Manual

ManualsBrandsHES ManualsAccessories for electricalHT1006

1006 Electric Strike Body

Trim Enhancer (with screws)

HT1006 Series Electric Strike

Installation Instructions

Product Components

Keeper Shims (2, with screws)

ASSA ABLOY, the global leader

in door opening solutions

FIVE YEAR LIMITED WARRANTY

For any questions regarding this information, call HES Customer Support at 1-800-626-7590

22630 N. 17th Ave. Phoenix, AZ 85027 www.hesinnovations.com

For UL Listed applications, the unit shall be connected to a UL Listed Class 2 power supply or a UL 294 Listed control unit.

ELECTRICAL RATINGS

Average Amp: 0.5 Seated

Average Amp: 0.04 Unseated

+12 to +24 (+/-10%) Volts DC

MINIMUM WIRE GAUGE Solenoid Voltage

REQUIREMENTS

24 VDC

200 feet or less

18 gauge

16 gauge

Keeper Latchbolt Monitor

18 gauge 18 gauge

16 gauge

14 gauge

12 VDC

200 - 300 feet

300 - 400 feet

Summary of content (11 pages)

PAGE 1
Installation Instructions HT1006 Series Electric Strike 1 Product Components 1 2 1006 Electric Strike Body Trim Enhancer (with screws) 3 4 Keeper Latchbolt Monitor Keeper Shims (2, with screws) 1 4 2 3 ELECTRICAL RATINGS +12 to +24 (+/-10%) Volts DC Average Amp: 0.5 Seated Average Amp: 0.
PAGE 2
Installation Instructions 2 Hi-O Overview ASSA ABLOY’s standard-based Hi-O system—Highly Intelligent Opening—connects electronic door components together over a CAN (Controller Area Network) data network, allowing them to communicate and monitor the health of the opening. Intelligence is built into each device instead of one centralized logic unit, creating a plug-and-play system.
PAGE 3
Installation Instructions 3 Prepare Strike Wiring The HT1006 series drawing below show the Hi-O application Voltage: 12-24VDC (11-28VDC range) operation Filtered and Regulated Power Supply Current: .5 Amp Seated .04 Amp Unseated A.
PAGE 4
Installation Instructions 4 Adjustment Instructions The default factory settings will be used in almost every application. They are:  Group 1  Terminator OFF NOTE: In some situations (such as mantraps) the default factory settings must be chaged. Refer to the Hi-O Systems Manual (A8002) for additional information. If so, follow the procedure below to change the DIP switch settings before installing strike IMPORTANT: Ensure that the serial number of the unit is retained.
PAGE 5
Installation Instructions Hi-O System Software Step 1: Install hardware according to installation instructions and the Hi-O System Manual. Step 3 Step 2: Download and install the latest release of Hi-O Step 3 Manager and Logger software, and DDF files according to the Hi-O System Manual. Step 3: Open Hi-O Manager and click the Next button to determine what devices are attached to the system. Step 4: Icons representing system appear in the left pane. Step 5: Click the Push Button icon.
PAGE 6
Installation Instructions 6 Hi-O Systems Settings Select the Properties tab.  Click the Push Button icon in the view pane.  Click the Advance Properties arrow to expand the menu.
PAGE 7
Installation Instructions 7 Hi-O System Settings De vic e Offlin e Be ha vio r Vo lt ag e Ou t of Ra ng e L imits J a m T ime rs Device Offline Behavior  No Change  Lock  Unlock Set Voltage Out of Range Limits Establishes Out of Range entries in Log.  Low Overflow Voltage in Volts  High Overflow Voltage in Volts 11 to 28 is the normal range. Set Jam Timers Set time to dictate when a jam message is sent when the strike is locked and keeper open.
PAGE 8
Installation Instructions 7 Hi-O System Settings De vic e Offlin e Be ha vio r Vo lt ag e Ou t of Ra ng e L imits J a m T ime rs Device Offline Behavior  No Change  Lock  Unlock Set Voltage Out of Range Limits Establishes Out of Range entries in Log.  Low Overflow Voltage in Volts  High Overflow Voltage in Volts 11 to 28 is the normal range. Set Jam Timers Set time to dictate when a jam message is sent when the strike is locked and keeper open.
PAGE 9
Cutout Templates 8 Inches [mm] HT1006 WITH CYLINDRICAL LOCKSETS HT1006 WITH MORTISE LOCKSETS Please note the horizontal centerline of the electric strike in relation to the centerline of the mortise lockset. CL Vertical Centerline Mortise Lockset Please note the horizontal centerline of the electric strike in relation to the centerline of the cylindrical lockset. Strike Prep CL Vertical Centerline Cylindrical Lock CL Strike 4" Strike Prep CL STRIKE [101.6] 3-1/2" 4-1/8" 4-7/8" 8" [88.
PAGE 10
Faceplate Options (4-7/8 x 1-1/4 SQUARE CORNER) 9 CL = center line of faceplate Inches [mm] (2nd line = center line of faceplate opening) Inches [mm] ND OPTION FACEPLATE 5/32” [3.97] N OPTION FACEPLATE 3-1/8” [79.37] 3-1/8” [79.37] 1-1/16” [26.72] 1-11/32” [34.11] 23/32” [18.22] Z OPTION FACEPLATE 5/16” [7.79] 1-15/32” [37.29] 1-25/64” [35.48] 1/8” [3.17] 2-7/8” [73.02] 1-9/64” [28.83] 7/8” [22.23] 23/32” [18.
PAGE 11
HT1006 ELECTRIC STRIKE INSTALLATION INSTRUCTIONS 3062006.003 rev A 2009 HES Inc.