User's Guide

LED
State Meaning
Power Green
(during the boot the LED is red)
Unit is powered and operating normally
Flashing in sync with another LED
Error on the port indicated
Flashing independently after boot up
period
Internal error
Off No mains power or product failure
LAN
On LAN connection available
Flashing (regular pattern) in sync
with POWER LED
Error on the LAN port
Flashing (irregular) Data transfer
Off
No LAN connection available
WIFI On WiFi connection available
Flashing (regular pattern) in sync
with POWER LED
Error on WiFi port
Flashing (irregular) WiFi data transfer
Off No WiFi connection available
WAN
On
WAN connection available
Flashing (regular pattern) in sync
with POWER LED
Error on WAN port
Flashing (irregular)
WAN data transfer
Off No WAN connection available
Signal
Red Cellular signal strength WEAK
Orange Cellular signal strength MEDIUM
Green Cellular signal strength STRONG
Off No cellular service available
This product contains Lithium coin type batteries. Batteries must only be
replaced by manufacturer authorised personnel. This ensures fitting of an
approved part and avoids the warranty being made void. Additionally it
ensures full compliance with Battery Directive 91/157/EEC & local legislation
regarding responsible recycling and disposal is adhered to.
In accordance with EU directive 2012/19/EC regarding Waste Electrical and
Electronic Equipment (WEEE), ensure that at end-of-life you separate this
product and its accessories from other waste and scrap and deliver to the
WEEE collection system in your country for recycling.
The Hera600 receives and transmits radio frequency energy while switched
on. Remember that interference can occur if it is used close to TV sets,
radios, computers or inadequately shielded equipment.
Follow any special regulations and never install your Hera600 wherever
forbidden or when you suspect that it may cause interference or danger.
As with any electrical equipment, you should not operate your Hera600 in the
presence of flammable gases, fumes or potentially explosive atmospheres.
Radio devices should not be used anywhere that blasting operations are
taking place.
GSM equipment such as the Hera600 must NOT be operated on aircraft. The
operation of wireless appliances in an aircraft is forbidden to prevent
interference with communications systems. Failure to observe these
instructions may lead to the suspension or denial of cellular services to the
offender, legal action, or both.
When in a hospital or a health care facility, observe the restrictions on the
use of mobile phones. Do not install the Hera600 in sensitive areas, such as
areas where the use of mobile phones are prohibited. Medical equipment
may be sensitive to RF energy.
The Hera600 incorporates a GSM radio module. Users should ensure that the
antenna is positioned at least 1 metre away from themselves and other
people in normal operation.
A clear visible warning should be posted informing people with implants of
the potential threat.
The operation of cardiac pacemakers, other implanted medical equipment
and hearing aids can be affected by interference from cellular terminals such
as the Hera600 when placed close to the device. Testing of the Hera600's
affect on implanted equipment should be carried out in advance of any
installations where interference is likely to occur.
The Hera600 operates using radio signals and cellular networks, and cannot
be guaranteed to connect in all possible conditions. Therefore, you should
never rely solely upon any wireless device for life critical communications.
SOS
Warnings:
Installation:
DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY
We, Eseye Design Limited declare under our sole responsibility that this device (H604v5)
complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
Caution: Exposure to Radio Frequency Radiation.
The device shall be used in such a manner that the potential for human contact during
normal operation is minimized. When connecting an external antenna to the device, the
antenna shall be placed in such a manner to minimize the potential for human contact during
normal operation. This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
This radio transmitter (11329A-H604V4) has been approved by Industry Canada to operate
with the antenna types listed below with the maximum permissible gain and required antenna
The operation of the device in the band 5150–5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems. This equipment
complies with ISED RSS 102 radiation exposure limits set forth for an uncontrolled
environment.
Modifications
Ÿ Reorient or relocate the receiving antenna.
Ÿ Consult the dealer or an experienced radio/TV technician for help.
The FCC requires the user to be notified that any changes or modifications to this device that
are not expressly approved by Eseye Design Limited may void the user's authority to operate
the equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of
20cm between the radiator and your body.
This device complies with ISED's licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) This device may not cause interference; and (2) This device
must accept any interference, including interference that may cause undesired operation of
the device
The antenna(s) used for this transmitter must be installed to provide a separation distance of
at least 20 cm from all persons and must not be co-located or operating in conjunction with
any other antenna or transmitter except in accordance with FCC multi-transmitter product
guidelines.
WLAN (UNII 1 and 3) - CORTEC P/N AN2450-5505BRS: 2.0dBi
impedance for each antenna type indicated. Antenna types not included in this list, having a
gain greater than the maximum gain indicated for that type, are strictly prohibited for use with
this device
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a non-residential installation. This equipment
generates, uses, and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try and correct
the interference by one or more of the following measures:
Ÿ Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
Ÿ Increase the distance between the equipment and the receiver.
Cellular: Gantetech GA-GSM-06: 3.5dBi
WLAN (UNII 1 and 3) - CORTEC P/N AN2450-5505BRS: 2.0dBi
This equipment is installed to be operated with a minimum 20cm distance between the
antenna and the user. Please note that high-power radars are allocated as primary users (i.e.
priority users) of the bands 5250- 5350 MHz and 5650-5850 MHz and these radars can
cause interference and/or damage to LELAN (License Exempt Local Area Network) devices.
Cet appareil est conforme au(x) standard(s) RSS exempts de licence d'Industrie Canada. Son
exploitation est soumise aux deux conditions suivantes : (1) cet appareil ne doit pas
occasionner d'interférence et (2) cet appareil doit supporter toutes les interférences, y
compris celles qui pourraient provoquer un mauvais fonctionnement de cet appareil.
Le présent émetteur radio (11329A-H604V4) a été approuvé par Industrie Canada pour
fonctionner avec les types d'antenne énumérés cidessous et ayant un gain admissible
maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus
dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement
interdits pour l'exploitation de l'émetteur.
Cet appareil doit être installé et utilisé avec une distance minimale de 20 cm entre l'antenne
et le corps de l'utilisateur. Veuillez noter que les radars haute puissance sont définis comme
utilisateurs principaux (i.e. utilisateurs prioritaires) des bandes 5250- 5350 MHz et 5650-5850
MHz, et que ces radars peuvent causer des interférences et/ou endommager les appareils
LE-LAN (réseau local exempt de licence).
Cellular: Gantetech GA-GSM-06: 3.5dBi
L'utilisation de l'appareil dans la bande de fréquences 5150-5250 MHz est uniquement
valable en intérieur pour réduire le risque de brouillage nuisible au fonctionnement des
systèmes mobiles par satellite partageant les mêmes canaux. Cet appareil est conforme aux
limitations de la norme IC RSS-102 concernant l'exposition aux radiations dans un
environnement non contrôlé.
Front Panel Indicators:
Ÿ Do not enclose the device within an unventilated housing where heat
may accumulate.
Ÿ Use only the mains power adaptor provided. Do not modify in any
way. Use of this product with any other mains power adaptor may
damage the unit will invalidate its warranty and may invalidate its
regulatory approval.
Ÿ There are no user-serviceable components inside the Hera600. If a
fault develops with the product, please contact your service provider
or reseller. The casing is fitted with a tamper indicator and should
NOT be opened under any circumstances as it will invalidate the
warranty.
Ÿ Ensure all warnings on this sheet are read and understood when
choosing a site for the Hera600 device.
Ÿ Ensure that all reasonable precautions are taken in the site choice
and installation of this product. Ensure that all warnings and
installation instructions have been read and understood. Eseye
Design are not liable for consequential loss or damage which arises
from installations where the instructions & warnings in this quick start
guide are not adhered to.
Warranty Information:
Ÿ Ensure there is a mains power outlet within 1 metre of the Hera600
installation. Do not modify the mains adapter.
Ÿ The Hera600 is primarily designed to be wall mounted. It is
recommended to install the Hera600 using the fixings supplied with
the product. Ensure all cables and antennas are securely located,
screwed or latched as appropriate to avoid intermittent connection
problems.
Ÿ Cellular signal strength, WiFi strength and signal interference from
other equipment should be considered in the location of the product,
in addition to visibility of the front & bottom panel indicators.
Ÿ Do not place the unit close to a heat source (such as other electrical
equipment) or in direct sunlight.
Ÿ Avoid locations exposed to heavy soiling due to exhaust from
machinery, liquid or airborne particles from industrial processes or
excessive dust.
Ÿ Do not insert or remove a SIM card when the product is powered. This
will cause problems with the functionality of the product. Always
power off before inserting or extracting a SIM card.
Ÿ The Hera600 should be located indoors in a stable a vibration free
environment between -20 to +55 degrees celsius, where relative
humidity is between 0 - 95% non condensing.
FCC ID: 2AASBH604V4 Contains FCC ID: N7NEM7455 IC: 11329A-H604V4 Contains IC: 2417C-EM7455 Model: H604V5