User manual Conquest 10B XLR 2WD Buggy Brushless Helion-RC

ManualsBrandsHelion ManualsHobbyConquest 10B XLR 2WD Helion-RC Brushless Buggy

QUICK-START GUIDE

Full manual available to download from: www.Helion-RC.comFull manual available to download from: www.Helion-RC.com

Quick-Start

Guide

Product specications are subject to change without notice.

Due to ongoing development, the actual product may vary from

images shown.

This product contains chemicals known to the State of California

to cause cancer, birth defects and other reproductive harm.

This product is not a toy! (14+) Recommended for ages 14 and

up. Adult supervision required for ages under 18 years old.

Contains small parts, keep out of reach of children 3 years of

age and younger.

To download the full Owner’s Manual & Technical

Information Guide, please visit:

www.Helion-RC.com

or scan the QR code with your smart phone.

Distributed in the

UK by:

J Perkins Distribution Ltd,

Lenham,

Kent, UK

ME17 2DL.

www.jperkins.com

Distributed in Australia by:

Model Engines (Aust.) Pty. Ltd.,

P.O. BOX 828

NOBLE PARK 3174

Australia

www.modelengines.com.au

Ph (03) 8793 5555

warranties@modelengines.com.au

Distributed in the US by:

Firelands Customer Service/Product Support

1133 Libra Drive, Lincoln, NE 68512

www.relandsgroup.com

1-800-205-6773

customerservice@relandsgroup.com

HLNA0761 Conquest 10B XLR (US)

HLNA0771 Conquest 10B XLR (UK-EU)

HLNA0781 Conquest 10B XLR (AU)

MADE IN CHINA

Summary of content (8 pages)

PAGE 1
Quick-Start Guide Product specifications are subject to change without notice. Due to ongoing development, the actual product may vary from images shown. This product contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. HLNA0761 Conquest 10B XLR (US) HLNA0771 Conquest 10B XLR (UK-EU) HLNA0781 Conquest 10B XLR (AU) This product is not a toy! (14+) Recommended for ages 14 and up. Adult supervision required for ages under 18 years old.
PAGE 2
QUICK-START GUIDE 1 Remove the components from the box and ensure the contents are correct: • 1 x Conquest 2WD Buggy • 1 x 2000mAh 6-cell NiMH battery pack • 1 x IKONNIK ET3 2.4GHz 3-channel transmitter • 1 x 6-cell wall charger • 1 x Quick-Start Guide. 2 Remove the two body clips from the car and lift the body clear. 3 Locate the battery cradle in the centre of the car, release the hook and loop tape and withdraw the battery pack.
PAGE 3
5 Re-insert the fully charged battery pack into the cradle and tightly secure it with the hook and loop straps. 6 Remove the battery cover from the underside of the ET3 transmitter and insert four AA alkaline cells. Take care to ensure that the correct polarity is observed. 7 Ensure the radio switch is in the OFF position, then connect the battery to the ESC. 8 Replace the body and secure it with the two body clips.
PAGE 4
QUICK-START GUIDE 10 Locate the switch and turn ON your Conquest. In the unlikely event that the car does not operate, see the PAIRING / BINDING instructions at the back of this guide 11 Check the operation of the throttle and steering. Pulling the throttle trigger back will drive the car forward, pushing the trigger forward once will apply the brakes while pushing the trigger forward twice will drive the car in reverse. Turning the wheel to the right will cause the car to turn right and vice versa.
PAGE 5
Pairing / Binding The Transmitter Having followed steps 1 to 10, in the unlikely event that your car does not operate please follow the 5 stage pairing process detailed here. 1 Remove the body and locate the ET3 Krypton receiver. 2 Place your Conquest and ET3 transmitter in close proximity but not less than 12” (300mm) apart. 3 Press and hold the PAIR / BIND button on the receiver then switch the receiver on. The receiver’s LED will flash to indicate that it is in PAIR / BIND mode.
PAGE 6
REPLACEMENT PARTS Replacement Parts HLNA0970.......... Rear Chassis Plate, B, ST, MT HLNA0971.......... R-Clip, B, ST, MT HLNA0972.......... Nuts(M4) HLNA0973.......... M3*8 Column Head Hex Screw HLNA0974.......... Wheel Hex HLNA0975.......... Nuts(M3) HLNA0976.......... Radio Tray Mount HLNA0978.......... Back Shock HLNA0979.......... Shock Ball Head C HLNA0980.......... Pin 2*10 HLNA0981.......... Diff Planetary Gear HLNA0982.......... Diff Shaft HLNA0983.......... Differential Outdrive HLNA0984..........
PAGE 7
HLNA1015.......... Front Upper Link 58.5mm HLNA1016.......... Steering Link 55mm HLNA1017.......... Rear Upper Link 73mm HLNA1018.......... Servo Link 30.5mm HLNA1019.......... Gear Box HLNA1020.......... Motor Guard, B, ST HLNA1021.......... Main Gear Cover HLNA1022.......... Differential Case(48P) HLNA1023.......... Gear (34T-48P) HLNA1024.......... Gear (81T-48P) HLNA1025.......... Wing Mount, B HLNA1026.......... Front Shock Absorber HLNA1027.......... Rear Arm Bulkhead HLNA1028..........
PAGE 8
REPLACEMENT PARTS HLNA1055.......... Rear Lower Suspension Arm Screws 3*29mm HLNA1056.......... Pin 3*26 HLNA1057.......... Pin 5*18 HLNA1059.......... Powder Steel Gear(20T-48P) HLNA1061.......... Rear Shock Absorber HLNA1070.......... Cap Head Hex. Mechnical Screw 3*14 HLNA1071........... Cap Head Hex. Mechnical Screw 3*16 HLNA1072.......... M3*3 Grub Hex Screws HLNA1077B........ Replacement Body, B Blue HLNA1077R........ Replacement Body, B Red HLNA1077Y........ Replacement Body, B Yellow HLNA1077G......