty is a consumer's exclusive remedy. Performance of any obligation under this warranty may be obtained by returning the warranted product, freight prepaid, to SFA Companies Warranty Service Department, 10939 N. Pomona Ave., Kansas City, MO 64153.
