Manual

ManualsBrandsHeli-Max ManualsAir equipmentHMXE0800

READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION.

IT CONTAINS IMPORTANT INSTRUCTIONS AND WARNINGS

CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.

Champaign, Illinois

(217) 398-8970

helihotline@hobbico.com

INSTRUCTION MANUAL

Rotor Span: 27.5 in [700mm]

Height: 9.3 in [236 mm]

Length: 24 in [610mm]

Weight: 18.4 oz [521g] no battery,

25 oz [708g] w/ﬂ ight battery (GPMP0520)

Motor: 420 Brushless out-runner motor

Radio: Futaba

6EX 6-channel 2.4GHz FASST transmitter

Futaba R606FS 6-channel 2.4GHz FASST receiver

Servos: Futaba S3114 micro HT servo

Gyro: Heli-Max

™

Heading Lock HM 4000 Gyro w/remote dual gain

™

• Never charge in excess of 4.20V per cell.

• If the battery should become damaged, discard the

battery. Do not attempt to use a damaged battery.

• Do not leave the charger unattended while charging.

Disconnect the battery and remove input power from the

charger immediately if either becomes hot! However, it is

normal for the charger to get warm.

• Disconnect the battery from the charger and carefully

move the battery to a ﬁ reproof location if the battery

begins to swell or smoke!

• Never charge at currents greater than 1C.

• Always charge in a ﬁ reproof location.

• Never trickle charge.

• Never allow the battery temperature to exceed 150° F

[65° C].

• Never disassemble or modify pack wiring in any way or

puncture cells.

• Never discharge below 2.5V per cell.

• Do not allow water, moisture or foreign objects into

the charger.

• Do not block the air intake holes, which could cause the

charger to overheat.

• Do not place the charger or any battery on a ﬂ ammable

surface or near a combustible material while in use.

• Do not charge on a carpet, cluttered workbench, paper,

plastic, vinyl, leather, wood, or inside an R/C model.

• Never charge inside a full sized vehicle.

• Always disconnect the battery from the charger and the

power supply from the charger when not in use.

• Do not attempt to charge a battery if it is swollen or hot.

• ALWAYS KEEP OUT OF REACH OF CHILDREN.

IMPORTANT PRECAUTIONS

WARNING!! Read the entire instruction sheet included with your battery and charger. Failure to follow all

instructions could cause permanent damage to the battery, charger or its surroundings, and cause bodily harm!

Summary of content (20 pages)

PAGE 1
™ Rotor Span: 27.5 in [700mm] Height: 9.3 in [236 mm] Length: 24 in [610mm] Weight: 18.4 oz [521g] no battery, 25 oz [708g] w/flight battery (GPMP0520) Motor: 420 Brushless out-runner motor Radio: Futaba® 6EX 6-channel 2.4GHz FASST transmitter Futaba R606FS 6-channel 2.
PAGE 2
,500 AMA chartered clubs across the country. Contact the AMA at the address or toll-free phone number below. TABLE OF CONTENTS Academy of Model Aeronautics 5151 East Memorial Drive Muncie, IN 47302 Tele: (800) 435-9262 Fax (765) 741-0057 Or via the Internet at: www.modelaircraft.org INTRODUCTION ............................................................... 2 AMA .................................................................................. 2 SAFETY PRECAUTIONS .....................................
PAGE 3
4. You must check the operation of the model before every flight to insure that all equipment is operating and that the model has remained structurally sound. Be sure to check linkages or other connectors often and replace them if they show any signs of wear or fatigue. Heli-Max Product Support: 3002 N. Apollo Drive, Suite 1 Champaign, IL 61822 Telephone: (217) 398-8970, ext. 5 Fax: (217) 398-7721 E-mail: helihotline@hobbico.com 5.
PAGE 4
KIT CONTENTS 2 1 1. Transmitter 2. Helicopter OPERATIONAL WARNINGS which will reduce the power output to safe levels when the safe operating temperatures have been exceeded. If this has occurred please allow the model 10 minutes to cool down. CAUTION! A separate Battery Eliminator Circuit (BEC) must be used if you decide to change the stock (Futaba® S3114) servos to some other type of analog or digital servos. We highly recommend the Castle Creations CC BEC 10A Switching Regulator (CSEM0005).
PAGE 5
ELECTRIC MOTOR WARNING The Dual Rate Switch changes the control rate of the helicopter. The High Rate provides the maximum control which is necessary for 3D flight and aerobatics. The low rate reduces control throw which makes the model easier to fly. The low rate is recommended for your first flight. Once you have become accustomed to the AXE 400 3D RTF please feel free to use high rate if you prefer.
PAGE 6
LEFT CYCLIC The Idle-Up function is disabled within the transmitter for safety. If you are beginning aerobatics or are an experienced pilot and feel you have a need for the Idle Up function, then please follow the instructions on page 11 to enable this function. Moving the cyclic stick left will cause the helicopter to tilt left and start moving in that direction. AFT CYCLIC Moving the cyclic stick backwards (towards you) will cause the helicopter to tilt backwards and start moving that direction.
PAGE 7
INCREASING THROTTLE & COLLECTIVE PITCH - CLIMB TAIL ROTOR RIGHT Moving the collective stick forward (away from you) will cause the helicopter to climb higher. Moving the tail rotor stick right will cause the helicopter nose to move right (clockwise). DECREASING THROTTLE & COLLECTIVE PITCH DESCEND GET THE MODEL READY TO FLY INSTALL BATTERIES IN THE TRANSMITTER Remove the battery cover from the back of the transmitter and install eight “AA” batteries into the transmitter.
PAGE 8
MIX WARNING In the following step do not connect the flight battery to the ESC until you are instructed to do so. With the power lead facing downward, place the flight battery onto the battery tray and attach using the battery strap as shown. If the transmitter is turned on with the Throttle Hold or Idle Up function switched on, the screen will show "MIX" and a warning will sound. Please turn the Throttle Hold and Idle Up functions off to continue.
PAGE 9
CONNECTING THE FLIGHT BATTERY TRACKING THE MAIN BLADES WARNING! Always wear safety glasses when operating this model or Tracking the Main Blades. Before connecting the flight battery verify that the Idle Up Switch and Throttle Hold switches are off and verify that the throttle stick is in the lowest position. Warning! Once the flight battery has been connected the helicopter will have full power available.
PAGE 10
the blades are the same. If they are not, adjust one of the linkages to bring the blades into the same plane. to nose-in hovering, and try to lengthen the delay between transitions. This will allow you to practice nose-in and still give you a chance to get out of trouble. As you improve you’ll remain nose-in for longer periods of time. TAKEOFF During your first flight it is important to have light winds and an assistant to keep an eye on things around you.
PAGE 11
periods of time. As you become accustomed to the reversed controls, you will extend the time inverted. It is very difficult and will take some practice. Also, make sure you have plenty of altitude for recovery if needed. QUICK REFERENCE TO TRANSMITTER FUNCTIONS ACTIVATING THE IDLE UP FUNCTION Please refer to the included manufacturer’s instruction manual for complete details for each function. The initial set up of the transmitter suits a beginner modeler.
PAGE 12
LINKAGE ROD LENGTHS ORDERING PARTS Replacement parts for the Heli-Max AXE 400 3D RTF are available using the order numbers in the Parts List on page 18. The fastest, most economical service can be provided by your hobby dealer. To locate a hobby dealer, visit the Hobbico web site at www.hobbico.com. Choose “Where to Buy” at the bottom of the menu on the left side of the page. Follow the instructions provided on the page to locate a U.S., Canadian or International dealer.
PAGE 13
23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 OPTIONAL PARTS HMXE8501 .... Swashplate ........................................1 HMXE8512 .... Mixing Arms .....................................16 HMXE8502 .... Washout Base ...................................1 HMXE8503 .... Main Shaft .........................................1 HMXE8504 .... Seesaw Bushing Set .........................2 HMXE8505 .... Spindle Bolt Set ...................
PAGE 14
EXPLODED VIEWS MAIN FRAME 22 21 20 18 13 19 18 17 16 15 14 17 15 13 5 3 Screw Set 11 12 10 9 8 7 7 4 61 2 6 1 3 2 3 2 2 1 2 14
PAGE 15
TAIL BOOM ASSEMBLY 59 57 24 29 58 29 57 29 58 24 24 57 24 59 55 56 32 54 32 53 3 53 3 52 50 21 52 41 51 3 48 49 43 3 47 44 3 46 62 60 29 35 45 34 33 32 33 32 28 32 30 24 23 22 27 26 24 38 39 22 60 41 38 25 24 24 42 3 15 28 29 7 35 37 29 ROTOR HEAD 32 31 36 31 29 30 22 40
PAGE 16
Blade Grip Bolt Set Part #HMXE8506 EVPL #29 1Set Main Blade Grip Set Part #HMXE8507 EVPL #30 Head Dampeners Part #HMXE8509 EVPL #33 4Pcs Feathering Spindle Part #HMXE8510 EVPL #34 Seesaw Part #HMXE8513 EVPL #37 1Pc Control Ball Set Part #HMXE8517 EVPL #41 Dampening Shim Set Part #HMXE8508 EVPL #31 1Set Bearings Main Grips/Tail Shaft Part #HMXE8827 6Pcs EVPL #31 1Pc Head Block Part #HMXE8511 EVPL #35 1Set Mixing Arms Part #HMXE8512 EVPL #36 2Pcs Flybar Control Set Part #HMXE8514 EVPL #38 1S
PAGE 17
PAGE 18
Tail Rotor Hub Part #HMXE8648 EVPL #57 1Set Tail Rotor Grips Part #HMXE8649 EVPL #58 1Pc Tail Rotor Blades Part #HMXE8426 EVPL #59 ESC Part #HMXM2009 EVPL #61 1Pc Tail Rotor Drive Belt Part #HMXM2009 EVPL #61 1Pc Main Rotor Gear 1Pc Without One-Way Bearing Part #HMXM8029 EVPL #12 1Pc Main Rotor Blades Part #HMXM8323 EVPL #60 OPTIONAL PARTS CNC Main Blade Grips (2 Pcs) Part # HMXE7482 CNC Head Block (1 Pc) Part # HMXE7483 CNC Flybar Carrier (1 Pc) Part # HMXE7484 CNC Washout Arms (2 Pcs) Part
PAGE 19
CNC Swashplate (1 Pc) Part # HMXE7488 CNC Tail Case (1 Pc) Part # HMXE7489 CNC Tail Drive Belt Pulley (1 Pc) Part # HMXE7490 CNC Counter Drive Belt Pulley (1 Pc) Part # HMXE7491 CNC Tail Blade Grips (2 Pcs) Part # HMXE7492 CNC Mixer Arms (2 Pcs) Part # HMXE7493 CNC Tail Servo Mount (2 Pcs) Part # HMXE7494 CNC Boom Support Ends (2 Pcs) Part # HMXE7495 CNC Boom and Fin Clamp (1 Pc) Part # HMXE7496 Carbon Fiber Vertical Fin (1 Pc) Part # HMXE7498 Carbon Fiber Horizontal Fin (1 Pc) Part # HMXE7499 19