Quick Start Guide Please read the Quick Start Guide carefully before using the product and keep it. Related tools and documents of product, please download from www.herospeed.
1. WHAT’S IN THE BOX Battery Camera USB Cable Mount Bracket Adhesive Tape Screw Set User Guide 2. CAMERA DIAGRAM 1 2 3 1. LED Light 2. Microphone 3. 4MP Camera 4. LED Indicator 5. PIR Motion Sensor 6. Back Shell Open Button 7. Threaded Bracket Interface 8. Strong Magnetic Chuck 9. Speaker 10.
11 11. Reset hole 12. TF-card Slot 12 3. BATTERY CHARGING The batteries inside the Battery camera not fully charged in accordance with transportation safety regulations.
. DOWNLOAD THE APP Download and install the 'LongPlus' app from Google PlayTM or the App StoreTM. The App is also available by scanning the QR codes on the right, using your QR code scanner in your smart phone. NOTE: Google PlayTM is a trademark of Google Inc. App StoreTM is a service mark of Apple Inc. 5. WI-FI SET UP Before you start the Wi-Fi configuration, please note below: 1). The Battery camera works with 2.4 GHz Wi-Fi, but not with 5 GHz Wi-Fi. 2).
Launch the “LongPlus” APP and register an account with your mobile phone number of email ID. Start the Wi-Fi configuration, following the in-App instructions or refering to the following guiding steps. Guiding STEPS: 1.Tap ”+” to add device 1.Add device 7.Connecting 4.Select Wi-Fi 2.Turn on the camera 3.Voice prompt 8.Connection succeeds 9.Check signal strength -4- 10.Location name 5.Input password 11.Adding device complete 6.
. RUN A TEST After setup, tap on the live view window in the app for a test. Then take your Battery camera outside to the installation spot and run a test there. Make sure the installation spot is covered by strong 2.4 GHz Wi-Fi signal. If the battery camera doesn't work well outside, you may need to move the router closer to the installation spot or invest in a Wi-Fi extender. 7.
1 Screenshot 3 Speak 3 2 Video 4 Call 4 5 Quit Live View 2 5 NOTE: LIve viewing will not trigger device recording. 8. PLAYBACK If the Micro-SD card is properly installed, you can playback the video clips taken after motion detetion. A 7-days-rolling free cloud storage service is ready for your camera. You can also upgrade your cloud service pack in the settings. Tap to upgrade your cloud recording service pack and enable Smart Ai Motion Detetion area customization.
9. SHARE YOUR DEVICE Steps: Run LongPlus App >> Home >> Setting >> Share >> Camera sharing >> Let the administrator scan your QR Code. Setting 10. ALARM SETTING When a motion is detected by your camera, you will receive alarm notification from the App. You can also enable flashlight alarm and siren alarm to be triggered after motion events. The flashlight alarm and siren alarm can also be triggered manually in the camera settings.
11. INSTALLATION Adhesive Tape Nail the screw to the anchors, or directly to the wall until the bracket is fixed to the wall. You can also use the provided double-sided tape instead of screws to fix the wall mount on flat surface Attach the camera to the bracket and adjust the angle to cover the surveillance area. Do make sure the camera is within the Wi-Fi range. NOTE: LongPlus App will remind you to charge your camera when the battery is low.
Home Library User When you connect your camera through the LongPlus App, it will prompt you if the latest firmware is available. You can also manually check the firmware upgrade in the settings of the App. Please make sure your camera is fully charged or connected to a power source to upgrade the firmware. Do not cut off the power when upgrading the firmware. 12.TECHNICAL PARAMETERS Network Video & Audio 3 2.4 GHz ~ 2.4835 GHz 4 Ingenic T31ZX IEEE 802.
General FAQ Q1: How to invite family and friends to use my camera together? A1: Please refer to the guiding steps on page 7 of this user guide. Q2:Why doesn't the Wi-Fi name appear when I connect to Wi-Fi? A2: On Apple devices with iOS13 and above, you need to turn on the "location permission" for the app in the system settings and change it to "allow when using.
A3:The built-in infrared lamp beads make the camera only show some dim red lights when night vision is activated, but the image quality is still clear under no light environment. Q4:What are the requirements for Wi-Fi? A4:Please use a 2.4GHz wireless network. The device does not support the 5GHz wireless network. Meanwhile, please set the Wi-Fi authentication method to wpa2-psk or other lower level of security method. A password is required.
