Y Sayl® Disassembly for Recycling Table of Content 1. Work Chair Disassembly..................................................................................... 2 2. Side Chair Disassembly....................................................................................17 3. Work Stool Footring Disassembly.................................................................... 22 Z Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
Y Sayl® Disassembly for Recycling Work Chair Disassembly Tools Required: Flat Screw Driver Power driver T-40 Torx Driver Hammer Nose Plier Safety Glasses Rubber Mallet Materials Identification and Segregation: Where possible, plastic components are marked with ASTM recycling codes. Use these codes to identify material type for recycling. Non marked components should be treated as mixed plastic. Ferrous metals can be identified using a small magnet for recycling.
. Hold base legs firmly and strike the bottom of cylinder with a rubber mallet until base comes loose. 4. Disengage the base from cylinder. 5. Place one hand on can of cylinder and hit with hammer. 6. Remove cylinder. Z Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ® Y, Z, SAYL are among the registered trademarks of Herman Miller, Inc. TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
7. Pull arm to the highest position. 8. Using nose plier depress the retention clip. 9. Pull off the retention clip. 10. Depress the lock inward and pull the arm up to remove. Z Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ® Y, Z, SAYL are among the registered trademarks of Herman Miller, Inc. TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
11. Repeat 7 to 10 steps to remove other side arm. Note: If removing a no arm plug, depress the lock inward as in step 10 and remove arm plug. 12. Using T-20 torx driver remove arm pad screws (4 screws for adjustable pad, 1 screw for fixed pad. 13. Slide pad forward and off. Z Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ® Y, Z, SAYL are among the registered trademarks of Herman Miller, Inc.
14. Lay chair on back. Using flat head screw driver pry away (both sides until seat lock bar comes out). 15. Remove lock bar. 16. Release the seat lock move seat to the backward position. 17. Lift upward to remove. Z Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ® Y, Z, SAYL are among the registered trademarks of Herman Miller, Inc. TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
18. Remove all 4 T-20 torx screws. 19. Remove seat skirt. Seat skirt is also held on by 4 clips. Carefully pull the seat skirt loose from these clips. With screw driver pry out and remove any clips that remain lodged in the seat frame. 20. Slide latch to outside of seat frame until tabs are disengaged. 21. Unsnap the latch from seat frame and remove spring. Z Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
22. Remove the upholstery from seat. 23. Remove the seat foam from the seat bottom. 24. Using a power driver with T-40 torx remove top bolt. 25. Remove the bolt from tilt assembly. Z Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ® Y, Z, SAYL are among the registered trademarks of Herman Miller, Inc. TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
26. Remove the plate from the tilt assembly. 27. Using T-40 torx remove 2 screws from tilt assembly. 28. Remove bottom screw. 29. Slide off the back assembly. Z Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ® Y, Z, SAYL are among the registered trademarks of Herman Miller, Inc. TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
30. Remove top screws from each side using a T-25 torx from the frame. 31. Turn it over and remove back attachment screws using a T-20 torx. 32. Remove back attachment screws using a T-40 torx. 33. Remove pelvis. Z Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ® Y, Z, SAYL are among the registered trademarks of Herman Miller, Inc. TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
34. Using hand slightly pull back the spine from the back and remove the spine bracket plate from bottom of the back. 35. Insert a screw driver and rotate to expand the clip. 36. Pull spine off the back. 37. Use a T-20 torx wrench remove 1 screw from each pivot joint. Z Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ® Y, Z, SAYL are among the registered trademarks of Herman Miller, Inc. TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
38. Using T-25 torx remove 1 screw from each sleeve. 39. Pull sleeve off the back. 40. Slide out the plastic nut plate from slot towards bottom of the back. 41. Using thumb & fore finger squeeze handle snaps together. Z Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ® Y, Z, SAYL are among the registered trademarks of Herman Miller, Inc. TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
42. Remove lumbar handle. 43. Pull the upholstery from back. 44. Pull the foam and remove from back. 45. Remove scrim material from foam. Z Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ® Y, Z, SAYL are among the registered trademarks of Herman Miller, Inc. TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc. Illustrations and specifications are based on the latest product information available at the time of publication.
46. Using a nose plier remove hook on the bottom of the lumbar assembly. 47. After disassembling one side, pull the bow back so that it does not engage again. 48. Remove lumbar from back insert. 49. Remove suspension material. Z Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ® Y, Z, SAYL are among the registered trademarks of Herman Miller, Inc. TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
50. Pry the tab towards front of the tilt. 51. Pull out the handle assembly from tilt. 52. Slide off the lever form the assembly. 53. Pry the other side tab towards front of the tilt and pull out the lever. Z Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ® Y, Z, SAYL are among the registered trademarks of Herman Miller, Inc. TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
54. Slide off the other side lever from the assembly. Z 55. Pull off the tilt cover from tilt assembly. Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ® Y, Z, SAYL are among the registered trademarks of Herman Miller, Inc. TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc. Illustrations and specifications are based on the latest product information available at the time of publication.
Y Sayl® Disassembly for Recycling Side Chair Disassembly Side Chair Disassembly 1. Using philip head screw driver remove screw from front underside of seat pan. 2. Pull up on rear of cushion to disengage snap and slide seat cushion forward. 3. Using a power driver with a T-20 torx bit remove screws in seat pan. 4. Slide seat pan rearward until all tabs are disengaged. Z Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
5. Using a power driver with a T-15 torx bit remove arm screws from back side. 6. Using a rubber mallet tap on bottom of arm until arm comes out. 7. Pull off arms from both sides. 8. Pull or tap upward to remove back. Z Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ® Y, Z, SAYL are among the registered trademarks of Herman Miller, Inc. TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
9. Clamp on to a glide using a vice grip and tap vice grip using a rubber mallet until glide comes out. Repeat the step on other legs to remove the remaining 3 glides. 10. Place a rigid spacer between wheels on the body of caster and tap on it with a rubber mallet until caster wheel assembly comes off. Repeat the step on other legs to remove the remaining 3 casters. 11. Clamp on to a caster receptacle using a vice grip and tap vice grip using a rubber mallet until receptacle comes out. 12.
13. Remove the fabric from foam. 14. Remove fabric plastic back panel. 15. Pull the suspension material from back and remove. 16. Using a phillip head screw driver remove all screws from retainer. Z Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ® Y, Z, SAYL are among the registered trademarks of Herman Miller, Inc. TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
17. Remove the retainer from seat back. 18. Repeat step 16 to 17 remove rest of the pieces. Z Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ® Y, Z, SAYL are among the registered trademarks of Herman Miller, Inc. TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc. Illustrations and specifications are based on the latest product information available at the time of publication.
Y Sayl® Disassembly for Recycling Work Stool Footring Disassembly Work Stool Footring Disassembly 1. Place nylon cap over the end of cylinder and strike with hammer. 2. Disengage the base from cylinder. 3. Take out the footring from cylinder. Z Part no. 1b9rth rev B. © 2012 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ® Y, Z, SAYL are among the registered trademarks of Herman Miller, Inc. TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
