Product Overview

Spec Sheet #S00127
For Delivery by Fax Call 1-800-942-4636
Internet See MSDS section of
www.herchem.com
Mail Contact Hercules at address below or
any Hercules representative
®
ISO 9001: 2000 Certified
©2010 HCCI / KA / EW / 1010 / 2000
Hercules Chemical Company, Inc.
111 South Street, Passaic, NJ 07055-9100
Phone: [phone] • Fax: [phone]
e-mail: [e-mail]
www.herchem.com
APPROvAlS AND lISTINGS
Certified by NSF International to NSF/ANSI Standard 61 for
drinking water contact. Conforms to ASTM D-4236
SPECIFIC USES
ProPoxy 20 can be used to seal, mend, bond, and repair
almost anything in plumbing, heating, industrial, maintenance,
and home applications except areas of combustion and
exhaust where temperatures typically exceed 300° F.
Copper Poxy quickly repairs pipes, tanks and vessels made of
copper, brass, bronze and other non-ferrous metals.
Plastic Poxy can be used to seal, mend, bond and repair plas
-
tic plumbing, fixtures, appliances and automotive parts.
SPECIFIC APPlICATIONS*
Resistant to hydrocarbons, ketones, alcohols, esters,
halocarbons, aqueous salt solutions and dilute acids and bases.
NOT INTENDED FOR STRUCTURAL APPLICATIONS
WARNINGS OR CAUTIONS
• Read all cautions and directions carefully before using
product.
• KEEP OUT OF REACH OF CHILDREN.
• Not for use on polyethylene, polybutylene or polypropylene
parts such as gasoline tanks.
• Use caution when using on containers or piping carrying
hazardous or toxic substances.
• Contains Epoxy Resin and Tri(dimethylaminomethyl)phenol.
Exposure may cause allergic reactions.
• Harmful if swallowed. Get prompt medical attention if
ingested.
• Eye irritant. If eye contact occurs, rinse with tap water for at
least 15 minutes. If irritation persists, seek medical care.
• Skin irritant. Wash hands thoroughly with soap and water
after use. If skin irritation occurs, seek medical attention.
• Do not use for structural applications or on surfaces in
contact with food.
• Do not use in fish tanks. Even when cured, these products
may be fatal to fish.
DIRECTIONS FOR USE.
No waste. Cut or break off only amount needed for the job.
When mixed, Triple Play epoxy can be molded like putty to
desired shapes. For best results, surfaces should be cleaned
of grease and dirt. Smooth surfaces should be roughened by
ling or sanding prior to application. Thorough mixing of each
epoxy assures best product performance. Be sure product is
mixed until it is uniform in color - not streaky. Mixing in a cold
environment may be difcult; warm the product to room
temperature before mixing.
1) Remove protective end dots and cut or twist off a section of
the desired epoxy. 2) Roll and knead the epoxy in palms and
between ngers and hands. Fold over repeatedly and continue
rolling and kneading until streaks disappear and color is
uniform.
3) Apply at once to clean, dry surfaces. Force into
cracks or holes being repaired. For smooth appearance, hand
rub with water or damp cloth before material cures and
hardens. Remove any excess material before hardening
begins. The epoxy can be drilled, sawed, led, carved, sanded,
stained or painted. (When sanding cured any epoxy or
substrate, use protective eye wear and dust mask.) Full curing
will occur in 24 hours. To extend the life of Triple Play epoxy,
recover ends of stick with protective dots and store in original
package with cap tightly afxed. If protective dots are missing
or damaged, use aluminum foil or plastic kitchen wrap.
PHYSICAl PROPERTIES
MATERIAl SAFETY INFORMATION
FOR MORE INFORMATION ON THIS PRODUCT,
REQUEST MATERIAl SAFETY DATA SHEET (MSDS) #127,
ANSI MSDS #378
*For special applications which may not be covered on this or othe-
Hercules literature, please contact Hercules Technical Services
Department by phone [phone], or fax [phone], or
visit our technical database web-site at www.herchem.com.
propoxy TRIPLE PLAY
®
ProPoxy20 Copper Poxy Plastic Poxy
Density 15.8 Ib./gal. 15.8 lb/gal 13.4 lb /gal
Compression
Strength
18,000 psi 8,000 psi 8,000 psi
Hardness
(Shore D)
85 80 65
Maximum 300°F 250°F 250°F
Use continuous continuous
Temperature 300°F 300°F
intermittent intermittent
Appearance/ Black exterior Copper Blue exterior
color/odor and off-white exterior and and off-white
interior with off-white interior with
mercaptan interior with mercaptan
odor mercaptan odor odor
Electrical Properties:
Electrical 30,000 30,000 30,000
Resistivity megohms megohms megohms
Dielectric 300 volts/mil 300 volts/mil 300 volts/mi
Strength
Cure Times Work Life Functional Cure Full Cure
ProPoxy 20 5 – 8 Min 20 Min or less 24 Hrs
Copper Poxy 3 – 5 Min 20 Min or less 24 Hrs
Plastic Poxy 20 – 25 Min 40 Min or less 24 Hrs