® 1Si Quadcopter Instruction Manual WARNING Please fully read and understand this manual and the operation and all safety aspects required of you for the safe operation of this product. Before use, if you feel this product is not for you please return it to your place of purchase. Heli-Max products are to be used by ages 14 and over. Manual Specifications and Description Changes The instruction manual, warranties and other associated documentation is subject to change without notice.
® INTRODUCTION Thank you for purchasing the Heli-Max 1Si Quadcopter. We are certain you will get many hours of enjoyment out of this model. If you should have any questions or concerns please feel free to contact us at: helihotline@hobbico. com. For the latest technical updates or manual corrections visit the Heli-Max web site at www.helimax-rc.com. If there is any new technical information, changes or important updates to this model a “tech notice” box will appear on the 1Si product page.
® WARRANTY SERVICE Heli-Max guarantees this kit to be free from defects in both material and workmanship at the date of purchase. This warranty does not cover any component parts damaged by use or modification. In no case shall HeliMax’s liability exceed the original cost of the purchased kit. Further, Heli-Max reserves the right to change or modify this warranty without notice.
® FEATURES & SPECIFICATIONS Features ● ● ● ● ● ● ● ● ● Switchable TAGS-FX™ Sensor Fusion stabilization system On board micro digital video camera (HMXE0832 only) On board micro snap-shot digital picture camera (HMXE0832 only) USB MicroSD Card reader (HMXE0832 only) 2G MicroSD removable card (HMXE0832 only) LEDs for orientation built into frame Actual Direction Control flight mode Auto Return function Optional rotor blade guards Product Specifications Size: 125 mm (4.
away from the rotors. The spinning blades of a model of this type can cause serious injury. ● When choosing a flying site stay clear of buildings, trees and power lines. AVOID flying in or near crowded areas. ● DO NOT fly close to people or pets. Maintain a safe distance from the quadcopter. ● Do not alter or modify the model. Doing so may result in an unsafe or unflyable model.
Charge Warnings ● Only use the included charger with the included LiPo battery. Do not attempt to use the provided charger with NiCd, NiMH or batteries with other chemistries. ● Do not leave the charger unattended while in use and always charge your battery in a fire-resistant location. ● Disconnect the battery and remove input power from the charger immediately if either becomes hot! ● Do not allow water or other foreign objects to enter the charger.
Transmitter Setup ❏ Install 4 AA batteries in the t r a n s m i t t e r b y re m o v i n g t h e battery cover from the back of the transmitter. Double-check the polarity of each battery before replacing the battery cover. ❏ Turn the Transmitter on and make sure that there is a blue light behind the Heli-Max panel at the top of the transmitter. The LCD screen should be on, with a throttle position indicator and other information. ❏ Make sure the electronic trim indicators on the display are centered.
® INSTALLING THE BLADE GUARDS Installing the optional rotor blade guards is recommended. Besides protecting the rotor blades from damage, these parts can also allow the 1Si to continue to fly if it brushes up against a wall or other solid object.
❏ Slide the guard over the motor and position the hole for the mounting screw over the dimple on the top of the arm. ❏ Secure the guard to the frame with the included screw. ® FLYING YOUR 1Si QUADCOPTER Electric motors are very dangerous. Do not work on the model while the flight battery is plugged in as interference may cause the main rotor blades to spin, possibly causing injury. Turn on the transmitter and lay it down so the antenna is pointed at the LED on the back of the 1Si as shown in the photo.
Hovering Once the quad is in the air simply try to keep it in one spot. This will take some practice. Remember that even a light breeze will have an effect on the stability of the quad. Landing Level the quad into a steady hover and slowly decrease power until it lands. You might notice as the Quadcopter is ready to touch down it moves around a little. This is normal as the Quadcopter enters ground effect.
If the model is to be stored for a long time period, please remove the batteries from the transmitter to avoid damage to the contacts. If storing the model for several weeks, the batteries for the quadcopter should be charged to 50% of a full charge and checked after 3 to 4 months. ® FLIGHT MODE OPTIONS Dual Rate The TX465 transmitter has a dual rate function.
To return to the normal flight mode, press the “F Mode” button again. The rear LED will flash twice, stay on for a second, flash twice again, and then remain steady. This sequence indicates that the accelerometers and the Braking function are active again. Actual Direction Control When the “ICM” button on the upper left corner of the transmitter is pressed for at least 3 seconds, the 1Si will enter the “Actual Direction Control” flight mode and the LED on the back of quadcopter will flash slowly.
This procedure should be used if the return speed of the 1Si needs to be changed. 1. Enter the Adjustment Mode as described earlier. 2. Push the rudder trim button to the left increase the return speed. The longer the button is held to the left, the LED on the 1Si will flash faster and the tone will increase in pitch to indicate that a higher return speed is being selected. When the LED remains steady, the highest speed has been selected. Moving the button to the right will reduce the return speed.
on the card again and the inner spring system will help eject the card. Note: The card must be in place to capture video or Pictures. The camera has no internal memory. Downloading the video and pictures from the camera: Install the MicroSD card into the reader. Plug the reader into the USB port of your computer. The USB connection will be auto recognized and the files ready to be transferred. At this point you can copy or transfer your files to your folder structure.
Control Board Sensor Calibration 1. Enter the Adjustment Mode as described on page 12. 2. Press up on the throttle trim button and the rear LED on the 1Si will start flashing rapidly. 3. When the LED stops flashing, press down on the left stick to exit. If you still have problems, try the tip on page 17. Transmitter Calibration Press on the ICM button while turning on the transmitter. The display will show a “1” briefly then display a “2”.
Hold the transmitter by the upper right corner and lower left corner so the antenna is pointed 45 degrees to the right. Rotate the transmitter three times with the antenna moving toward you, then three more times in the opposite direction. Put the transmitter down with the antenna pointed away from you and push the ICM button. The display should read “0”. Press the F Mode button. The display will indicate 90 and the transmitter should be rotated so the antenna is at 90 degrees.
Solution 3: Make sure card is OK by putting the card in reader and checking on your PC. PROBLEM: 1Si drifts while hovering. Solution: Use the following procedure to re-calibrate the neutral setting on the 1Si. 1. Enter the Adjustment mode as described on page 12. 2. The quadcopter should be hovered about 3 feet above the floor in a calm area without any wind or drafts. Release both sticks for a second or two and observe the 1Si’s behavior.
® REPLACEMENT PARTS Key 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Part No. Description HMXE2203 HMXE2202 HMXE2244 HMXM2053 HMXE2241 HMXE2240 HMXE2243 HMXE2242 HMXE2180 HMXE2245 HMXP1015 HMXZ0001 HMXE7339 HMXE2246 HMXJ2029 HMXP2023 HMXZ0002 Blade Guard (4) Rotor Blades Black / White Body / Frame Gray TAGS-FX Controller Board Motor/LED Right Front CCW 1Si Motor/LED Left Front CW 1Si Motor/LED Right Rear CW 1Si Motor/LED Left Rear CCW 1Si Control Board Dampeners Receiver Mount LiPo 1S 3.
® EXPLODED VIEW 13 1 1 2 2 13 3 4 7 9 13 5 10 8 6 11 12 3 13 14 19
® Entire Contents © 2013 Hobbico®, Inc.
