User manual Dominus 10SC V2

ManualsBrandsHelion ManualsBuggy - Truggy - All Terrain RCDominus 10SC V2

ENGLISH-US

OWNER’S MANUAL

• Before using your product, review all documentation and inspect the products carefully. If for some reason you decide it is not

what you wanted, then do not continue with unpacking, setup or operation of your product. Your local hobby dealer cannot ac-

cept a product for return or exchange after partaking in actions that produce wear and tear.

• Read, understand and follow all instructions and accompanying material carefully before operating or assembling your vehicle

to prevent serious damage to your vehicle. Failure to complete these tasks properly or intentional aversion to the content will be

considered abuse and/or neglect.

• Product speciﬁcations are subject to change without notice. Due to ongoing development, the actual product may vary from

images shown.

• This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

• This product is not a toy! (14+) Recommended for ages 14 and up. Adult supervision required for ages under 18 years old.

Contains small parts, keep out of reach of children 3 years of age and younger.

Now compatible with IKONNIK Xenon protocol systems

LENGTH 540mm (21.26in)

WIDTH 290mm (11.42in)

HEIGHT 215mm (8.46in)

WHEELBASE 327mm (12.87in)

WHEEL DIAMETER O: 55.5mm (2.18in) x I: 76mm (2.99in) x W: 38.6mm (1.52in)

WHEEL OFFSET 12mm Hex, TRX/KYO Compatible

WEIGHT* 2523g (5lb-9oz)

BATTERY 3,000mAh NiMH 7-CELL, 8.4V, HCT-Plug

MOTOR Brushless 3,000kV Reaktor4 4-Pole Sensorless

RADIO IKONNIK Xenon (Xe) HRS3.2 2.4GHz 3-CHANNEL

CHARGER AC 1Amp

*APPROXIMATE OUT-OF-THE-BOX WEIGHT

Scan this QR code

with your smart

phone to view the

getting started video

for this product.

Summary of content (24 pages)

PAGE 1
ENGLISH-US OWNER’S MANUAL LENGTH 540mm (21.26in) WIDTH 290mm (11.42in) HEIGHT 215mm (8.46in) WHEELBASE 327mm (12.87in) WHEEL DIAMETER O: 55.5mm (2.18in) x I: 76mm (2.99in) x W: 38.6mm (1.52in) WHEEL OFFSET 12mm Hex, TRX/KYO Compatible WEIGHT* 2523g (5lb-9oz) BATTERY 3,000mAh NiMH 7-CELL, 8.4V, HCT-Plug MOTOR Brushless 3,000kV Reaktor4 4-Pole Sensorless RADIO IKONNIK Xenon (Xe) HRS3.2 2.
PAGE 2
NOTICE! Although your Helion RC product is adjusted and tested at the factory prior to final packaging, some issues may arise during shipping and handling that can be easily resolved at home. For other issues it should be known that hobby grade radio controlled products such as those offered by Helion RC differ from toy grade, in that they are intended to be user-servicable products where the user can disassemble and maintain their own product using factory replacement parts.
PAGE 3
1/10th SCALE 4x4 ELECTRIC SHORT COURSE TRUCK GETTING STARTED 1. Remove the body and battery from vehicle to prepare for charging. a. Remove the battery from the vehicle by loosening the hook-and-loop straps. b. Read charging instructions and understand all warnings and cautions before proceeding. This product is not a toy and should not be charged, operated, or maintained without supervision of an adult. c.
PAGE 4
PRECAUTIONS WHEN USING RADIO CONTROLLED PRODUCTS • Your model can cause serious damage or injury so please use caution and courtesy when operating your model. • Do not expose the radio system to water or excessive moisture. • As a safety precaution, perform all transmitter and receiver adjustments with the vehicle’s wheels off the ground. This ensures the complete control over the vehicle at all times during adjustments.
PAGE 5
1/10th SCALE 4x4 ELECTRIC SHORT COURSE TRUCK IKONNIK XENON HRS3.2 PROTOCOL, PAIRING AND FAIL SAFE SETTING Understanding Protocol and Pairing the Transmitter and Receiver: The process of allowing communication to occur between a 2.4GHz transmitter and receiver is called “pairing” (sometimes referred to as “matching” or “binding”). The “language” used to communicate between the transmitter and the receiver is called the “protocol”.
PAGE 6
IKONNIK XENON HRS3.2 CONNECTION AND CONFIGURATION... Digital Trim Settings: • Steering Trim ›› Press the “ST+” or “ST-“ button to adjust the neutral position of the steering. A long “beep” will sound ›› Once the trim setting reaches the limit, a long steady “beep” will sound »» Depending on your servo configuration, “ST+” or “ST-“ will move the servo either left or right.
PAGE 7
1/10th SCALE 4x4 ELECTRIC SHORT COURSE TRUCK ...IKONNIK XENON HRS3.2 CONFIGURATION CONTINUED Factory Reset • The transmitter has a two stage factory reset. ›› Model Reset: Resets the settings . »» Use a small toothpick to press the Reset button (above the LED) and power ON the Transmitter. »» Continue holding for 5 seconds until you hear a beep sound, then release the button. ›› Factory Reset: resets all pareameters to the factory settings.
PAGE 8
IKONNIK XENON HRS3.2 STANDARD OPERATION ›› From pulled back: the vehicle will apply brakes to slow the speed. »» A second push forward of the trigger will apply brakes again. »» A second push forward on the trigger will apply reverse throttle. »» WARNING: Causing the vehicle to make quick transitions from forward/reverse motion to the opposite direction using the throttle control can cause damage to your vehicle and electronics and will void the warranty. Using your transmitter for the first time: 1.
PAGE 9
1/10th SCALE 4x4 ELECTRIC SHORT COURSE TRUCK ...RADIENT REAKTOR BRUSHLESS SYSTEM OVERVIEW CONTINUED Your ESC has been pre-installed at the factory but before using your vehicle each time it is good to double check the wiring for damage or loose connections to ensure everything is in working order before use. Refere to the diagram below to check the connections of your electronics system. Some brushless motors such as the Reaktor included with your vehicle use only black wires, this is okay.
PAGE 10
... CALIBRATING AND PROGRAMMING YOUR ESC CONTINUED Programming your ESC: The Radient Reaktor is a programmable ESC. Although the default settings should work well for most users, these settings exist so that you can fine tune the performance of your ESC to your experience and components.
PAGE 11
1/10th SCALE 4x4 ELECTRIC SHORT COURSE TRUCK ...PROTECTION MODES AND ERROR CODES CONTINUED the surface. You will typically want a lower punch setting when the surface has less traction. To get the optimal performance out of LiPo batteries, on high traction sufaces, setting 4 is recommended. 1. Level 1 (70%): This setting will provide the smoothest throttle feel and least wheel spin. 2. Level 2 (80%) 3.
PAGE 12
...REAKTOR ESC PROGRAMMING TREE AND PARAMETERS Use the tabel below to better understand the programming process. This should help you navigate thorugh the programming menu.
PAGE 13
1/10th SCALE 4x4 ELECTRIC SHORT COURSE TRUCK REAKTOR SYSTEM TROUBLESHOOTING Problem / Symptom ESC will not set to transmitter After turning ON, the motor won’t work and no sound comes from motor After turning ON the ESC, the motor won’t operate normally but instead gives a beep-beep, beep-beep alert tone with 1 second interval of each beepbeep After turning ON the ESC the motor won’t operate normally but instead gives a beep-, beep-, beepalert tone with each beephaving an interval of one second Car slowed
PAGE 14
ADJUSTING AND TUNING YOUR VEHICLE The Dominus 10SCv2 has been engineered with some available tuning options listed here for reference. The default configuration has been chosen to provide what we feel is the most enjoyable experience for most operating conditions.
PAGE 15
1/10th SCALE 4x4 ELECTRIC SHORT COURSE TRUCK ...GENERAL CARE AND MAINTENANCE CONTINUED... ii. Check how much movement is allowed (backlash) of the spur gear before the pinion gear moves (this is mostly feel, not visual). Check this movement in multiple places by rotating the spur gear approximately 1/6 rotation and rechecking. iii. If the spur gear is allowed to move more than a very small amount, or if it there is no backlash, the gear mesh must be adjusted.
PAGE 16
...GENERAL CARE AND MAINTENANCE CONTINUED Caution: Be sure to use extreme care when using hobby-grade CA glue. It is specially formulated to cure quickly and create a strong bond. It will bond skin and can cause injury if used improperly. Follow manufacturer’s warnings and directions when using CA glue. It is always recommended to wear eye protection when maintaining your vehicle. ii. When reinstalling tires, use caution when tightening the nuts that secure the wheels to the vehicle.
PAGE 17
1/10th SCALE 4x4 ELECTRIC SHORT COURSE TRUCK TROUBLESHOOTING GUIDE Problem / Symptom Vehicle will not turn on Transmitter will not turn on Short radio range (Vehicle stops responding to transmitter at short distances) Steering not responding as expected Possible Cause Battery voltage too low Battery not connected Damaged battery Battery voltage too low Battery/ies installed improperly Damaged or improperly installed receiver and antenna Receiver is malfunctioning Battery voltage too low Trim not set prope
PAGE 18
FRONT SUSPENSION ASSEMBLY...
PAGE 19
1/10th SCALE 4x4 ELECTRIC SHORT COURSE TRUCK CHASSIS ASSEMBLY...
PAGE 20
REAR SUSPENSION ASSEMBLY...
PAGE 21
1/10th SCALE 4x4 ELECTRIC SHORT COURSE TRUCK TRANSMISSION ASSEMBLY...
PAGE 22
SAFETY TIPS Although great for first time users, Helion RC products are indeed advanced radio controlled vehicles with sensitive electronics and moving parts capable of causing injury if used improperly. Always use caution and common sense as failure to operate your Helion RC product in a safe and responsible manner can result in damage to the product or other properties. Therefore this product is not intended for use or maintenance by children without direct adult supervision.
PAGE 23
1/10th SCALE 4x4 ELECTRIC SHORT COURSE TRUCK ...REPLACEMENT PARTS LIST CONTINUED HLNA0200...Diff, Complete, 10-34 (DSC2, TR, IMT)................... HLNA0201...Gear Set, Diff, 10-34 (DSC2, TR, IMT)..................... HLNA0228...Serrated Nuts, Flanged, M4x0.7x7mm................... HLNA0231...Slipper Clutch Pads (10-US)................................... HLNA0232...Slipper Spring And Nut (10-US).............................. HLNA0233...Slipper Clutch Plates And Pads (10-US)................. HLNA0246...
PAGE 24
POWERED BY 000172-004 (REV A) HLNA0445