Use and Care Manual

ManualsBrandsHessaire ManualsEvaporative Coolers1,100 CFM 3-Speed Portable Evaporative Cooler (Swamp Cooler) for 400 sq. ft.

Getting started

IInspection:

After unpacking your evaporative cooler, carefully inspect for any damage that may have

occurred during transit. Inspect for loose, missing or damaged.

CContents:

Evaporative Cooler

(1)

Hardware Bag (1)

Casters (4)

TTools / Materials

NNeeded:

Drill with #2

Phillip’s bit

Or Phillip’s head

screwdriver

UUse all precautions and

ddisconnect from power source

bbefore performing any

mmaintenance.

Operating Instructions

Evaporative cooling works on the principle of heat absorption by moisture evaporation.

Simply put, heat is removed from the air as water evaporates. You feel this principle in

action when you step out of a swimming pool or shower and feel cool as water evaporates

from the surface of your skin.

Your evaporative cooler works on the same principle. The fan pulls hot outside air through

the wet cooling pads, where the air is cooled by evaporation and then discharged from the

cooler.

Summary of content (9 pages)

PAGE 1
Use all precautions and disconnect from power source before performing any maintenance. Getting started Tools / Materials Needed: Contents: Evaporative Cooler (1) Drill with #2 Phillip’s bit Hardware Bag (1) Or Phillip’s head screwdriver Casters (4) Operating Instructions Evaporative cooling works on the principle of heat absorption by moisture evaporation. Simply put, heat is removed from the air as water evaporates.
PAGE 2
Hessaire Products Inc. Manufacturing Warranty EVAPORATIVE COOLER Each new cooler is warrantied to be free from defects in material or workmanship for one full year from the date of original purchase. If a component is found to be defective in this one year period, it will be repaired or replaced with a new or refurbished product at the option of the factory. Should a warranty issue arise, please contact the dealer from whom the fan was purchased.
PAGE 3
Section 3 Getting started Key Operational Points: 1. Your cooler must be positioned in front of an open window or door if it is to operate effectively. 2. Always ensure that there is another open window or door through which the air can exhaust from the room. 3. Ensure the filter is kept clean throughout the summer season. 4. At the end of each day run your cooler on FAN ONLY for 30 minutes to dry out the filter. 5. Prior to putting your cooler away for winter, always: a. Drain the tank and wipe out clean.
PAGE 4
Safety Rules 1. Read and follow all instructions, cautions, and warnings. Failure to do so could result in personal injury, death or property damage. 2. Unit must be in the OFF position and UNPLUGGED from power receptacle before performing any maintenance. 3. Make sure the electrical power source conforms to the requirement of the evaporative cooler(s) as well as local codes. 4. To reduce the risk of fire or electrical shock, do not expose electrical connections to water. 5.
PAGE 5
Section 4A Cooler Set Up and Operation Hessaire Coolers are pre-assembled and ready to operate. Simply remove the packaging and then carefully remove the unit from the box. Install Casters. Lock the 2 locking wheels before filling and turning on fan to keep the cooler from moving from the air velocity. NOTICE: the Xel50 Media pad will have a slight odor when it is new. This is normal. It will dissipate after a period of time depending on the use time.
PAGE 6
Section 4B Connecting to a power supply. Plug the Hessaire cooler into any 115 volt power supply. It is permissible to use extension cords when needed. It is not recommended to use a GFCI circuit usually found in garage or patio areas. These outlets/circuits are sensitive and may trip inadvertently to the cooler in normal operation. Should that be the only power supply please be aware of this and if the GFCI trips simply reset it.
PAGE 7
Section 5 Cooler Maintenance WARNING: (DO NOT remove back panel with cooler running) For best operation and long useful life the following maintenance and cleaning procedures should be followed. Cleaning Cooler and Pads At regular intervals your Hessaire Mobile cooler should be shut down and disconnected from power supply. The water tank should be drained of dirty water and sprayed out with fresh water and refilled.
PAGE 8
Removal and Replacement of Xel50 Cooling Media. The cooling pads are made from a special resin impregnated craft paper specially designed for evaporative cooling. They will last many years if maintained properly and water quality is maintained. It is not necessary to remove the pads to clean them. Inspect the pads for deposits of calcium on the air entering side. If the flute cells are clogged or the pad is very heavy it may be time to change the media.
PAGE 9
high or too low) or remove and replace a float that has failed to shut of water supply. Note: Be sure that the PSI of the supply water is within the 50 PSI spec. before determining the float has failed. 1. 2. 3. 4. 5. The float valve can be purchased where you purchased your cooler. Remove any hose adapters attached to the float valve nipple. Remove the rear panel assembly as instructed in Section 5. Remove the float valve retaining nut and rubber washer. Remove float valve from cabinet.